config MACB
tristate "Atmel MACB support"
- depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91CAP9
+ depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
select PHYLIB
help
The Atmel MACB ethernet interface is found on many AT32 and AT91
To compile this driver as a module, choose M here: the module
will be called apne.
-config APOLLO_ELPLUS
- tristate "Apollo 3c505 support"
- depends on APOLLO
- help
- Say Y or M here if your Apollo has a 3Com 3c505 ISA Ethernet card.
- If you don't have one made for Apollos, you can use one from a PC,
- except that your Apollo won't be able to boot from it (because the
- code in the ROM will be for a PC).
-
config MAC8390
bool "Macintosh NS 8390 based ethernet cards"
depends on MAC
If unsure, say Y.
-config LAN_SAA9730
- bool "Philips SAA9730 Ethernet support"
- depends on NET_PCI && PCI && MIPS_ATLAS
- help
- The SAA9730 is a combined multimedia and peripheral controller used
- in thin clients, Internet access terminals, and diskless
- workstations.
- See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>.
-
config SC92031
tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
depends on NET_PCI && PCI && EXPERIMENTAL
Say Y here if you want to use the NE2000 compatible
controller on the Renesas H8/300 processor.
-source "drivers/net/fec_8xx/Kconfig"
source "drivers/net/fs_enet/Kconfig"
endif # NET_ETHERNET
To compile this driver as a module, choose M here. The module
will be called e1000.
-config E1000_NAPI
- bool "Use Rx Polling (NAPI)"
- depends on E1000
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config E1000_DISABLE_PACKET_SPLIT
bool "Disable Packet Split for PCI express adapters"
depends on E1000
To compile this driver as a module, choose M here. The module
will be called igb.
+config IGB_LRO
+ bool "Use software LRO"
+ depends on IGB && INET
+ select INET_LRO
+ ---help---
+ Say Y here if you want to use large receive offload.
+
+ If in doubt, say N.
+
source "drivers/net/ixp2000/Kconfig"
config MYRI_SBUS
To compile this driver as a module, choose M here. The module
will be called atl1.
+config ATL1E
+ tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ select MII
+ help
+ This driver supports the Atheros L1E gigabit ethernet adapter.
+
+ To compile this driver as a module, choose M here. The module
+ will be called atl1e.
+
endif # NETDEV_1000
#
To compile this driver as a module, choose M here. The module
will be called ixgb.
-config IXGB_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on IXGB && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config S2IO
tristate "S2IO 10Gbe XFrame NIC"
depends on PCI