Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik...

[linux-2.6-omap-h63xx.git] / drivers / net / Kconfig

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 4b9b7fe41ee029724999e0db4ea5e006b102d118..43d03178064dfb96f8c7957c328e0d1f2754cea8 100644 (file)
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -25,6 +25,14 @@ menuconfig NETDEVICES
 # that for each of the symbols.
 if NETDEVICES
 
+config NETDEVICES_MULTIQUEUE
+       bool "Netdevice multiple hardware queue support"
+       ---help---
+         Say Y here if you want to allow the network stack to use multiple
+         hardware TX queues on an ethernet device.
+
+         Most people will say N here.
+
 config IFB
        tristate "Intermediate Functional Block support"
        depends on NET_CLS_ACT
@@ -74,6 +82,16 @@ config BONDING
          To compile this driver as a module, choose M here: the module
          will be called bonding.
 
+config MACVLAN
+       tristate "MAC-VLAN support (EXPERIMENTAL)"
+       depends on EXPERIMENTAL
+       ---help---
+         This allows one to create virtual interfaces that map packets to
+         or from specific MAC addresses to a particular interface.
+
+         To compile this driver as a module, choose M here: the module
+         will be called macvlan.
+
 config EQUALIZER
        tristate "EQL (serial line load balancing) support"
        ---help---
@@ -387,22 +405,6 @@ config ATARILANCE
          on the AMD Lance chipset: RieblCard (with or without battery), or
          PAMCard VME (also the version by Rhotron, with different addresses).
 
-config ATARI_BIONET
-       tristate "BioNet-100 support"
-       depends on ATARI && ATARI_ACSI && BROKEN
-       help
-         Say Y to include support for BioData's BioNet-100 Ethernet adapter
-         for the ACSI port. The driver works (has to work...) with a polled
-         I/O scheme, so it's rather slow :-(
-
-config ATARI_PAMSNET
-       tristate "PAMsNet support"
-       depends on ATARI && ATARI_ACSI && BROKEN
-       help
-         Say Y to include support for the PAMsNet Ethernet adapter for the
-         ACSI port ("ACSI node"). The driver works (has to work...) with a
-         polled I/O scheme, so it's rather slow :-(
-
 config SUN3LANCE
        tristate "Sun3/Sun3x on-board LANCE support"
        depends on SUN3 || SUN3X
@@ -586,6 +588,12 @@ config CASSINI
          Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
          <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf>
 
+config SUNVNET
+       tristate "Sun Virtual Network support"
+       depends on SUN_LDOMS
+       help
+         Support for virtual network devices under Sun Logical Domains.
+
 config NET_VENDOR_3COM
        bool "3COM cards"
        depends on ISA || EISA || MCA || PCI
@@ -877,7 +885,7 @@ config NET_NETX
 
 config DM9000
        tristate "DM9000 support"
-       depends on ARM || MIPS
+       depends on ARM || BLACKFIN || MIPS
        select CRC32
        select MII
        ---help---
@@ -2784,6 +2792,19 @@ config PPPOATM
          which can lead to bad results if the ATM peer loses state and
          changes its encapsulation unilaterally.
 
+config PPPOL2TP
+       tristate "PPP over L2TP (EXPERIMENTAL)"
+       depends on EXPERIMENTAL && PPP
+       help
+         Support for PPP-over-L2TP socket family. L2TP is a protocol
+         used by ISPs and enterprises to tunnel PPP traffic over UDP
+         tunnels. L2TP is replacing PPTP for VPN uses.
+
+         This kernel component handles only L2TP data packets: a
+         userland daemon handles L2TP the control protocol (tunnel
+         and session setup). One such daemon is OpenL2TP
+         (http://openl2tp.sourceforge.net/).
+
 config SLIP
        tristate "SLIP (serial line) support"
        ---help---