else
mask = SDHCI_SPACE_AVAILABLE;
+ /*
+ * Some controllers (JMicron JMB38x) mess up the buffer bits
+ * for transfers < 4 bytes. As long as it is just one block,
+ * we can ignore the bits.
+ */
+ if ((host->quirks & SDHCI_QUIRK_BROKEN_SMALL_PIO) &&
+ (host->data->blocks == 1))
+ mask = ~0;
+
while (readl(host->ioaddr + SDHCI_PRESENT_STATE) & mask) {
if (host->data->flags & MMC_DATA_READ)
sdhci_read_block_pio(host);
host->align_addr = dma_map_single(mmc_dev(host->mmc),
host->align_buffer, 128 * 4, direction);
- if (dma_mapping_error(host->align_addr))
+ if (dma_mapping_error(mmc_dev(host->mmc), host->align_addr))
goto fail;
BUG_ON(host->align_addr & 0x3);
host->adma_addr = dma_map_single(mmc_dev(host->mmc),
host->adma_desc, (128 * 2 + 1) * 4, DMA_TO_DEVICE);
- if (dma_mapping_error(host->align_addr))
+ if (dma_mapping_error(mmc_dev(host->mmc), host->adma_addr))
goto unmap_entries;
BUG_ON(host->adma_addr & 0x3);
* us an invalid request.
*/
WARN_ON(1);
- host->flags &= ~SDHCI_USE_DMA;
+ host->flags &= ~SDHCI_REQ_USE_DMA;
} else {
writel(host->adma_addr,
host->ioaddr + SDHCI_ADMA_ADDRESS);
* us an invalid request.
*/
WARN_ON(1);
- host->flags &= ~SDHCI_USE_DMA;
+ host->flags &= ~SDHCI_REQ_USE_DMA;
} else {
WARN_ON(sg_cnt != 1);
writel(sg_dma_address(data->sg),
SDHCI_INT_INDEX))
host->cmd->error = -EILSEQ;
- if (host->cmd->error)
+ if (host->cmd->error) {
tasklet_schedule(&host->finish_tasklet);
- else if (intmask & SDHCI_INT_RESPONSE)
+ return;
+ }
+
+ /*
+ * The host can send and interrupt when the busy state has
+ * ended, allowing us to wait without wasting CPU cycles.
+ * Unfortunately this is overloaded on the "data complete"
+ * interrupt, so we need to take some care when handling
+ * it.
+ *
+ * Note: The 1.0 specification is a bit ambiguous about this
+ * feature so there might be some problems with older
+ * controllers.
+ */
+ if (host->cmd->flags & MMC_RSP_BUSY) {
+ if (host->cmd->data)
+ DBG("Cannot wait for busy signal when also "
+ "doing a data transfer");
+ else
+ return;
+ }
+
+ if (intmask & SDHCI_INT_RESPONSE)
sdhci_finish_command(host);
}
if (!host->data) {
/*
- * A data end interrupt is sent together with the response
- * for the stop command.
+ * The "data complete" interrupt is also used to
+ * indicate that a busy state has ended. See comment
+ * above in sdhci_cmd_irq().
*/
- if (intmask & SDHCI_INT_DATA_END)
- return;
+ if (host->cmd && (host->cmd->flags & MMC_RSP_BUSY)) {
+ if (intmask & SDHCI_INT_DATA_END) {
+ sdhci_finish_command(host);
+ return;
+ }
+ }
printk(KERN_ERR "%s: Got data interrupt 0x%08x even "
"though no data operation was in progress.\n",