menuconfig NEW_LEDS
bool "LED Support"
- depends on HAS_IOMEM
help
Say Y to enable Linux LED support. This allows control of supported
LEDs from both userspace and optionally, by kernel events (triggers).
comment "LED drivers"
+config LEDS_ATMEL_PWM
+ tristate "LED Support using Atmel PWM outputs"
+ depends on LEDS_CLASS && ATMEL_PWM
+ help
+ This option enables support for LEDs driven using outputs
+ of the dedicated PWM controller found on newer Atmel SOCs.
+
config LEDS_CORGI
tristate "LED Support for the Sharp SL-C7x0 series"
depends on LEDS_CLASS && PXA_SHARP_C7xx
This option enables support for the LEDs on Sharp Zaurus
SL-Cxx00 series (C1000, C3000, C3100).
-config LEDS_IXP4XX
- tristate "LED Support for GPIO connected LEDs on IXP4XX processors"
- depends on LEDS_CLASS && ARCH_IXP4XX
- help
- This option enables support for the LEDs connected to GPIO
- outputs of the Intel IXP4XX processors. To be useful the
- particular board must have LEDs and they must be connected
- to the GPIO lines. If unsure, say Y.
-
-config LEDS_TOSA
- tristate "LED Support for the Sharp SL-6000 series"
- depends on LEDS_CLASS && PXA_SHARPSL
- help
- This option enables support for the LEDs on Sharp Zaurus
- SL-6000 series.
-
config LEDS_S3C24XX
tristate "LED Support for Samsung S3C24XX GPIO LEDs"
depends on LEDS_CLASS && ARCH_S3C2410
help
This option enables support for the PCEngines WRAP programmable LEDs.
+config LEDS_OMAP_DEBUG
+ boolean "LED Support for OMAP debug board LEDs"
+ depends on LEDS_CLASS=y && ARCH_OMAP
+ help
+ Enables support for the LEDs on the debug board used with OMAP
+ reference boards like H2/H3/H4 and Perseus2. Up to six of these
+ may be claimed by the original ARM debug LED API.
+
+config LEDS_OMAP
+ tristate "LED Support for OMAP GPIO LEDs"
+ depends on LEDS_CLASS && ARCH_OMAP
+ help
+ This option enables support for the LEDs on OMAP processors.
+
+config LEDS_OMAP_PWM
+ tristate "LED Support for OMAP PWM-controlled LEDs"
+ depends on LEDS_CLASS && ARCH_OMAP && OMAP_DM_TIMER
+ help
+ This options enables support for LEDs connected to GPIO lines
+ controlled by a PWM timer on OMAP CPUs.
+
config LEDS_H1940
tristate "LED Support for iPAQ H1940 device"
depends on LEDS_CLASS && ARCH_H1940
help
This option enables support for the Cobalt Raq series LEDs.
+config LEDS_HP6XX
+ tristate "LED Support for the HP Jornada 6xx"
+ depends on LEDS_CLASS && SH_HP6XX
+ help
+ This option enables led support for the handheld
+ HP Jornada 620/660/680/690.
+
config LEDS_GPIO
tristate "LED Support for GPIO connected LEDs"
depends on LEDS_CLASS && GENERIC_GPIO
programs through the leds subsystem. This LED have three
known mode: off, blink at 0.5Hz and blink at 1Hz.
- As this LED cannot change it's brightness it blinks instead.
- The brightness value 0 means off, 1..127 means blink at 0.5Hz
- and 128..255 means blink at 1Hz.
+ The driver supports two kinds of interface: using ledtrig-timer
+ or through /sys/class/leds/clevo::mail/brightness. As this LED
+ cannot change it's brightness it blinks instead. The brightness
+ value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
+ blink at 1Hz.
This module can drive the mail LED for the following notebooks:
depends on LEDS_TRIGGERS
help
This allows LEDs to be controlled by a programmable timer
- via sysfs. If unsure, say Y.
+ via sysfs. Some LED hardware can be programmed to start
+ blinking the LED without any further software interaction.
+ For more details read Documentation/leds-class.txt.
+
+ If unsure, say Y.
config LEDS_TRIGGER_IDE_DISK
bool "LED IDE Disk Trigger"