* If rewrite is true, and bits are set in the sendbufferror registers,
* we'll write to the buffer, for error recovery on parity errors.
*/
-void ipath_disarm_senderrbufs(struct ipath_devdata *dd, int rewrite)
+static void ipath_disarm_senderrbufs(struct ipath_devdata *dd, int rewrite)
{
u32 piobcnt;
unsigned long sbuf[4];
* Flush all queued sends when link went to DOWN or INIT,
* to be sure that they don't block SMA and other MAD packets
*/
- ipath_cancel_sends(dd);
+ ipath_cancel_sends(dd, 1);
}
else if (lstate == IPATH_IBSTATE_INIT || lstate == IPATH_IBSTATE_ARM ||
lstate == IPATH_IBSTATE_ACTIVE) {
supp_msgs = handle_frequent_errors(dd, errs, msg, &noprint);
- /*
- * don't report errors that are masked (includes those always
- * ignored)
- */
+ /* don't report errors that are masked */
errs &= ~dd->ipath_maskederrs;
/* do these first, they are most important */
* ones on this particular interrupt, which also isn't great
*/
dd->ipath_maskederrs |= dd->ipath_lasterror | errs;
+ dd->ipath_errormask &= ~dd->ipath_maskederrs;
ipath_write_kreg(dd, dd->ipath_kregs->kr_errormask,
- ~dd->ipath_maskederrs);
+ dd->ipath_errormask);
s_iserr = ipath_decode_err(msg, sizeof msg,
- (dd->ipath_maskederrs & ~dd->
- ipath_ignorederrs));
+ dd->ipath_maskederrs);
- if ((dd->ipath_maskederrs & ~dd->ipath_ignorederrs) &
+ if (dd->ipath_maskederrs &
~(INFINIPATH_E_RRCVEGRFULL |
INFINIPATH_E_RRCVHDRFULL | INFINIPATH_E_PKTERRS))
ipath_dev_err(dd, "Temporarily disabling "
"error(s) %llx reporting; too frequent (%s)\n",
- (unsigned long long) (dd->ipath_maskederrs &
- ~dd->ipath_ignorederrs), msg);
+ (unsigned long long)dd->ipath_maskederrs,
+ msg);
else {
/*
* rcvegrfull and rcvhdrqfull are "normal",
chkerrpkts = 1;
dd->ipath_lastrcvhdrqtails[i] = tl;
pd->port_hdrqfull++;
- if (test_bit(IPATH_PORT_WAITING_OVERFLOW,
- &pd->port_flag)) {
- clear_bit(
- IPATH_PORT_WAITING_OVERFLOW,
- &pd->port_flag);
- set_bit(
- IPATH_PORT_WAITING_OVERFLOW,
- &pd->int_flag);
- wake_up_interruptible(
- &pd->port_wait);
- }
+ /* flush hdrqfull so that poll() sees it */
+ wmb();
+ wake_up_interruptible(&pd->port_wait);
}
}
}
/* disable error interrupts, to avoid confusion */
ipath_write_kreg(dd, dd->ipath_kregs->kr_errormask, 0ULL);
+ /* also disable interrupts; errormask is sometimes overwriten */
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_intmask, 0ULL);
+
/*
* clear all sends, because they have may been
* completed by usercode while in freeze mode, and
* therefore would not be sent, and eventually
* might cause the process to run out of bufs
*/
- ipath_cancel_sends(dd);
+ ipath_cancel_sends(dd, 0);
ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
dd->ipath_control);
/* ensure pio avail updates continue */
ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
- dd->ipath_sendctrl & ~IPATH_S_PIOBUFAVAILUPD);
+ dd->ipath_sendctrl & ~INFINIPATH_S_PIOBUFAVAILUPD);
ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
dd->ipath_sendctrl);
for (i = 0; i < dd->ipath_pioavregs; i++) {
/* deal with 6110 chip bug */
im = i > 3 ? ((i&1) ? i-1 : i+1) : i;
- val = ipath_read_kreg64(dd, 0x1000+(im*sizeof(u64)));
+ val = ipath_read_kreg64(dd, (0x1000/sizeof(u64))+im);
dd->ipath_pioavailregs_dma[i] = dd->ipath_pioavailshadow[i]
= le64_to_cpu(val);
}
ipath_write_kreg(dd, dd->ipath_kregs->kr_errorclear,
E_SPKT_ERRS_IGNORE);
ipath_write_kreg(dd, dd->ipath_kregs->kr_errormask,
- ~dd->ipath_maskederrs);
+ dd->ipath_errormask);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_intmask, -1LL);
ipath_write_kreg(dd, dd->ipath_kregs->kr_intclear, 0ULL);
}
int i;
int rcvdint = 0;
+ /* test_bit below needs this... */
+ rmb();
portr = ((istat >> INFINIPATH_I_RCVAVAIL_SHIFT) &
dd->ipath_i_rcvavail_mask)
| ((istat >> INFINIPATH_I_RCVURG_SHIFT) &
for (i = 1; i < dd->ipath_cfgports; i++) {
struct ipath_portdata *pd = dd->ipath_pd[i];
if (portr & (1 << i) && pd && pd->port_cnt) {
- if (test_bit(IPATH_PORT_WAITING_RCV,
- &pd->port_flag)) {
- clear_bit(IPATH_PORT_WAITING_RCV,
- &pd->port_flag);
- set_bit(IPATH_PORT_WAITING_RCV,
- &pd->int_flag);
+ if (test_and_clear_bit(IPATH_PORT_WAITING_RCV,
+ &pd->port_flag)) {
clear_bit(i + INFINIPATH_R_INTRAVAIL_SHIFT,
&dd->ipath_rcvctrl);
wake_up_interruptible(&pd->port_wait);
rcvdint = 1;
- } else if (test_bit(IPATH_PORT_WAITING_URG,
- &pd->port_flag)) {
- clear_bit(IPATH_PORT_WAITING_URG,
- &pd->port_flag);
- set_bit(IPATH_PORT_WAITING_URG,
- &pd->int_flag);
+ } else if (test_and_clear_bit(IPATH_PORT_WAITING_URG,
+ &pd->port_flag)) {
+ pd->port_urgent++;
wake_up_interruptible(&pd->port_wait);
}
}
u32 istat, chk0rcv = 0;
ipath_err_t estat = 0;
irqreturn_t ret;
- u32 oldhead, curtail;
static unsigned unexpected = 0;
static const u32 port0rbits = (1U<<INFINIPATH_I_RCVAVAIL_SHIFT) |
(1U<<INFINIPATH_I_RCVURG_SHIFT);
goto bail;
}
- /*
- * We try to avoid reading the interrupt status register, since
- * that's a PIO read, and stalls the processor for up to about
- * ~0.25 usec. The idea is that if we processed a port0 packet,
- * we blindly clear the port 0 receive interrupt bits, and nothing
- * else, then return. If other interrupts are pending, the chip
- * will re-interrupt us as soon as we write the intclear register.
- * We then won't process any more kernel packets (if not the 2nd
- * time, then the 3rd or 4th) and we'll then handle the other
- * interrupts. We clear the interrupts first so that we don't
- * lose intr for later packets that arrive while we are processing.
- */
- oldhead = dd->ipath_port0head;
- curtail = (u32)le64_to_cpu(*dd->ipath_hdrqtailptr);
- if (oldhead != curtail) {
- if (dd->ipath_flags & IPATH_GPIO_INTR) {
- ipath_write_kreg(dd, dd->ipath_kregs->kr_gpio_clear,
- (u64) (1 << IPATH_GPIO_PORT0_BIT));
- istat = port0rbits | INFINIPATH_I_GPIO;
- }
- else
- istat = port0rbits;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_intclear, istat);
- ipath_kreceive(dd);
- if (oldhead != dd->ipath_port0head) {
- ipath_stats.sps_fastrcvint++;
- goto done;
- }
- }
-
istat = ipath_read_kreg32(dd, dd->ipath_kregs->kr_intstatus);
if (unlikely(!istat)) {
* GPIO_2 indicates (on some HT4xx boards) that a packet
* has arrived for Port 0. Checking for this
* is controlled by flag IPATH_GPIO_INTR.
- * GPIO_3..5 on IBA6120 Rev2 chips indicate errors
- * that we need to count. Checking for this
+ * GPIO_3..5 on IBA6120 Rev2 and IBA6110 Rev4 chips indicate
+ * errors that we need to count. Checking for this
* is controlled by flag IPATH_GPIO_ERRINTRS.
*/
u32 gpiostatus;
handle_layer_pioavail(dd);
}
-done:
ret = IRQ_HANDLED;
bail:
projects / linux-2.6-omap-h63xx.git / blobdiff