If you don't have this card, of course say N.
+config IP1000
+ tristate "IP1000 Gigabit Ethernet support"
+ depends on PCI && EXPERIMENTAL
+ select MII
+ ---help---
+ This driver supports IP1000 gigabit Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called ipg. This is recommended.
+
source "drivers/net/arcnet/Kconfig"
source "drivers/net/phy/Kconfig"
AX88796 driver, using platform bus to provide
chip detection and resources
+config AX88796_93CX6
+ bool "ASIX AX88796 external 93CX6 eeprom support"
+ depends on AX88796
+ select EEPROM_93CX6
+ help
+ Select this if your platform comes with an external 93CX6 eeprom.
+
config MACE
tristate "MACE (Power Mac ethernet) support"
depends on PPC_PMAC && PPC32
If you have an Alchemy Semi AU1X00 based system
say Y. Otherwise, say N.
-config NET_SB1250_MAC
- tristate "SB1250 Ethernet support"
- depends on SIBYTE_SB1xxx_SOC
-
config SGI_IOC3_ETH
bool "SGI IOC3 Ethernet"
depends on PCI && SGI_IP27
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
-config SGI_IOC3_ETH_HW_RX_CSUM
- bool "Receive hardware checksums"
- depends on SGI_IOC3_ETH && INET
- default y
- help
- The SGI IOC3 network adapter supports TCP and UDP checksums in
- hardware to offload processing of these checksums from the CPU. At
- the moment only acceleration of IPv4 is supported. This option
- enables offloading for checksums on receive. If unsure, say Y.
-
-config SGI_IOC3_ETH_HW_TX_CSUM
- bool "Transmit hardware checksums"
- depends on SGI_IOC3_ETH && INET
- default y
- help
- The SGI IOC3 network adapter supports TCP and UDP checksums in
- hardware to offload processing of these checksums from the CPU. At
- the moment only acceleration of IPv4 is supported. This option
- enables offloading for checksums on transmit. If unsure, say Y.
-
config MIPS_SIM_NET
tristate "MIPS simulator Network device"
depends on MIPS_SIM
tristate "Blackfin 536/537 on-chip mac support"
depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
select CRC32
+ select MII
+ select PHYLIB
select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
help
This is the driver for blackfin on-chip mac device. Say Y if you want it
depends on BFIN_MAC && BF537
default y
help
- To get maximum network performace, you should use L1 memory as rx/tx buffers.
+ To get maximum network performance, you should use L1 memory as rx/tx buffers.
Say N here if you want to reserve L1 memory for other uses.
config BFIN_TX_DESC_NUM
tristate "SMSC LAN911[5678] support"
select CRC32
select MII
- depends on ARCH_PXA
+ depends on ARCH_PXA || SUPERH
help
This is a driver for SMSC's LAN911x series of Ethernet chipsets
including the new LAN9115, LAN9116, LAN9117, and LAN9118.
<file:Documentation/networking/net-modules.txt>. The module will
be called ibmveth.
-config IBM_EMAC
- tristate "PowerPC 4xx on-chip Ethernet support"
- depends on 4xx && !PPC_MERGE
- help
- This driver supports the PowerPC 4xx EMAC family of on-chip
- Ethernet controllers.
-
-config IBM_EMAC_RXB
- int "Number of receive buffers"
- depends on IBM_EMAC
- default "128"
-
-config IBM_EMAC_TXB
- int "Number of transmit buffers"
- depends on IBM_EMAC
- default "64"
-
-config IBM_EMAC_POLL_WEIGHT
- int "MAL NAPI polling weight"
- depends on IBM_EMAC
- default "32"
-
-config IBM_EMAC_RX_COPY_THRESHOLD
- int "RX skb copy threshold (bytes)"
- depends on IBM_EMAC
- default "256"
-
-config IBM_EMAC_RX_SKB_HEADROOM
- int "Additional RX skb headroom (bytes)"
- depends on IBM_EMAC
- default "0"
- help
- Additional receive skb headroom. Note, that driver
- will always reserve at least 2 bytes to make IP header
- aligned, so usually there is no need to add any additional
- headroom.
-
- If unsure, set to 0.
-
-config IBM_EMAC_PHY_RX_CLK_FIX
- bool "PHY Rx clock workaround"
- depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
- help
- Enable this if EMAC attached to a PHY which doesn't generate
- RX clock if there is no link, if this is the case, you will
- see "TX disable timeout" or "RX disable timeout" in the system
- log.
-
- If unsure, say N.
-
-config IBM_EMAC_DEBUG
- bool "Debugging"
- depends on IBM_EMAC
- default n
-
-config IBM_EMAC_ZMII
- bool
- depends on IBM_EMAC && (NP405H || NP405L || 44x)
- default y
-
-config IBM_EMAC_RGMII
- bool
- depends on IBM_EMAC && 440GX
- default y
-
-config IBM_EMAC_TAH
- bool
- depends on IBM_EMAC && 440GX
- default y
+source "drivers/net/ibm_emac/Kconfig"
+source "drivers/net/ibm_newemac/Kconfig"
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config AMD8111_ETH
will be called amd8111e.
config AMD8111E_NAPI
- bool "Enable NAPI support"
+ bool "Use RX polling (NAPI)"
depends on AMD8111_ETH
help
NAPI is a new driver API designed to reduce CPU and interrupt load
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config ADAPTEC_STARFIRE
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config AC3200
called apricot.
config B44
- tristate "Broadcom 4400 ethernet support"
- depends on NET_PCI && PCI
+ tristate "Broadcom 440x/47xx ethernet support"
+ depends on SSB_POSSIBLE
+ select SSB
select MII
help
- If you have a network (Ethernet) controller of this type, say Y and
- read the Ethernet-HOWTO, available from
+ If you have a network (Ethernet) controller of this type, say Y
+ or M and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here and read
<file:Documentation/networking/net-modules.txt>. The module will be
called b44.
+# Auto-select SSB PCI-HOST support, if possible
+config B44_PCI_AUTOSELECT
+ bool
+ depends on B44 && SSB_PCIHOST_POSSIBLE
+ select SSB_PCIHOST
+ default y
+
+# Auto-select SSB PCICORE driver, if possible
+config B44_PCICORE_AUTOSELECT
+ bool
+ depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE
+ select SSB_DRIVER_PCICORE
+ default y
+
+config B44_PCI
+ bool
+ depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT
+ default y
+
config FORCEDETH
tristate "nForce Ethernet support"
depends on NET_PCI && PCI
called forcedeth.
config FORCEDETH_NAPI
- bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
+ bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
depends on FORCEDETH && EXPERIMENTAL
help
NAPI is a new driver API designed to reduce CPU and interrupt load
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config CS89x0
depends on NET_PCI && PCI && MIPS
select MII
-config DGRS
- tristate "Digi Intl. RightSwitch SE-X support"
- depends on NET_PCI && (PCI || EISA)
- ---help---
- This is support for the Digi International RightSwitch series of
- PCI/EISA Ethernet switch cards. These include the SE-4 and the SE-6
- models. If you have a network card of this type, say Y and read the
- Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. More specific
- information is contained in <file:Documentation/networking/dgrs.txt>.
-
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
- will be called dgrs.
-
config EEPRO100
tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
depends on NET_PCI && PCI
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
config LAN_SAA9730
bool "Philips SAA9730 Ethernet support"
depends on NET_PCI && PCI && MIPS_ATLAS
To compile this driver as a module, choose M here: the module
will be called sc92031. This is recommended.
+config CPMAC
+ tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
+ depends on NET_ETHERNET && EXPERIMENTAL && AR7
+ select PHYLIB
+ select FIXED_PHY
+ select FIXED_MII_100_FDX
+ help
+ TI AR7 CPMAC Ethernet support
+
config NET_POCKET
bool "Pocket and portable adapters"
depends on PARPORT
The safe and default value for this is N.
config DL2K
- tristate "D-Link DL2000-based Gigabit Ethernet support"
+ tristate "DL2000/TC902x-based Gigabit Ethernet support"
depends on PCI
select CRC32
help
- This driver supports D-Link 2000-based gigabit ethernet cards, which
- includes
+ This driver supports DL2000/TC902x-based Gigabit ethernet cards,
+ which includes
D-Link DGE-550T Gigabit Ethernet Adapter.
D-Link DL2000-based Gigabit Ethernet Adapter.
+ Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
To compile this driver as a module, choose M here: the
module will be called dl2k.
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config E1000_DISABLE_PACKET_SPLIT
If in doubt, say N.
+config E1000E
+ tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
+ depends on PCI
+ ---help---
+ This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
+ ethernet family of adapters. For PCI or PCI-X e1000 adapters,
+ use the regular e1000 driver For more information on how to
+ identify your adapter, go to the Adapter & Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/e1000e.txt>.
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module
+ will be called e1000e.
+
source "drivers/net/ixp2000/Kconfig"
config MYRI_SBUS
will be called r8169. This is recommended.
config R8169_NAPI
- bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
+ bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
depends on R8169 && EXPERIMENTAL
help
NAPI is a new driver API designed to reduce CPU and interrupt load
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config R8169_VLAN
If in doubt, say Y.
+config SB1250_MAC
+ tristate "SB1250 Gigabit Ethernet support"
+ depends on SIBYTE_SB1xxx_SOC
+ select PHYLIB
+ ---help---
+ This driver supports Gigabit Ethernet interfaces based on the
+ Broadcom SiByte family of System-On-a-Chip parts. They include
+ the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455
+ and BCM1480 chips.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sb1250-mac.
+
config SIS190
tristate "SiS190/SiS191 gigabit ethernet support"
depends on PCI
To compile this driver as a module, choose M here: the module
will be called skge. This is recommended.
+config SKGE_DEBUG
+ bool "Debugging interface"
+ depends on SKGE && DEBUG_FS
+ help
+ This option adds the ability to dump driver state for debugging.
+ The file debugfs/skge/ethX displays the state of the internal
+ transmit and receive rings.
+
+ If unsure, say N.
+
config SKY2
tristate "SysKonnect Yukon2 support"
depends on PCI
and MPC86xx family of chips, and the FEC on the 8540.
config GFAR_NAPI
- bool "NAPI Support"
+ bool "Use Rx Polling (NAPI)"
depends on GIANFAR
config UCC_GETH
which is available on some Freescale SOCs.
config UGETH_NAPI
- bool "NAPI Support"
+ bool "Use Rx Polling (NAPI)"
depends on UCC_GETH
config UGETH_MAGIC_PACKET
depends on UCC_GETH
config MV643XX_ETH
- tristate "MV-643XX Ethernet support"
- depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32)
+ tristate "Marvell Discovery (643XX) and Orion ethernet support"
+ depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || ARCH_ORION
select MII
help
- This driver supports the gigabit Ethernet on the Marvell MV643XX
- chipset which is used in the Momenco Ocelot C and Jaguar ATX and
- Pegasos II, amongst other PPC and MIPS boards.
+ This driver supports the gigabit ethernet MACs in the
+ Marvell Discovery PPC/MIPS chipset family (MV643XX) and
+ in the Marvell Orion ARM SoC family.
+
+ Some boards that use the Discovery chipset are the Momenco
+ Ocelot C and Jaguar ATX and Pegasos II.
config QLA3XXX
tristate "QLogic QLA3XXX Network Driver Support"
config EHEA
tristate "eHEA Ethernet support"
- depends on IBMEBUS
+ depends on IBMEBUS && INET
select INET_LRO
---help---
This driver supports the IBM pSeries eHEA ethernet adapter.
To compile the driver as a module, choose M here. The module
will be called ehea.
+config IXGBE
+ tristate "Intel(R) 10GbE PCI Express adapters support"
+ depends on PCI
+ ---help---
+ This driver supports Intel(R) 10GbE PCI Express family of
+ adapters. For more information on how to identify your adapter, go
+ to the Adapter & Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/ixgbe.txt>.
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module
+ will be called ixgbe.
+
config IXGB
tristate "Intel(R) PRO/10GbE support"
depends on PCI
---help---
- This driver supports Intel(R) PRO/10GbE family of
- adapters. For more information on how to identify your adapter, go
+ This driver supports Intel(R) PRO/10GbE family of adapters for
+ PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver
+ instead. For more information on how to identify your adapter, go
to the Adapter & Driver ID Guide at:
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config S2IO
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config MYRI10GE
tristate "Myricom Myri-10G Ethernet support"
- depends on PCI
+ depends on PCI && INET
select FW_LOADER
select CRC32
select INET_LRO
help
This enables the support for NetXen's Gigabit Ethernet card.
+config NIU
+ tristate "Sun Neptune 10Gbit Ethernet support"
+ depends on PCI
+ help
+ This enables support for cards based upon Sun's
+ Neptune chipset.
+
config PASEMI_MAC
tristate "PA Semi 1/10Gbit MAC"
depends on PPC64 && PCI
debug_level module parameter (which can also be set after
the driver is loaded through sysfs).
+config TEHUTI
+ tristate "Tehuti Networks 10G Ethernet"
+ depends on PCI
+ help
+ Tehuti Networks 10G Ethernet NIC
+
endif # NETDEV_10000
source "drivers/net/tokenring/Kconfig"
If you want to log kernel messages over the network, enable this.
See <file:Documentation/networking/netconsole.txt> for details.
+config NETCONSOLE_DYNAMIC
+ bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
+ depends on NETCONSOLE && SYSFS && EXPERIMENTAL
+ select CONFIGFS_FS
+ help
+ This option enables the ability to dynamically reconfigure target
+ parameters (interface, IP addresses, port numbers, MAC addresses)
+ at runtime through a userspace interface exported using configfs.
+ See <file:Documentation/networking/netconsole.txt> for details.
+
config NETPOLL
def_bool NETCONSOLE
config NET_POLL_CONTROLLER
def_bool NETPOLL
+config VIRTIO_NET
+ tristate "Virtio network driver (EXPERIMENTAL)"
+ depends on EXPERIMENTAL && VIRTIO
+ ---help---
+ This is the virtual network driver for lguest. Say Y or M.
+
endif # NETDEVICES
projects / linux-2.6-omap-h63xx.git / blobdiff