If unsure, say N.
+config SH_ETH
+ tristate "Renesas SuperH Ethernet support"
+ depends on SUPERH && \
+ (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712)
+ select CRC32
+ select MII
+ select MDIO_BITBANG
+ select PHYLIB
+ help
+ Renesas SuperH Ethernet device driver.
+ This driver support SH7710 and SH7712.
+
config SUNLANCE
tristate "Sun LANCE support"
depends on SBUS
To compile this driver as a module, choose M here. The module
will be called dm9000.
+config DM9000_DEBUGLEVEL
+ int "DM9000 maximum debug level"
+ depends on DM9000
+ default 4
+ help
+ The maximum level of debugging code compiled into the DM9000
+ driver.
+
+config DM9000_FORCE_SIMPLE_PHY_POLL
+ bool "Force simple NSR based PHY polling"
+ depends on DM9000
+ ---help---
+ This configuration forces the DM9000 to use the NSR's LinkStatus
+ bit to determine if the link is up or down instead of the more
+ costly MII PHY reads. Note, this will not work if the chip is
+ operating with an external PHY.
+
config ENC28J60
tristate "ENC28J60 support"
depends on EXPERIMENTAL && SPI && NET_ETHERNET
Enable the verify after the buffer write useful for debugging purpose.
If unsure, say N.
-config DM9000_DEBUGLEVEL
- int "DM9000 maximum debug level"
- depends on DM9000
- default 4
- help
- The maximum level of debugging code compiled into the DM9000
- driver.
-
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
select MII
- depends on ARCH_PXA || SH_MAGIC_PANEL_R2
+ depends on ARCH_PXA || SUPERH
help
This is a driver for SMSC's LAN911x series of Ethernet chipsets
including the new LAN9115, LAN9116, LAN9117, and LAN9118.
To compile this driver as a module, choose M here. The module will
be called ibmveth.
-source "drivers/net/ibm_emac/Kconfig"
source "drivers/net/ibm_newemac/Kconfig"
config NET_PCI
config TLAN
tristate "TI ThunderLAN support"
- depends on NET_PCI && (PCI || EISA) && !64BIT
+ depends on NET_PCI && (PCI || EISA)
---help---
If you have a PCI Ethernet network card based on the ThunderLAN chip
which is supported by this driver, say Y and read the
To compile this driver as a module, choose M here. The module
will be called e1000e.
-config E1000E_ENABLED
- def_bool E1000E != n
-
config IP1000
tristate "IP1000 Gigabit Ethernet support"
depends on PCI && EXPERIMENTAL
To compile this driver as a module, choose M here: the module
will be called r8169. This is recommended.
-config R8169_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on R8169 && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config R8169_VLAN
bool "VLAN support"
depends on R8169 && VLAN_8021Q
---help---
Say Y here for the r8169 driver to support the functions required
by the kernel 802.1Q code.
-
+
If in doubt, say Y.
config SB1250_MAC
config TIGON3
tristate "Broadcom Tigon3 support"
depends on PCI
+ select PHYLIB
help
This driver supports Broadcom Tigon3 based gigabit Ethernet cards.
the driver automatically distinguishes the models, you can
safely enable this option even if you have a wireless-less model.
+config GELIC_WIRELESS_OLD_PSK_INTERFACE
+ bool "PS3 Wireless private PSK interface (OBSOLETE)"
+ depends on GELIC_WIRELESS
+ help
+ This option retains the obsolete private interface to pass
+ the PSK from user space programs to the driver. The PSK
+ stands for 'Pre Shared Key' and is used for WPA[2]-PSK
+ (WPA-Personal) environment.
+ If WPA[2]-PSK is used and you need to use old programs that
+ support only this old interface, say Y. Otherwise N.
+
+ If unsure, say N.
+
config GIANFAR
tristate "Gianfar Ethernet"
depends on FSL_SOC
config CHELSIO_T3
tristate "Chelsio Communications T3 10Gb Ethernet support"
- depends on PCI
+ depends on PCI && INET
select FW_LOADER
+ select INET_LRO
help
This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
adapters.
config EHEA
tristate "eHEA Ethernet support"
- depends on IBMEBUS && INET && SPARSEMEM && MEMORY_HOTPLUG
+ depends on IBMEBUS && INET && SPARSEMEM
select INET_LRO
---help---
This driver supports the IBM pSeries eHEA ethernet adapter.
config IXGBE
tristate "Intel(R) 10GbE PCI Express adapters support"
- depends on PCI
+ depends on PCI && INET
+ select INET_LRO
---help---
This driver supports Intel(R) 10GbE PCI Express family of
adapters. For more information on how to identify your adapter, go
More specific information on configuring the driver is in
<file:Documentation/networking/s2io.txt>.
-config S2IO_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on S2IO && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config MYRI10GE
tristate "Myricom Myri-10G Ethernet support"
depends on PCI && INET
tristate "Broadcom NetXtremeII 10Gb support"
depends on PCI
select ZLIB_INFLATE
+ select LIBCRC32C
help
This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
To compile this driver as a module, choose M here: the module
projects / linux-2.6-omap-h63xx.git / blobdiff