will be called smc-ultra32.
config BFIN_MAC
- tristate "Blackfin 536/537 on-chip mac support"
- depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
+ tristate "Blackfin 527/536/537 on-chip mac support"
+ depends on NET_ETHERNET && (BF527 || BF537 || BF536) && (!BF537_PORT_H)
select CRC32
select MII
select PHYLIB
config BFIN_MAC_USE_L1
bool "Use L1 memory for rx/tx packets"
- depends on BFIN_MAC && BF537
+ depends on BFIN_MAC && (BF527 || BF537)
default y
help
To get maximum network performance, you should use L1 memory as rx/tx buffers.
config BFIN_MAC_RMII
bool "RMII PHY Interface (EXPERIMENTAL)"
depends on BFIN_MAC && EXPERIMENTAL
- default n
+ default y if BFIN527_EZKIT
+ default n if BFIN537_STAMP
help
Use Reduced PHY MII Interface
tristate "SMC 91C9x/91C1xxx support"
select CRC32
select MII
- depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BLACKFIN
+ depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
+ SOC_AU1X00 || BLACKFIN || MN10300
help
This is a driver for SMC's 91x series of Ethernet chipsets,
including the SMC91C94 and the SMC91C111. Say Y if you want it
To compile this driver as a module, choose M here. The module
will be called dm9000.
+config ENC28J60
+ tristate "ENC28J60 support"
+ depends on EXPERIMENTAL && SPI && NET_ETHERNET
+ select CRC32
+ ---help---
+ Support for the Microchip EN28J60 ethernet chip.
+
+ To compile this driver as a module, choose M here. The module will be
+ called enc28j60.
+
+config ENC28J60_WRITEVERIFY
+ bool "Enable write verify"
+ depends on ENC28J60
+ ---help---
+ Enable the verify after the buffer write useful for debugging purpose.
+ If unsure, say N.
+
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
config IBMLANA
tristate "IBM LAN Adapter/A support"
- depends on MCA && MCA_LEGACY
+ depends on MCA
---help---
This is a Micro Channel Ethernet adapter. You need to set
CONFIG_MCA to use this driver. It is both available as an in-kernel
experience problems, you can enable this option to restore the
old RX-reset behavior. If unsure, say N.
+config R6040
+ tristate "RDC R6040 Fast Ethernet Adapter support (EXPERIMENTAL)"
+ depends on NET_PCI && PCI
+ select CRC32
+ select MII
+ help
+ This is a driver for the R6040 Fast Ethernet MACs found in the
+ the RDC R-321x System-on-chips.
+
+ To compile this driver as a module, choose M here: the module
+ will be called r6040. This is recommended.
+
config SIS900
tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
depends on NET_PCI && PCI
config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
- depends on NET_ETHERNET && EXPERIMENTAL && AR7
+ depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN
select PHYLIB
- select FIXED_PHY
- select FIXED_MII_100_FDX
help
TI AR7 CPMAC Ethernet support
config SGISEEQ
tristate "SGI Seeq ethernet controller support"
- depends on SGI_IP22
+ depends on SGI_HAS_SEEQ
help
Say Y here if you have an Seeq based Ethernet network card. This is
used in many Silicon Graphics machines.
To compile this driver as a module, choose M here. The module
will be called e1000e.
+config E1000E_ENABLED
+ def_bool E1000E != n
+
config IP1000
tristate "IP1000 Gigabit Ethernet support"
depends on PCI && EXPERIMENTAL
To compile this driver as a module, choose M here: the module
will be called ipg. This is recommended.
+config IGB
+ tristate "Intel(R) 82575 PCI-Express Gigabit Ethernet support"
+ depends on PCI
+ ---help---
+ This driver supports Intel(R) 82575 gigabit ethernet family of
+ adapters. For more information on how to identify your adapter, go
+ to the Adapter & Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/e1000.txt>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called igb.
+
source "drivers/net/ixp2000/Kconfig"
config MYRI_SBUS
config GIANFAR
tristate "Gianfar Ethernet"
- depends on 85xx || 83xx || PPC_86xx
+ depends on FSL_SOC
select PHYLIB
select CRC32
help
tristate "PA Semi 1/10Gbit MAC"
depends on PPC64 && PCI
select PHYLIB
+ select INET_LRO
help
This driver supports the on-chip 1/10Gbit Ethernet controller on
PA Semi's PWRficient line of chips.
help
Tehuti Networks 10G Ethernet NIC
+config BNX2X
+ tristate "Broadcom NetXtremeII 10Gb support"
+ depends on PCI
+ select ZLIB_INFLATE
+ help
+ This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
+ To compile this driver as a module, choose M here: the module
+ will be called bnx2x. This is recommended.
+
+
endif # NETDEV_10000
source "drivers/net/tokenring/Kconfig"
adaptor below. You also should have said Y to "SCSI support" and
"SCSI generic support".
-config SHAPER
- tristate "Traffic Shaper (OBSOLETE)"
- depends on EXPERIMENTAL
- ---help---
- The traffic shaper is a virtual network device that allows you to
- limit the rate of outgoing data flow over some other network device.
- The traffic that you want to slow down can then be routed through
- these virtual devices. See
- <file:Documentation/networking/shaper.txt> for more information.
-
- An alternative to this traffic shaper are traffic schedulers which
- you'll get if you say Y to "QoS and/or fair queuing" in
- "Networking options".
-
- To compile this driver as a module, choose M here: the module
- will be called shaper. If unsure, say N.
-
config NETCONSOLE
tristate "Network console logging support (EXPERIMENTAL)"
depends on EXPERIMENTAL
tristate "Virtio network driver (EXPERIMENTAL)"
depends on EXPERIMENTAL && VIRTIO
---help---
- This is the virtual network driver for lguest. Say Y or M.
+ This is the virtual network driver for virtio. It can be used with
+ lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
endif # NETDEVICES