#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/delay.h>
-
+#include <rdma/ib_verbs.h>
#include "ipath_kernel.h"
#include "ipath_registers.h"
.cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt)
};
+/* kr_control bits */
+#define INFINIPATH_C_RESET 1U
+
/* kr_intstatus, kr_intclear, kr_intmask bits */
#define INFINIPATH_I_RCVURG_MASK ((1U<<5)-1)
#define INFINIPATH_I_RCVAVAIL_MASK ((1U<<5)-1)
#define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000
#define INFINIPATH_EXTS_MEMBIST_FOUND 0x0000000000008000
+/* kr_xgxsconfig bits */
+#define INFINIPATH_XGXS_RESET 0x5ULL
+
#define _IPATH_GPIO_SDA_NUM 1
#define _IPATH_GPIO_SCL_NUM 0
#define IPATH_GPIO_SCL (1ULL << \
(_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
+#define INFINIPATH_RT_BUFSIZE_MASK 0xe0000000ULL
+#define INFINIPATH_RT_BUFSIZE_SHIFTVAL(tid) \
+ ((((tid) & INFINIPATH_RT_BUFSIZE_MASK) >> 29) + 11 - 1)
+#define INFINIPATH_RT_BUFSIZE(tid) (1 << INFINIPATH_RT_BUFSIZE_SHIFTVAL(tid))
+#define INFINIPATH_RT_IS_VALID(tid) \
+ (((tid) & INFINIPATH_RT_BUFSIZE_MASK) && \
+ ((((tid) & INFINIPATH_RT_BUFSIZE_MASK) != INFINIPATH_RT_BUFSIZE_MASK)))
+#define INFINIPATH_RT_ADDR_MASK 0x1FFFFFFFULL /* 29 bits valid */
+#define INFINIPATH_RT_ADDR_SHIFT 10
+
#define INFINIPATH_R_INTRAVAIL_SHIFT 16
#define INFINIPATH_R_TAILUPD_SHIFT 31
#define TXE_PIO_PARITY ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | \
INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) \
<< INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)
+#define RXE_EAGER_PARITY (INFINIPATH_HWE_RXEMEMPARITYERR_EAGERTID \
+ << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT)
static void ipath_pe_put_tid_2(struct ipath_devdata *, u64 __iomem *,
u32, unsigned long);
* make sure we get this much out, unless told to be quiet,
* or it's occurred within the last 5 seconds
*/
- if ((hwerrs & ~(dd->ipath_lasthwerror |
- ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF |
- INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC)
- << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT))) ||
+ if ((hwerrs & ~(dd->ipath_lasthwerror | TXE_PIO_PARITY |
+ RXE_EAGER_PARITY)) ||
(ipath_debug & __IPATH_VERBDBG))
dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx "
"(cleared)\n", (unsigned long long) hwerrs);
dd->ipath_f_put_tid = ipath_pe_put_tid_2;
}
-
/*
* set here, not in ipath_init_*_funcs because we have to do
* it after we can read chip registers.
extctl = dd->ipath_extctrl & ~(INFINIPATH_EXTC_LED1PRIPORT_ON |
INFINIPATH_EXTC_LED2PRIPORT_ON);
- if (ltst & INFINIPATH_IBCS_LT_STATE_LINKUP)
+ if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON;
if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON;
pci_disable_msi(dd->pcidev);
}
+static void ipath_6120_pcie_params(struct ipath_devdata *dd)
+{
+ u16 linkstat, speed;
+ int pos;
+
+ pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_EXP);
+ if (!pos) {
+ ipath_dev_err(dd, "Can't find PCI Express capability!\n");
+ goto bail;
+ }
+
+ pci_read_config_word(dd->pcidev, pos + PCI_EXP_LNKSTA,
+ &linkstat);
+ /*
+ * speed is bits 0-4, linkwidth is bits 4-8
+ * no defines for them in headers
+ */
+ speed = linkstat & 0xf;
+ linkstat >>= 4;
+ linkstat &= 0x1f;
+ dd->ipath_lbus_width = linkstat;
+
+ switch (speed) {
+ case 1:
+ dd->ipath_lbus_speed = 2500; /* Gen1, 2.5GHz */
+ break;
+ case 2:
+ dd->ipath_lbus_speed = 5000; /* Gen1, 5GHz */
+ break;
+ default: /* not defined, assume gen1 */
+ dd->ipath_lbus_speed = 2500;
+ break;
+ }
+
+ if (linkstat < 8)
+ ipath_dev_err(dd,
+ "PCIe width %u (x8 HCA), performance reduced\n",
+ linkstat);
+ else
+ ipath_cdbg(VERBOSE, "PCIe speed %u width %u (x8 HCA)\n",
+ dd->ipath_lbus_speed, linkstat);
+
+ if (speed != 1)
+ ipath_dev_err(dd,
+ "PCIe linkspeed %u is incorrect; "
+ "should be 1 (2500)!\n", speed);
+bail:
+ /* fill in string, even on errors */
+ snprintf(dd->ipath_lbus_info, sizeof(dd->ipath_lbus_info),
+ "PCIe,%uMHz,x%u\n",
+ dd->ipath_lbus_speed,
+ dd->ipath_lbus_width);
+
+ return;
+}
+
/**
* ipath_setup_pe_config - setup PCIe config related stuff
* @dd: the infinipath device
} else
ipath_dev_err(dd, "Can't find MSI capability, "
"can't save MSI settings for reset\n");
- if ((pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_EXP))) {
- u16 linkstat;
- pci_read_config_word(dd->pcidev, pos + PCI_EXP_LNKSTA,
- &linkstat);
- linkstat >>= 4;
- linkstat &= 0x1f;
- if (linkstat != 8)
- ipath_dev_err(dd, "PCIe width %u, "
- "performance reduced\n", linkstat);
- }
- else
- ipath_dev_err(dd, "Can't find PCI Express "
- "capability!\n");
+
+ ipath_6120_pcie_params(dd);
dd->ipath_link_width_supported = IB_WIDTH_1X | IB_WIDTH_4X;
dd->ipath_link_speed_supported = IPATH_IB_SDR;
ret = 0; /* failed */
bail:
+ if (ret)
+ ipath_6120_pcie_params(dd);
return ret;
}
}
pa >>= 11;
/* paranoia check */
- if (pa & (7<<29))
+ if (pa & ~INFINIPATH_RT_ADDR_MASK)
ipath_dev_err(dd,
"BUG: Physical page address 0x%lx "
"has bits set in 31-29\n", pa);
}
pa >>= 11;
/* paranoia check */
- if (pa & (7<<29))
+ if (pa & ~INFINIPATH_RT_ADDR_MASK)
ipath_dev_err(dd,
"BUG: Physical page address 0x%lx "
"has bits set in 31-29\n", pa);
dd->ipath_egrtidbase = (u64 __iomem *)
((char __iomem *) dd->ipath_kregbase + dd->ipath_rcvegrbase);
- /*
- * To truly support a 4KB MTU (for usermode), we need to
- * bump this to a larger value. For now, we use them for
- * the kernel only.
- */
- dd->ipath_rcvegrbufsize = 2048;
+ dd->ipath_rcvegrbufsize = ipath_mtu4096 ? 4096 : 2048;
/*
* the min() check here is currently a nop, but it may not always
* be, depending on just how we do ipath_rcvegrbufsize
*/
- dd->ipath_ibmaxlen = min(dd->ipath_piosize2k,
+ dd->ipath_ibmaxlen = min(ipath_mtu4096 ? dd->ipath_piosize4k :
+ dd->ipath_piosize2k,
dd->ipath_rcvegrbufsize +
(dd->ipath_rcvhdrentsize << 2));
dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen;
projects / linux-2.6-omap-h63xx.git / blobdiff