* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
- *
- * $Id: nandsim.c,v 1.8 2005/03/19 15:33:56 dedekind Exp $
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/vmalloc.h>
+#include <asm/div64.h>
#include <linux/slab.h>
#include <linux/errno.h>
#include <linux/string.h>
#include <linux/delay.h>
#include <linux/list.h>
#include <linux/random.h>
+#include <asm/div64.h>
/* Default simulator parameters values */
#if !defined(CONFIG_NANDSIM_FIRST_ID_BYTE) || \
#define STATE_CMD_READID 0x0000000A /* read ID */
#define STATE_CMD_ERASE2 0x0000000B /* sector erase second command */
#define STATE_CMD_RESET 0x0000000C /* reset */
+#define STATE_CMD_RNDOUT 0x0000000D /* random output command */
+#define STATE_CMD_RNDOUTSTART 0x0000000E /* random output start command */
#define STATE_CMD_MASK 0x0000000F /* command states mask */
-/* After an addres is input, the simulator goes to one of these states */
+/* After an address is input, the simulator goes to one of these states */
#define STATE_ADDR_PAGE 0x00000010 /* full (row, column) address is accepted */
#define STATE_ADDR_SEC 0x00000020 /* sector address was accepted */
-#define STATE_ADDR_ZERO 0x00000030 /* one byte zero address was accepted */
-#define STATE_ADDR_MASK 0x00000030 /* address states mask */
+#define STATE_ADDR_COLUMN 0x00000030 /* column address was accepted */
+#define STATE_ADDR_ZERO 0x00000040 /* one byte zero address was accepted */
+#define STATE_ADDR_MASK 0x00000070 /* address states mask */
/* Durind data input/output the simulator is in these states */
#define STATE_DATAIN 0x00000100 /* waiting for data input */
#define ACTION_OOBOFF 0x00600000 /* add to address OOB offset */
#define ACTION_MASK 0x00700000 /* action mask */
-#define NS_OPER_NUM 12 /* Number of operations supported by the simulator */
+#define NS_OPER_NUM 13 /* Number of operations supported by the simulator */
#define NS_OPER_STATES 6 /* Maximum number of states in operation */
#define OPT_ANY 0xFFFFFFFF /* any chip supports this operation */
/* NAND flash "geometry" */
struct nandsin_geometry {
- uint32_t totsz; /* total flash size, bytes */
+ uint64_t totsz; /* total flash size, bytes */
uint32_t secsz; /* flash sector (erase block) size, bytes */
uint pgsz; /* NAND flash page size, bytes */
uint oobsz; /* page OOB area size, bytes */
- uint32_t totszoob; /* total flash size including OOB, bytes */
+ uint64_t totszoob; /* total flash size including OOB, bytes */
uint pgszoob; /* page size including OOB , bytes*/
uint secszoob; /* sector size including OOB, bytes */
uint pgnum; /* total number of pages */
{OPT_ANY, {STATE_CMD_READID, STATE_ADDR_ZERO, STATE_DATAOUT_ID, STATE_READY}},
/* Large page devices read page */
{OPT_LARGEPAGE, {STATE_CMD_READ0, STATE_ADDR_PAGE, STATE_CMD_READSTART | ACTION_CPY,
- STATE_DATAOUT, STATE_READY}}
+ STATE_DATAOUT, STATE_READY}},
+ /* Large page devices random page read */
+ {OPT_LARGEPAGE, {STATE_CMD_RNDOUT, STATE_ADDR_COLUMN, STATE_CMD_RNDOUTSTART | ACTION_CPY,
+ STATE_DATAOUT, STATE_READY}},
};
struct weak_block {
return kstrdup(buf, GFP_KERNEL);
}
+static u_int64_t divide(u_int64_t n, u_int32_t d)
+{
+ do_div(n, d);
+ return n;
+}
+
/*
* Initialize the nandsim structure.
*
struct nand_chip *chip = (struct nand_chip *)mtd->priv;
struct nandsim *ns = (struct nandsim *)(chip->priv);
int i, ret = 0;
- u_int32_t remains;
- u_int32_t next_offset;
+ u_int64_t remains;
+ u_int64_t next_offset;
if (NS_IS_INITIALIZED(ns)) {
NS_ERR("init_nandsim: nandsim is already initialized\n");
ns->geom.oobsz = mtd->oobsize;
ns->geom.secsz = mtd->erasesize;
ns->geom.pgszoob = ns->geom.pgsz + ns->geom.oobsz;
- ns->geom.pgnum = ns->geom.totsz / ns->geom.pgsz;
- ns->geom.totszoob = ns->geom.totsz + ns->geom.pgnum * ns->geom.oobsz;
+ ns->geom.pgnum = divide(ns->geom.totsz, ns->geom.pgsz);
+ ns->geom.totszoob = ns->geom.totsz + (uint64_t)ns->geom.pgnum * ns->geom.oobsz;
ns->geom.secshift = ffs(ns->geom.secsz) - 1;
ns->geom.pgshift = chip->page_shift;
ns->geom.oobshift = ffs(ns->geom.oobsz) - 1;
}
if (ns->options & OPT_SMALLPAGE) {
- if (ns->geom.totsz < (64 << 20)) {
+ if (ns->geom.totsz <= (32 << 20)) {
ns->geom.pgaddrbytes = 3;
ns->geom.secaddrbytes = 2;
} else {
remains = ns->geom.totsz;
next_offset = 0;
for (i = 0; i < parts_num; ++i) {
- unsigned long part = parts[i];
- if (!part || part > remains / ns->geom.secsz) {
+ u_int64_t part_sz = (u_int64_t)parts[i] * ns->geom.secsz;
+
+ if (!part_sz || part_sz > remains) {
NS_ERR("bad partition size.\n");
ret = -EINVAL;
goto error;
}
ns->partitions[i].name = get_partition_name(i);
ns->partitions[i].offset = next_offset;
- ns->partitions[i].size = part * ns->geom.secsz;
+ ns->partitions[i].size = part_sz;
next_offset += ns->partitions[i].size;
remains -= ns->partitions[i].size;
}
if (ns->busw == 16)
NS_WARN("16-bit flashes support wasn't tested\n");
- printk("flash size: %u MiB\n", ns->geom.totsz >> 20);
+ printk("flash size: %llu MiB\n",
+ (unsigned long long)ns->geom.totsz >> 20);
printk("page size: %u bytes\n", ns->geom.pgsz);
printk("OOB area size: %u bytes\n", ns->geom.oobsz);
printk("sector size: %u KiB\n", ns->geom.secsz >> 10);
printk("bus width: %u\n", ns->busw);
printk("bits in sector size: %u\n", ns->geom.secshift);
printk("bits in page size: %u\n", ns->geom.pgshift);
- printk("bits in OOB size: %u\n", ns->geom.oobshift);
- printk("flash size with OOB: %u KiB\n", ns->geom.totszoob >> 10);
+ printk("bits in OOB size: %u\n", ns->geom.oobshift);
+ printk("flash size with OOB: %llu KiB\n",
+ (unsigned long long)ns->geom.totszoob >> 10);
printk("page address bytes: %u\n", ns->geom.pgaddrbytes);
printk("sector address bytes: %u\n", ns->geom.secaddrbytes);
printk("options: %#x\n", ns->options);
if (!rptwear)
return 0;
- wear_eb_count = mtd->size / mtd->erasesize;
+ wear_eb_count = divide(mtd->size, mtd->erasesize);
mem = wear_eb_count * sizeof(unsigned long);
if (mem / sizeof(unsigned long) != wear_eb_count) {
NS_ERR("Too many erase blocks for wear reporting\n");
return "STATE_CMD_ERASE2";
case STATE_CMD_RESET:
return "STATE_CMD_RESET";
+ case STATE_CMD_RNDOUT:
+ return "STATE_CMD_RNDOUT";
+ case STATE_CMD_RNDOUTSTART:
+ return "STATE_CMD_RNDOUTSTART";
case STATE_ADDR_PAGE:
return "STATE_ADDR_PAGE";
case STATE_ADDR_SEC:
return "STATE_ADDR_SEC";
case STATE_ADDR_ZERO:
return "STATE_ADDR_ZERO";
+ case STATE_ADDR_COLUMN:
+ return "STATE_ADDR_COLUMN";
case STATE_DATAIN:
return "STATE_DATAIN";
case STATE_DATAOUT:
switch (cmd) {
case NAND_CMD_READ0:
+ case NAND_CMD_READ1:
case NAND_CMD_READSTART:
case NAND_CMD_PAGEPROG:
case NAND_CMD_READOOB:
case NAND_CMD_READID:
case NAND_CMD_ERASE2:
case NAND_CMD_RESET:
- case NAND_CMD_READ1:
+ case NAND_CMD_RNDOUT:
+ case NAND_CMD_RNDOUTSTART:
return 0;
case NAND_CMD_STATUS_MULTI:
return STATE_CMD_ERASE2;
case NAND_CMD_RESET:
return STATE_CMD_RESET;
+ case NAND_CMD_RNDOUT:
+ return STATE_CMD_RNDOUT;
+ case NAND_CMD_RNDOUTSTART:
+ return STATE_CMD_RNDOUTSTART;
}
NS_ERR("get_state_by_command: unknown command, BUG\n");
mypage = NS_GET_PAGE(ns);
if (mypage->byte == NULL) {
NS_DBG("prog_page: allocating page %d\n", ns->regs.row);
- mypage->byte = kmalloc(ns->geom.pgszoob, GFP_KERNEL);
+ /*
+ * We allocate memory with GFP_NOFS because a flash FS may
+ * utilize this. If it is holding an FS lock, then gets here,
+ * then kmalloc runs writeback which goes to the FS again
+ * and deadlocks. This was seen in practice.
+ */
+ mypage->byte = kmalloc(ns->geom.pgszoob, GFP_NOFS);
if (mypage->byte == NULL) {
NS_ERR("prog_page: error allocating memory for page %d\n", ns->regs.row);
return -1;
ns->regs.num = 1;
break;
+ case STATE_ADDR_COLUMN:
+ /* Column address is always 2 bytes */
+ ns->regs.num = ns->geom.pgaddrbytes - ns->geom.secaddrbytes;
+ break;
+
default:
NS_ERR("switch_state: BUG! unknown address state\n");
}
return;
}
- /*
- * Chip might still be in STATE_DATAOUT
- * (if OPT_AUTOINCR feature is supported), STATE_DATAOUT_STATUS or
- * STATE_DATAOUT_STATUS_M state. If so, switch state.
- */
+ /* Check that the command byte is correct */
+ if (check_command(byte)) {
+ NS_ERR("write_byte: unknown command %#x\n", (uint)byte);
+ return;
+ }
+
if (NS_STATE(ns->state) == STATE_DATAOUT_STATUS
|| NS_STATE(ns->state) == STATE_DATAOUT_STATUS_M
- || ((ns->options & OPT_AUTOINCR) && NS_STATE(ns->state) == STATE_DATAOUT))
+ || NS_STATE(ns->state) == STATE_DATAOUT) {
+ int row = ns->regs.row;
+
switch_state(ns);
+ if (byte == NAND_CMD_RNDOUT)
+ ns->regs.row = row;
+ }
/* Check if chip is expecting command */
if (NS_STATE(ns->nxstate) != STATE_UNKNOWN && !(ns->nxstate & STATE_CMD_MASK)) {
switch_to_ready_state(ns, NS_STATUS_FAILED(ns));
}
- /* Check that the command byte is correct */
- if (check_command(byte)) {
- NS_ERR("write_byte: unknown command %#x\n", (uint)byte);
- return;
- }
-
NS_DBG("command byte corresponding to %s state accepted\n",
get_state_name(get_state_by_command(byte)));
ns->regs.command = byte;
}
if (overridesize) {
- u_int32_t new_size = nsmtd->erasesize << overridesize;
+ u_int64_t new_size = (u_int64_t)nsmtd->erasesize << overridesize;
if (new_size >> overridesize != nsmtd->erasesize) {
NS_ERR("overridesize is too big\n");
goto err_exit;
/* N.B. This relies on nand_scan not doing anything with the size before we change it */
nsmtd->size = new_size;
chip->chipsize = new_size;
- chip->chip_shift = ffs(new_size) - 1;
+ chip->chip_shift = ffs(nsmtd->erasesize) + overridesize - 1;
+ chip->pagemask = (chip->chipsize >> chip->page_shift) - 1;
}
if ((retval = setup_wear_reporting(nsmtd)) != 0)
projects / linux-2.6-omap-h63xx.git / blobdiff