starfire: delete non NAPI code from the driver.

[linux-2.6-omap-h63xx.git] / drivers / net / Kconfig

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 287d0873c60d1201d6aa1ada48298369e5e46a02..9f7442fba47dd1f89fb6b1ab2270f0cacfb341a2 100644 (file)
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -938,6 +938,23 @@ config DM9000
          To compile this driver as a module, choose M here.  The module
          will be called dm9000.
 
+config DM9000_DEBUGLEVEL
+       int "DM9000 maximum debug level"
+       depends on DM9000
+       default 4
+       help
+         The maximum level of debugging code compiled into the DM9000
+         driver.
+
+config DM9000_FORCE_SIMPLE_PHY_POLL
+       bool "Force simple NSR based PHY polling"
+       depends on DM9000
+       ---help---
+         This configuration forces the DM9000 to use the NSR's LinkStatus
+         bit to determine if the link is up or down instead of the more
+         costly MII PHY reads. Note, this will not work if the chip is
+         operating with an external PHY.
+
 config ENC28J60
        tristate "ENC28J60 support"
        depends on EXPERIMENTAL && SPI && NET_ETHERNET
@@ -955,14 +972,6 @@ config ENC28J60_WRITEVERIFY
          Enable the verify after the buffer write useful for debugging purpose.
          If unsure, say N.
 
-config DM9000_DEBUGLEVEL
-       int "DM9000 maximum debug level"
-       depends on DM9000
-       default 4
-       help
-         The maximum level of debugging code compiled into the DM9000
-         driver.
-
 config SMC911X
        tristate "SMSC LAN911[5678] support"
        select CRC32
@@ -1325,20 +1334,6 @@ config ADAPTEC_STARFIRE
          To compile this driver as a module, choose M here: the module
          will be called starfire.  This is recommended.
 
-config ADAPTEC_STARFIRE_NAPI
-       bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
-       depends on ADAPTEC_STARFIRE && EXPERIMENTAL
-       help
-         NAPI is a new driver API designed to reduce CPU and interrupt load
-         when the driver is receiving lots of packets from the card. It is
-         still somewhat experimental and thus not yet enabled by default.
-
-         If your estimated Rx load is 10kpps or more, or if the card will be
-         deployed on potentially unfriendly networks (e.g. in a firewall),
-         then say Y here.
-
-         If in doubt, say N.
-
 config AC3200
        tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
        depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL
@@ -2025,9 +2020,6 @@ config E1000E
          To compile this driver as a module, choose M here. The module
          will be called e1000e.
 
-config E1000E_ENABLED
-       def_bool E1000E != n
-
 config IP1000
        tristate "IP1000 Gigabit Ethernet support"
        depends on PCI && EXPERIMENTAL
@@ -2116,27 +2108,13 @@ config R8169
          To compile this driver as a module, choose M here: the module
          will be called r8169.  This is recommended.
 
-config R8169_NAPI
-       bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
-       depends on R8169 && EXPERIMENTAL
-       help
-         NAPI is a new driver API designed to reduce CPU and interrupt load
-         when the driver is receiving lots of packets from the card. It is
-         still somewhat experimental and thus not yet enabled by default.
-
-         If your estimated Rx load is 10kpps or more, or if the card will be
-         deployed on potentially unfriendly networks (e.g. in a firewall),
-         then say Y here.
-
-         If in doubt, say N.
-
 config R8169_VLAN
        bool "VLAN support"
        depends on R8169 && VLAN_8021Q
        ---help---
          Say Y here for the r8169 driver to support the functions required
          by the kernel 802.1Q code.
-         
+
          If in doubt, say Y.
 
 config SB1250_MAC
@@ -2462,7 +2440,8 @@ config EHEA
 
 config IXGBE
        tristate "Intel(R) 10GbE PCI Express adapters support"
-       depends on PCI
+       depends on PCI && INET
+       select INET_LRO
        ---help---
          This driver supports Intel(R) 10GbE PCI Express family of
          adapters.  For more information on how to identify your adapter, go
@@ -2522,20 +2501,6 @@ config S2IO
          More specific information on configuring the driver is in 
          <file:Documentation/networking/s2io.txt>.
 
-config S2IO_NAPI
-       bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
-       depends on S2IO && EXPERIMENTAL
-       help
-         NAPI is a new driver API designed to reduce CPU and interrupt load
-         when the driver is receiving lots of packets from the card. It is
-         still somewhat experimental and thus not yet enabled by default.
-
-         If your estimated Rx load is 10kpps or more, or if the card will be
-         deployed on potentially unfriendly networks (e.g. in a firewall),
-         then say Y here.
-
-         If in doubt, say N.
-
 config MYRI10GE
        tristate "Myricom Myri-10G Ethernet support"
        depends on PCI && INET