Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4

[linux-2.6-omap-h63xx.git] / drivers / net / bnx2x_init.h

diff --git a/drivers/net/bnx2x_init.h b/drivers/net/bnx2x_init.h
index 4c7750789b62309ca7d410c51122dbafa395d394..a6c0b3abba290a9cd75c7b7c4a764874c4e55801 100644 (file)
--- a/drivers/net/bnx2x_init.h
+++ b/drivers/net/bnx2x_init.h
@@ -72,26 +72,26 @@
 
 
 struct raw_op {
-       u32 op          :8;
-       u32 offset      :24;
+       u32 op:8;
+       u32 offset:24;
        u32 raw_data;
 };
 
 struct op_read {
-       u32 op          :8;
-       u32 offset      :24;
+       u32 op:8;
+       u32 offset:24;
        u32 pad;
 };
 
 struct op_write {
-       u32 op          :8;
-       u32 offset      :24;
+       u32 op:8;
+       u32 offset:24;
        u32 val;
 };
 
 struct op_string_write {
-       u32 op          :8;
-       u32 offset      :24;
+       u32 op:8;
+       u32 offset:24;
 #ifdef __LITTLE_ENDIAN
        u16 data_off;
        u16 data_len;
@@ -102,8 +102,8 @@ struct op_string_write {
 };
 
 struct op_zero {
-       u32 op          :8;
-       u32 offset      :24;
+       u32 op:8;
+       u32 offset:24;
        u32 len;
 };
 
@@ -208,7 +208,7 @@ static void bnx2x_init_wr_64(struct bnx2x *bp, u32 addr, const u32 *data,
 /*********************************************************
    There are different blobs for each PRAM section.
    In addition, each blob write operation is divided into a few operations
-   in order to decrease the amount of phys. contigious buffer needed.
+   in order to decrease the amount of phys. contiguous buffer needed.
    Thus, when we select a blob the address may be with some offset
    from the beginning of PRAM section.
    The same holds for the INT_TABLE sections.
@@ -336,7 +336,7 @@ static void bnx2x_init_block(struct bnx2x *bp, u32 op_start, u32 op_end)
                len = op->str_wr.data_len;
                data = data_base + op->str_wr.data_off;
 
-               /* carefull! it must be in order */
+               /* careful! it must be in order */
                if (unlikely(op_type > OP_WB)) {
 
                        /* If E1 only */
@@ -564,14 +564,15 @@ static const struct arb_line write_arb_addr[NUM_WR_Q-1] = {
 
 static void bnx2x_init_pxp(struct bnx2x *bp)
 {
+       u16 devctl;
        int r_order, w_order;
        u32 val, i;
 
        pci_read_config_word(bp->pdev,
-                            bp->pcie_cap + PCI_EXP_DEVCTL, (u16 *)&val);
-       DP(NETIF_MSG_HW, "read 0x%x from devctl\n", (u16)val);
-       w_order = ((val & PCI_EXP_DEVCTL_PAYLOAD) >> 5);
-       r_order = ((val & PCI_EXP_DEVCTL_READRQ) >> 12);
+                            bp->pcie_cap + PCI_EXP_DEVCTL, &devctl);
+       DP(NETIF_MSG_HW, "read 0x%x from devctl\n", devctl);
+       w_order = ((devctl & PCI_EXP_DEVCTL_PAYLOAD) >> 5);
+       r_order = ((devctl & PCI_EXP_DEVCTL_READRQ) >> 12);
 
        if (r_order > MAX_RD_ORD) {
                DP(NETIF_MSG_HW, "read order of %d  order adjusted to %d\n",
@@ -740,7 +741,7 @@ static u8 calc_crc8(u32 data, u8 crc)
        return crc_res;
 }
 
-/* regiesers addresses are not in order
+/* registers addresses are not in order
    so these arrays help simplify the code */
 static const int cm_start[E1H_FUNC_MAX][9] = {
        {MISC_FUNC0_START, TCM_FUNC0_START, UCM_FUNC0_START, CCM_FUNC0_START,