# drivers/mtd/nand/Kconfig
-# $Id: Kconfig,v 1.31 2005/06/20 12:03:21 bjd Exp $
+# $Id: Kconfig,v 1.35 2005/11/07 11:14:30 gleixner Exp $
menu "NAND Flash Device Drivers"
depends on MTD!=n
config MTD_NAND_AUTCPU12
tristate "SmartMediaCard on autronix autcpu12 board"
- depends on ARM && MTD_NAND && ARCH_AUTCPU12
+ depends on MTD_NAND && ARCH_AUTCPU12
help
- This enables the driver for the autronix autcpu12 board to
+ This enables the driver for the autronix autcpu12 board to
access the SmartMediaCard.
config MTD_NAND_EDB7312
tristate "Support for Cirrus Logic EBD7312 evaluation board"
- depends on ARM && MTD_NAND && ARCH_EDB7312
+ depends on MTD_NAND && ARCH_EDB7312
help
- This enables the driver for the Cirrus Logic EBD7312 evaluation
+ This enables the driver for the Cirrus Logic EBD7312 evaluation
board to access the onboard NAND Flash.
config MTD_NAND_H1900
tristate "iPAQ H1900 flash"
- depends on ARM && MTD_NAND && ARCH_PXA && MTD_PARTITIONS
+ depends on MTD_NAND && ARCH_PXA && MTD_PARTITIONS
help
This enables the driver for the iPAQ h1900 flash.
config MTD_NAND_SPIA
tristate "NAND Flash device on SPIA board"
- depends on ARM && ARCH_P720T && MTD_NAND
+ depends on ARCH_P720T && MTD_NAND
help
If you had to ask, you don't have one. Say 'N'.
+config MTD_NAND_AMS_DELTA
+ tristate "NAND Flash device on Amstrad E3"
+ depends on MACH_AMS_DELTA && MTD_NAND
+ help
+ Support for NAND flash on Amstrad E3 (Delta).
+
config MTD_NAND_TOTO
tristate "NAND Flash device on TOTO board"
- depends on ARM && ARCH_OMAP && MTD_NAND
+ depends on ARCH_OMAP && MTD_NAND
help
Support for NAND flash on Texas Instruments Toto platform.
+config MTD_NAND_TS7250
+ tristate "NAND Flash device on TS-7250 board"
+ depends on MACH_TS72XX && MTD_NAND
+ help
+ Support for NAND flash on Technologic Systems TS-7250 platform.
+
config MTD_NAND_IDS
tristate
config MTD_NAND_AU1550
- tristate "Au1550 NAND support"
- depends on SOC_AU1550 && MTD_NAND
+ tristate "Au1550/1200 NAND support"
+ depends on (SOC_AU1200 || SOC_AU1550) && MTD_NAND
help
This enables the driver for the NAND flash controller on the
AMD/Alchemy 1550 SOC.
select REED_SOLOMON
select REED_SOLOMON_DEC8
help
- This enables the driver for the Renesas Technology AG-AND
+ This enables the driver for the Renesas Technology AG-AND
flash interface board (FROM_BOARD4)
config MTD_NAND_PPCHAMELEONEVB
This enables the NAND flash controller on the S3C2410 and S3C2440
SoCs
- No board specfic support is done by this driver, each board
- must advertise a platform_device for the driver to attach.
+ No board specific support is done by this driver, each board
+ must advertise a platform_device for the driver to attach.
config MTD_NAND_S3C2410_DEBUG
bool "S3C2410 NAND driver debug"
Even if you leave this disabled, you can enable BBT writes at module
load time (assuming you build diskonchip as a module) with the module
parameter "inftl_bbt_write=1".
-
- config MTD_NAND_SHARPSL
- bool "Support for NAND Flash on Sharp SL Series (C7xx + others)"
- depends on MTD_NAND && ARCH_PXA
-
- config MTD_NAND_NANDSIM
- bool "Support for NAND Flash Simulator"
- depends on MTD_NAND && MTD_PARTITIONS
+config MTD_NAND_SHARPSL
+ tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
+ depends on MTD_NAND && ARCH_PXA
+
+config MTD_NAND_CS553X
+ tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)"
+ depends on MTD_NAND && X86_PC && PCI
help
- The simulator may simulate verious NAND flash chips for the
+ The CS553x companion chips for the AMD Geode processor
+ include NAND flash controllers with built-in hardware ECC
+ capabilities; enabling this option will allow you to use
+ these. The driver will check the MSRs to verify that the
+ controller is enabled for NAND, and currently requires that
+ the controller be in MMIO mode.
+
+ If you say "m", the module will be called "cs553x_nand.ko".
+
+config MTD_NAND_NANDSIM
+ tristate "Support for NAND Flash Simulator"
+ depends on MTD_NAND && MTD_PARTITIONS
+ help
+ The simulator may simulate various NAND flash chips for the
MTD nand layer.
-
+
endmenu