# that for each of the symbols.
if NETDEVICES
-config NETDEVICES_MULTIQUEUE
- bool "Netdevice multiple hardware queue support"
- ---help---
- Say Y here if you want to allow the network stack to use multiple
- hardware TX queues on an ethernet device.
-
- Most people will say N here.
-
config IFB
tristate "Intermediate Functional Block support"
depends on NET_CLS_ACT
If unsure, say N.
+config SH_ETH
+ tristate "Renesas SuperH Ethernet support"
+ depends on SUPERH && \
+ (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712)
+ select CRC32
+ select MII
+ select MDIO_BITBANG
+ select PHYLIB
+ help
+ Renesas SuperH Ethernet device driver.
+ This driver support SH7710 and SH7712.
+
config SUNLANCE
tristate "Sun LANCE support"
depends on SBUS
To compile this driver as a module, choose M here. The module
will be called dm9000.
+config DM9000_DEBUGLEVEL
+ int "DM9000 maximum debug level"
+ depends on DM9000
+ default 4
+ help
+ The maximum level of debugging code compiled into the DM9000
+ driver.
+
+config DM9000_FORCE_SIMPLE_PHY_POLL
+ bool "Force simple NSR based PHY polling"
+ depends on DM9000
+ ---help---
+ This configuration forces the DM9000 to use the NSR's LinkStatus
+ bit to determine if the link is up or down instead of the more
+ costly MII PHY reads. Note, this will not work if the chip is
+ operating with an external PHY.
+
config ENC28J60
tristate "ENC28J60 support"
depends on EXPERIMENTAL && SPI && NET_ETHERNET
Enable the verify after the buffer write useful for debugging purpose.
If unsure, say N.
-config DM9000_DEBUGLEVEL
- int "DM9000 maximum debug level"
- depends on DM9000
- default 4
- help
- The maximum level of debugging code compiled into the DM9000
- driver.
-
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
select MII
- depends on ARCH_PXA || SH_MAGIC_PANEL_R2
+ depends on ARCH_PXA || SUPERH
help
This is a driver for SMSC's LAN911x series of Ethernet chipsets
including the new LAN9115, LAN9116, LAN9117, and LAN9118.
To compile this driver as a module, choose M here. The module will
be called ibmveth.
-source "drivers/net/ibm_emac/Kconfig"
source "drivers/net/ibm_newemac/Kconfig"
config NET_PCI
To compile this driver as a module, choose M here. The module
will be called amd8111e.
-config AMD8111E_NAPI
- bool "Use RX polling (NAPI)"
- depends on AMD8111_ETH
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config ADAPTEC_STARFIRE
tristate "Adaptec Starfire/DuraLAN support"
depends on NET_PCI && PCI
To compile this driver as a module, choose M here: the module
will be called starfire. This is recommended.
-config ADAPTEC_STARFIRE_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on ADAPTEC_STARFIRE && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config AC3200
tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL
config B44
tristate "Broadcom 440x/47xx ethernet support"
- depends on SSB_POSSIBLE
+ depends on SSB_POSSIBLE && HAS_DMA
select SSB
select MII
help
config TLAN
tristate "TI ThunderLAN support"
- depends on NET_PCI && (PCI || EISA) && !64BIT
+ depends on NET_PCI && (PCI || EISA)
---help---
If you have a PCI Ethernet network card based on the ThunderLAN chip
which is supported by this driver, say Y and read the
If unsure, say Y.
-config VIA_RHINE_NAPI
- bool "Use Rx Polling (NAPI)"
- depends on VIA_RHINE
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
config LAN_SAA9730
bool "Philips SAA9730 Ethernet support"
depends on NET_PCI && PCI && MIPS_ATLAS
To compile this driver as a module, choose M here. The module
will be called e1000e.
-config E1000E_ENABLED
- def_bool E1000E != n
-
config IP1000
tristate "IP1000 Gigabit Ethernet support"
depends on PCI && EXPERIMENTAL
To compile this driver as a module, choose M here: the module
will be called r8169. This is recommended.
-config R8169_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on R8169 && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config R8169_VLAN
bool "VLAN support"
depends on R8169 && VLAN_8021Q
---help---
Say Y here for the r8169 driver to support the functions required
by the kernel 802.1Q code.
-
+
If in doubt, say Y.
config SB1250_MAC
config TIGON3
tristate "Broadcom Tigon3 support"
depends on PCI
+ select PHYLIB
help
This driver supports Broadcom Tigon3 based gigabit Ethernet cards.
This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
and MPC86xx family of chips, and the FEC on the 8540.
-config GFAR_NAPI
- bool "Use Rx Polling (NAPI)"
- depends on GIANFAR
-
config UCC_GETH
tristate "Freescale QE Gigabit Ethernet"
depends on QUICC_ENGINE
Enables support for Chelsio's gigabit Ethernet PCI cards. If you
are using only 10G cards say 'N' here.
-config CHELSIO_T1_NAPI
- bool "Use Rx Polling (NAPI)"
- depends on CHELSIO_T1
- default y
- help
- NAPI is a driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card.
-
config CHELSIO_T3
tristate "Chelsio Communications T3 10Gb Ethernet support"
- depends on PCI
+ depends on PCI && INET
select FW_LOADER
+ select INET_LRO
help
This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
adapters.
config EHEA
tristate "eHEA Ethernet support"
- depends on IBMEBUS && INET && SPARSEMEM && MEMORY_HOTPLUG
+ depends on IBMEBUS && INET && SPARSEMEM
select INET_LRO
---help---
This driver supports the IBM pSeries eHEA ethernet adapter.
config IXGBE
tristate "Intel(R) 10GbE PCI Express adapters support"
- depends on PCI
+ depends on PCI && INET
+ select INET_LRO
---help---
This driver supports Intel(R) 10GbE PCI Express family of
adapters. For more information on how to identify your adapter, go
More specific information on configuring the driver is in
<file:Documentation/networking/s2io.txt>.
-config S2IO_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on S2IO && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config MYRI10GE
tristate "Myricom Myri-10G Ethernet support"
depends on PCI && INET
tristate "Broadcom NetXtremeII 10Gb support"
depends on PCI
select ZLIB_INFLATE
+ select LIBCRC32C
help
This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
To compile this driver as a module, choose M here: the module
projects / linux-2.6-omap-h63xx.git / blobdiff