#include <linux/delay.h>
#include <linux/device.h>
#include <linux/mutex.h>
+#include <linux/err.h>
+
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
* doesn't (yet) use these for any kind of i/o overlap or prefetching.
*
* Sometimes DataFlash is packaged in MMC-format cards, although the
- * MMC stack can't use SPI (yet), or distinguish between MMC and DataFlash
+ * MMC stack can't (yet?) distinguish between MMC and DataFlash
* protocols during enumeration.
*/
-#define CONFIG_DATAFLASH_WRITE_VERIFY
-
/* reads can bypass the buffers */
#define OP_READ_CONTINUOUS 0xE8
#define OP_READ_PAGE 0xD2
*/
#define OP_READ_ID 0x9F
#define OP_READ_SECURITY 0x77
-#define OP_WRITE_SECURITY 0x9A /* OTP bits */
+#define OP_WRITE_SECURITY_REVC 0x9A
+#define OP_WRITE_SECURITY 0x9B /* revision D */
struct dataflash {
- u8 command[4];
+ uint8_t command[4];
char name[24];
unsigned partitioned:1;
struct spi_transfer x = { .tx_dma = 0, };
struct spi_message msg;
unsigned blocksize = priv->page_size << 3;
- u8 *command;
+ uint8_t *command;
DEBUG(MTD_DEBUG_LEVEL2, "%s: erase addr=0x%x len 0x%x\n",
spi->dev.bus_id,
pageaddr = pageaddr << priv->page_offset;
command[0] = do_block ? OP_ERASE_BLOCK : OP_ERASE_PAGE;
- command[1] = (u8)(pageaddr >> 16);
- command[2] = (u8)(pageaddr >> 8);
+ command[1] = (uint8_t)(pageaddr >> 16);
+ command[2] = (uint8_t)(pageaddr >> 8);
command[3] = 0;
DEBUG(MTD_DEBUG_LEVEL3, "ERASE %s: (%x) %x %x %x [%i]\n",
struct spi_transfer x[2] = { { .tx_dma = 0, }, };
struct spi_message msg;
unsigned int addr;
- u8 *command;
+ uint8_t *command;
int status;
DEBUG(MTD_DEBUG_LEVEL2, "%s: read 0x%x..0x%x\n",
* fewer "don't care" bytes. Both buffers stay unchanged.
*/
command[0] = OP_READ_CONTINUOUS;
- command[1] = (u8)(addr >> 16);
- command[2] = (u8)(addr >> 8);
- command[3] = (u8)(addr >> 0);
+ command[1] = (uint8_t)(addr >> 16);
+ command[2] = (uint8_t)(addr >> 8);
+ command[3] = (uint8_t)(addr >> 0);
/* plus 4 "don't care" bytes */
status = spi_sync(priv->spi, &msg);
size_t remaining = len;
u_char *writebuf = (u_char *) buf;
int status = -EINVAL;
- u8 *command;
+ uint8_t *command;
DEBUG(MTD_DEBUG_LEVEL2, "%s: write 0x%x..0x%x\n",
spi->dev.bus_id, (unsigned)to, (unsigned)(to + len));
(void) dataflash_waitready(priv->spi);
-#ifdef CONFIG_DATAFLASH_WRITE_VERIFY
+#ifdef CONFIG_MTD_DATAFLASH_VERIFY_WRITE
/* (3) Compare to Buffer1 */
addr = pageaddr << priv->page_offset;
status = dataflash_waitready(priv->spi);
/* Check result of the compare operation */
- if ((status & (1 << 6)) == 1) {
+ if (status & (1 << 6)) {
printk(KERN_ERR "%s: compare page %u, err %d\n",
spi->dev.bus_id, pageaddr, status);
remaining = 0;
} else
status = 0;
-#endif /* CONFIG_DATAFLASH_WRITE_VERIFY */
+#endif /* CONFIG_MTD_DATAFLASH_VERIFY_WRITE */
remaining = remaining - writelen;
pageaddr++;
/* ......................................................................... */
+#ifdef CONFIG_MTD_DATAFLASH_OTP
+
+static int dataflash_get_otp_info(struct mtd_info *mtd,
+ struct otp_info *info, size_t len)
+{
+ /* Report both blocks as identical: bytes 0..64, locked.
+ * Unless the user block changed from all-ones, we can't
+ * tell whether it's still writable; so we assume it isn't.
+ */
+ info->start = 0;
+ info->length = 64;
+ info->locked = 1;
+ return sizeof(*info);
+}
+
+static ssize_t otp_read(struct spi_device *spi, unsigned base,
+ uint8_t *buf, loff_t off, size_t len)
+{
+ struct spi_message m;
+ size_t l;
+ uint8_t *scratch;
+ struct spi_transfer t;
+ int status;
+
+ if (off > 64)
+ return -EINVAL;
+
+ if ((off + len) > 64)
+ len = 64 - off;
+ if (len == 0)
+ return len;
+
+ spi_message_init(&m);
+
+ l = 4 + base + off + len;
+ scratch = kzalloc(l, GFP_KERNEL);
+ if (!scratch)
+ return -ENOMEM;
+
+ /* OUT: OP_READ_SECURITY, 3 don't-care bytes, zeroes
+ * IN: ignore 4 bytes, data bytes 0..N (max 127)
+ */
+ scratch[0] = OP_READ_SECURITY;
+
+ memset(&t, 0, sizeof t);
+ t.tx_buf = scratch;
+ t.rx_buf = scratch;
+ t.len = l;
+ spi_message_add_tail(&t, &m);
+
+ dataflash_waitready(spi);
+
+ status = spi_sync(spi, &m);
+ if (status >= 0) {
+ memcpy(buf, scratch + 4 + base + off, len);
+ status = len;
+ }
+
+ kfree(scratch);
+ return status;
+}
+
+static int dataflash_read_fact_otp(struct mtd_info *mtd,
+ loff_t from, size_t len, size_t *retlen, u_char *buf)
+{
+ struct dataflash *priv = (struct dataflash *)mtd->priv;
+ int status;
+
+ /* 64 bytes, from 0..63 ... start at 64 on-chip */
+ mutex_lock(&priv->lock);
+ status = otp_read(priv->spi, 64, buf, from, len);
+ mutex_unlock(&priv->lock);
+
+ if (status < 0)
+ return status;
+ *retlen = status;
+ return 0;
+}
+
+static int dataflash_read_user_otp(struct mtd_info *mtd,
+ loff_t from, size_t len, size_t *retlen, u_char *buf)
+{
+ struct dataflash *priv = (struct dataflash *)mtd->priv;
+ int status;
+
+ /* 64 bytes, from 0..63 ... start at 0 on-chip */
+ mutex_lock(&priv->lock);
+ status = otp_read(priv->spi, 0, buf, from, len);
+ mutex_unlock(&priv->lock);
+
+ if (status < 0)
+ return status;
+ *retlen = status;
+ return 0;
+}
+
+static int dataflash_write_user_otp(struct mtd_info *mtd,
+ loff_t from, size_t len, size_t *retlen, u_char *buf)
+{
+ struct spi_message m;
+ const size_t l = 4 + 64;
+ uint8_t *scratch;
+ struct spi_transfer t;
+ struct dataflash *priv = (struct dataflash *)mtd->priv;
+ int status;
+
+ if (len > 64)
+ return -EINVAL;
+
+ /* Strictly speaking, we *could* truncate the write ... but
+ * let's not do that for the only write that's ever possible.
+ */
+ if ((from + len) > 64)
+ return -EINVAL;
+
+ /* OUT: OP_WRITE_SECURITY, 3 zeroes, 64 data-or-zero bytes
+ * IN: ignore all
+ */
+ scratch = kzalloc(l, GFP_KERNEL);
+ if (!scratch)
+ return -ENOMEM;
+ scratch[0] = OP_WRITE_SECURITY;
+ memcpy(scratch + 4 + from, buf, len);
+
+ spi_message_init(&m);
+
+ memset(&t, 0, sizeof t);
+ t.tx_buf = scratch;
+ t.len = l;
+ spi_message_add_tail(&t, &m);
+
+ /* Write the OTP bits, if they've not yet been written.
+ * This modifies SRAM buffer1.
+ */
+ mutex_lock(&priv->lock);
+ dataflash_waitready(priv->spi);
+ status = spi_sync(priv->spi, &m);
+ mutex_unlock(&priv->lock);
+
+ kfree(scratch);
+
+ if (status >= 0) {
+ status = 0;
+ *retlen = len;
+ }
+ return status;
+}
+
+static char *otp_setup(struct mtd_info *device, char revision)
+{
+ device->get_fact_prot_info = dataflash_get_otp_info;
+ device->read_fact_prot_reg = dataflash_read_fact_otp;
+ device->get_user_prot_info = dataflash_get_otp_info;
+ device->read_user_prot_reg = dataflash_read_user_otp;
+
+ /* rev c parts (at45db321c and at45db1281 only!) use a
+ * different write procedure; not (yet?) implemented.
+ */
+ if (revision > 'c')
+ device->write_user_prot_reg = dataflash_write_user_otp;
+
+ return ", OTP";
+}
+
+#else
+
+static char *otp_setup(struct mtd_info *device, char revision)
+{
+ return " (OTP)";
+}
+
+#endif
+
+/* ......................................................................... */
+
/*
* Register DataFlash device with MTD subsystem.
*/
static int __devinit
-add_dataflash(struct spi_device *spi, char *name,
- int nr_pages, int pagesize, int pageoffset)
+add_dataflash_otp(struct spi_device *spi, char *name,
+ int nr_pages, int pagesize, int pageoffset, char revision)
{
struct dataflash *priv;
struct mtd_info *device;
struct flash_platform_data *pdata = spi->dev.platform_data;
+ char *otp_tag = "";
priv = kzalloc(sizeof *priv, GFP_KERNEL);
if (!priv)
device->write = dataflash_write;
device->priv = priv;
- dev_info(&spi->dev, "%s (%d KBytes)\n", name, device->size/1024);
+ if (revision >= 'c')
+ otp_tag = otp_setup(device, revision);
+
+ dev_info(&spi->dev, "%s (%d KBytes) pagesize %d bytes%s\n",
+ name, DIV_ROUND_UP(device->size, 1024),
+ pagesize, otp_tag);
dev_set_drvdata(&spi->dev, priv);
if (mtd_has_partitions()) {
return add_mtd_device(device) == 1 ? -ENODEV : 0;
}
+static inline int __devinit
+add_dataflash(struct spi_device *spi, char *name,
+ int nr_pages, int pagesize, int pageoffset)
+{
+ return add_dataflash_otp(spi, name, nr_pages, pagesize,
+ pageoffset, 0);
+}
+
+struct flash_info {
+ char *name;
+
+ /* JEDEC id has a high byte of zero plus three data bytes:
+ * the manufacturer id, then a two byte device id.
+ */
+ uint32_t jedec_id;
+
+ /* The size listed here is what works with OP_ERASE_PAGE. */
+ unsigned nr_pages;
+ uint16_t pagesize;
+ uint16_t pageoffset;
+
+ uint16_t flags;
+#define SUP_POW2PS 0x0002 /* supports 2^N byte pages */
+#define IS_POW2PS 0x0001 /* uses 2^N byte pages */
+};
+
+static struct flash_info __devinitdata dataflash_data [] = {
+
+ /*
+ * NOTE: chips with SUP_POW2PS (rev D and up) need two entries,
+ * one with IS_POW2PS and the other without. The entry with the
+ * non-2^N byte page size can't name exact chip revisions without
+ * losing backwards compatibility for cmdlinepart.
+ *
+ * These newer chips also support 128-byte security registers (with
+ * 64 bytes one-time-programmable) and software write-protection.
+ */
+ { "AT45DB011B", 0x1f2200, 512, 264, 9, SUP_POW2PS},
+ { "at45db011d", 0x1f2200, 512, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB021B", 0x1f2300, 1024, 264, 9, SUP_POW2PS},
+ { "at45db021d", 0x1f2300, 1024, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB041x", 0x1f2400, 2048, 264, 9, SUP_POW2PS},
+ { "at45db041d", 0x1f2400, 2048, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB081B", 0x1f2500, 4096, 264, 9, SUP_POW2PS},
+ { "at45db081d", 0x1f2500, 4096, 256, 8, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB161x", 0x1f2600, 4096, 528, 10, SUP_POW2PS},
+ { "at45db161d", 0x1f2600, 4096, 512, 9, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB321x", 0x1f2700, 8192, 528, 10, 0}, /* rev C */
+
+ { "AT45DB321x", 0x1f2701, 8192, 528, 10, SUP_POW2PS},
+ { "at45db321d", 0x1f2701, 8192, 512, 9, SUP_POW2PS | IS_POW2PS},
+
+ { "AT45DB642x", 0x1f2800, 8192, 1056, 11, SUP_POW2PS},
+ { "at45db642d", 0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS},
+};
+
+static struct flash_info *__devinit jedec_probe(struct spi_device *spi)
+{
+ int tmp;
+ uint8_t code = OP_READ_ID;
+ uint8_t id[3];
+ uint32_t jedec;
+ struct flash_info *info;
+ int status;
+
+ /* JEDEC also defines an optional "extended device information"
+ * string for after vendor-specific data, after the three bytes
+ * we use here. Supporting some chips might require using it.
+ *
+ * If the vendor ID isn't Atmel's (0x1f), assume this call failed.
+ * That's not an error; only rev C and newer chips handle it, and
+ * only Atmel sells these chips.
+ */
+ tmp = spi_write_then_read(spi, &code, 1, id, 3);
+ if (tmp < 0) {
+ DEBUG(MTD_DEBUG_LEVEL0, "%s: error %d reading JEDEC ID\n",
+ spi->dev.bus_id, tmp);
+ return ERR_PTR(tmp);
+ }
+ if (id[0] != 0x1f)
+ return NULL;
+
+ jedec = id[0];
+ jedec = jedec << 8;
+ jedec |= id[1];
+ jedec = jedec << 8;
+ jedec |= id[2];
+
+ for (tmp = 0, info = dataflash_data;
+ tmp < ARRAY_SIZE(dataflash_data);
+ tmp++, info++) {
+ if (info->jedec_id == jedec) {
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: OTP, sector protect%s\n",
+ dev_name(&spi->dev),
+ (info->flags & SUP_POW2PS)
+ ? ", binary pagesize" : ""
+ );
+ if (info->flags & SUP_POW2PS) {
+ status = dataflash_status(spi);
+ if (status < 0) {
+ DEBUG(MTD_DEBUG_LEVEL1,
+ "%s: status error %d\n",
+ dev_name(&spi->dev), status);
+ return ERR_PTR(status);
+ }
+ if (status & 0x1) {
+ if (info->flags & IS_POW2PS)
+ return info;
+ } else {
+ if (!(info->flags & IS_POW2PS))
+ return info;
+ }
+ }
+ }
+ }
+
+ /*
+ * Treat other chips as errors ... we won't know the right page
+ * size (it might be binary) even when we can tell which density
+ * class is involved (legacy chip id scheme).
+ */
+ dev_warn(&spi->dev, "JEDEC id %06x not handled\n", jedec);
+ return ERR_PTR(-ENODEV);
+}
+
/*
- * Detect and initialize DataFlash device:
+ * Detect and initialize DataFlash device, using JEDEC IDs on newer chips
+ * or else the ID code embedded in the status bits:
*
* Device Density ID code #Pages PageSize Offset
* AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9
- * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1025 264 9
+ * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1024 264 9
* AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9
* AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9
* AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10
static int __devinit dataflash_probe(struct spi_device *spi)
{
int status;
-
+ struct flash_info *info;
+
+ /*
+ * Try to detect dataflash by JEDEC ID.
+ * If it succeeds we know we have either a C or D part.
+ * D will support power of 2 pagesize option.
+ * Both support the security register, though with different
+ * write procedures.
+ */
+ info = jedec_probe(spi);
+ if (IS_ERR(info))
+ return PTR_ERR(info);
+ if (info != NULL)
+ return add_dataflash_otp(spi, info->name, info->nr_pages,
+ info->pagesize, info->pageoffset,
+ (info->flags & SUP_POW2PS) ? 'd' : 'c');
+
+ /*
+ * Older chips support only legacy commands, identifing
+ * capacity using bits in the status byte.
+ */
status = dataflash_status(spi);
if (status <= 0 || status == 0xff) {
DEBUG(MTD_DEBUG_LEVEL1, "%s: status error %d\n",
status = add_dataflash(spi, "AT45DB011B", 512, 264, 9);
break;
case 0x14: /* 0 1 0 1 x x */
- status = add_dataflash(spi, "AT45DB021B", 1025, 264, 9);
+ status = add_dataflash(spi, "AT45DB021B", 1024, 264, 9);
break;
case 0x1c: /* 0 1 1 1 x x */
status = add_dataflash(spi, "AT45DB041x", 2048, 264, 9);