[MIPS] Alchemy: move UART platform code to its proper place

[linux-2.6-omap-h63xx.git] / drivers / serial / Kconfig

diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 6a44fb1dc167c0c74a39ac161f287e68c64e212f..34b809e3b59651dd17ec404ebd3bc9a1be0a421a 100644 (file)
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -262,12 +262,12 @@ config SERIAL_8250_ACORN
          cards.  If unsure, say N.
 
 config SERIAL_8250_AU1X00
-       bool "AU1X00 serial port support"
+       bool "Au1x00 serial port support"
        depends on SERIAL_8250 != n && SOC_AU1X00
        help
-         If you have an Au1x00 board and want to use the serial port, say Y
-         to this option.  The driver can handle 1 or 2 serial ports.
-         If unsure, say N.
+         If you have an Au1x00 SOC based board and want to use the serial port,
+         say Y to this option. The driver can handle up to 4 serial ports,
+         depending on the SOC. If unsure, say N.
 
 config SERIAL_8250_RM9K
        bool "Support for MIPS RM9xxx integrated serial port"
@@ -380,6 +380,21 @@ config SERIAL_ATMEL_CONSOLE
          console is the device which receives all kernel messages and
          warnings and which allows logins in single user mode).
 
+config SERIAL_ATMEL_PDC
+       bool "Support DMA transfers on AT91 / AT32 serial port"
+       depends on SERIAL_ATMEL
+       default y
+       help
+         Say Y here if you wish to use the PDC to do DMA transfers to
+         and from the Atmel AT91 / AT32 serial port. In order to
+         actually use DMA transfers, make sure that the use_dma_tx
+         and use_dma_rx members in the atmel_uart_data struct is set
+         appropriately for each port.
+
+         Note that break and error handling currently doesn't work
+         properly when DMA is enabled. Make sure that ports where
+         this matters don't use DMA.
+
 config SERIAL_ATMEL_TTYAT
        bool "Install as device ttyATn instead of ttySn"
        depends on SERIAL_ATMEL=y
@@ -465,20 +480,24 @@ config SERIAL_DZ
        bool "DECstation DZ serial driver"
        depends on MACH_DECSTATION && 32BIT
        select SERIAL_CORE
-       help
-         DZ11-family serial controllers for VAXstations, including the
-         DC7085, M7814, and M7819.
+       default y
+       ---help---
+         DZ11-family serial controllers for DECstations and VAXstations,
+         including the DC7085, M7814, and M7819.
 
 config SERIAL_DZ_CONSOLE
        bool "Support console on DECstation DZ serial driver"
        depends on SERIAL_DZ=y
        select SERIAL_CORE_CONSOLE
-       help
+       default y
+       ---help---
          If you say Y here, it will be possible to use a serial port as the
          system console (the system console is the device which receives all
          kernel messages and warnings and which allows logins in single user
-         mode).  Note that the firmware uses ttyS0 as the serial console on
-         the Maxine and ttyS2 on the others.
+         mode).
+
+         Note that the firmware uses ttyS3 as the serial console on
+         DECstations that use this driver.
 
          If unsure, say Y.
 
@@ -667,7 +686,7 @@ config UART0_RTS_PIN
 
 config SERIAL_BFIN_UART1
        bool "Enable UART1"
-       depends on SERIAL_BFIN && (BF534 || BF536 || BF537 || BF54x)
+       depends on SERIAL_BFIN && (!BF531 && !BF532 && !BF533 && !BF561)
        help
          Enable UART1
 
@@ -680,14 +699,14 @@ config BFIN_UART1_CTSRTS
 
 config UART1_CTS_PIN
        int "UART1 CTS pin"
-       depends on BFIN_UART1_CTSRTS && (BF53x || BF561)
+       depends on BFIN_UART1_CTSRTS && !BF54x
        default -1
        help
          Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
 
 config UART1_RTS_PIN
        int "UART1 RTS pin"
-       depends on BFIN_UART1_CTSRTS && (BF53x || BF561)
+       depends on BFIN_UART1_CTSRTS && !BF54x
        default -1
        help
          Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
@@ -942,6 +961,9 @@ config SERIAL_CORE
 config SERIAL_CORE_CONSOLE
        bool
 
+config CONSOLE_POLL
+       bool
+
 config SERIAL_68328
        bool "68328 serial support"
        depends on M68328 || M68EZ328 || M68VZ328
@@ -1138,17 +1160,17 @@ config SERIAL_SGI_L1_CONSOLE
                say Y.  Otherwise, say N.
 
 config SERIAL_MPC52xx
-       tristate "Freescale MPC52xx family PSC serial support"
-       depends on PPC_MPC52xx
+       tristate "Freescale MPC52xx/MPC512x family PSC serial support"
+       depends on PPC_MPC52xx || PPC_MPC512x
        select SERIAL_CORE
        help
-         This drivers support the MPC52xx PSC serial ports. If you would
-         like to use them, you must answer Y or M to this option. Not that
+         This driver supports MPC52xx and MPC512x PSC serial ports. If you would
+         like to use them, you must answer Y or M to this option. Note that
          for use as console, it must be included in kernel and not as a
          module.
 
 config SERIAL_MPC52xx_CONSOLE
-       bool "Console on a Freescale MPC52xx family PSC serial port"
+       bool "Console on a Freescale MPC52xx/MPC512x family PSC serial port"
        depends on SERIAL_MPC52xx=y
        select SERIAL_CORE_CONSOLE
        help
@@ -1156,7 +1178,7 @@ config SERIAL_MPC52xx_CONSOLE
          of the Freescale MPC52xx family as a console.
 
 config SERIAL_MPC52xx_CONSOLE_BAUD
-       int "Freescale MPC52xx family PSC serial port baud"
+       int "Freescale MPC52xx/MPC512x family PSC serial port baud"
        depends on SERIAL_MPC52xx_CONSOLE=y
        default "9600"
        help