* mapbase is the physical address of the IO port.
* membase is an 'ioremapped' cookie.
*/
-#include <linux/config.h>
#if defined(CONFIG_SERIAL_8250_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
/*
* Configuration:
- * share_irqs - whether we pass SA_SHIRQ to request_irq(). This option
+ * share_irqs - whether we pass IRQF_SHARED to request_irq(). This option
* is unsafe when used on edge-triggered interrupts.
*/
static unsigned int share_irqs = SERIAL8250_SHARE_IRQS;
static unsigned int serial_in(struct uart_8250_port *up, int offset)
{
+ unsigned int tmp;
offset = map_8250_in_reg(up, offset) << up->port.regshift;
switch (up->port.iotype) {
return __raw_readl(up->port.membase + offset);
#endif
+ case UPIO_TSI:
+ if (offset == UART_IIR) {
+ tmp = readl((u32 *)(up->port.membase + UART_RX));
+ return (cpu_to_le32(tmp) >> 8) & 0xff;
+ } else
+ return readb(up->port.membase + offset);
+
default:
return inb(up->port.iobase + offset);
}
__raw_writel(value, up->port.membase + offset);
break;
#endif
+ case UPIO_TSI:
+ if (!((offset == UART_IER) && (value & UART_IER_UUE)))
+ writeb(value, up->port.membase + offset);
+ break;
default:
outb(value, up->port.iobase + offset);
static int serial_link_irq_chain(struct uart_8250_port *up)
{
struct irq_info *i = irq_lists + up->port.irq;
- int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? SA_SHIRQ : 0;
+ int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? IRQF_SHARED : 0;
spin_lock_irq(&i->lock);
serial_outp(up, UART_EFR, efr);
}
+#ifdef CONFIG_ARCH_OMAP15XX
+ /* Workaround to enable 115200 baud on OMAP1510 internal ports */
+ if (cpu_is_omap1510() && is_omap_port((unsigned int)up->port.membase)) {
+ if (baud == 115200) {
+ quot = 1;
+ serial_out(up, UART_OMAP_OSC_12M_SEL, 1);
+ } else
+ serial_out(up, UART_OMAP_OSC_12M_SEL, 0);
+ }
+#endif
+
if (up->capabilities & UART_NATSEMI) {
/* Switch to bank 2 not bank 1, to avoid resetting EXCR2 */
serial_outp(up, UART_LCR, 0xe0);
case UPIO_AU:
size = 0x100000;
/* fall thru */
+ case UPIO_TSI:
+ case UPIO_MEM32:
case UPIO_MEM:
if (!up->port.mapbase)
break;
case UPIO_AU:
size = 0x100000;
/* fall thru */
+ case UPIO_TSI:
+ case UPIO_MEM32:
case UPIO_MEM:
if (!up->port.mapbase)
break;
{
unsigned long start = UART_RSA_BASE << up->port.regshift;
unsigned int size = 8 << up->port.regshift;
- int ret = 0;
+ int ret = -EINVAL;
switch (up->port.iotype) {
- case UPIO_MEM:
- ret = -EINVAL;
- break;
-
case UPIO_HUB6:
case UPIO_PORT:
start += up->port.iobase;
- if (!request_region(start, size, "serial-rsa"))
+ if (request_region(start, size, "serial-rsa"))
+ ret = 0;
+ else
ret = -EBUSY;
break;
}
unsigned int size = 8 << up->port.regshift;
switch (up->port.iotype) {
- case UPIO_MEM:
- break;
-
case UPIO_HUB6:
case UPIO_PORT:
release_region(up->port.iobase + offset, size);
touch_nmi_watchdog();
- if (oops_in_progress) {
- locked = spin_trylock_irqsave(&up->port.lock, flags);
+ local_irq_save(flags);
+ if (up->port.sysrq) {
+ /* serial8250_handle_port() already took the lock */
+ locked = 0;
+ } else if (oops_in_progress) {
+ locked = spin_trylock(&up->port.lock);
} else
- spin_lock_irqsave(&up->port.lock, flags);
+ spin_lock(&up->port.lock);
/*
* First save the IER then disable the interrupts
serial_out(up, UART_IER, ier);
if (locked)
- spin_unlock_irqrestore(&up->port.lock, flags);
+ spin_unlock(&up->port.lock);
+ local_irq_restore(flags);
}
static int serial8250_console_setup(struct console *co, char *options)
/**
* serial8250_suspend_port - suspend one serial port
* @line: serial line number
- * @level: the level of port suspension, as per uart_suspend_port
*
* Suspend one serial port.
*/
/**
* serial8250_resume_port - resume one serial port
* @line: serial line number
- * @level: the level of port resumption, as per uart_resume_port
*
* Resume one serial port.
*/