Merge with /home/tmlind/src/kernel/linux-2.6

[linux-2.6-omap-h63xx.git] / drivers / serial / 8250.c

diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 7aca22c9976d0f37a9d8f3e0b0cf6a41d6a3d787..8b1fc5aa3032862abc875df00554db3c9d45634d 100644 (file)
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -1342,7 +1342,8 @@ static irqreturn_t serial8250_interrupt(int irq, void *dev_id, struct pt_regs *r
 
        DEBUG_INTR("end.\n");
 
-       return IRQ_RETVAL(handled);
+       //return IRQ_RETVAL(handled);
+       return IRQ_HANDLED;     /* FIXME: iir status not ready on 1510 */
 }
 
 /*
@@ -1855,6 +1856,17 @@ serial8250_set_termios(struct uart_port *port, struct termios *termios,
                serial_outp(up, UART_EFR, efr);
        }
 
+#ifdef CONFIG_ARCH_OMAP15XX
+       /* Workaround to enable 115200 baud on OMAP1510 internal ports */
+       if (cpu_is_omap1510() && is_omap_port((unsigned int)up->port.membase)) {
+               if (baud == 115200) {
+                       quot = 1;
+                       serial_out(up, UART_OMAP_OSC_12M_SEL, 1);
+               } else
+                       serial_out(up, UART_OMAP_OSC_12M_SEL, 0);
+        }
+#endif
+
        if (up->capabilities & UART_NATSEMI) {
                /* Switch to bank 2 not bank 1, to avoid resetting EXCR2 */
                serial_outp(up, UART_LCR, 0xe0);
@@ -1879,6 +1891,19 @@ serial8250_set_termios(struct uart_port *port, struct termios *termios,
                        /* emulated UARTs (Lucent Venus 167x) need two steps */
                        serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
                }
+
+               /* Note that we need to set ECB to access write water mark
+                * bits. First allow FCR tx fifo write, then set fcr with
+                * possible TX fifo settings. */
+               if (uart_config[up->port.type].flags & UART_CAP_EFR) {
+                       serial_outp(up, UART_LCR, 0xbf);        /* Access EFR */
+                       serial_outp(up, UART_EFR, UART_EFR_ECB);
+                       serial_outp(up, UART_LCR, 0x0);         /* Access FCR */
+                       serial_outp(up, UART_FCR, fcr);
+                       serial_outp(up, UART_LCR, 0xbf);        /* Access EFR */
+                       serial_outp(up, UART_EFR, 0);
+                       serial_outp(up, UART_LCR, cval);        /* Access FCR */
+        } else
                serial_outp(up, UART_FCR, fcr);         /* set fcr */
        }
        serial8250_set_mctrl(&up->port, up->port.mctrl);
@@ -1905,6 +1930,11 @@ static int serial8250_request_std_resource(struct uart_8250_port *up)
        unsigned int size = 8 << up->port.regshift;
        int ret = 0;
 
+#ifdef CONFIG_ARCH_OMAP
+       if (is_omap_port((unsigned int)up->port.membase))
+               size = 0x16 << up->port.regshift;
+#endif
+
        switch (up->port.iotype) {
        case UPIO_MEM:
                if (!up->port.mapbase)