/*
- * linux/drivers/ide/pci/siimage.c Version 1.17 Oct 18 2007
+ * linux/drivers/ide/pci/siimage.c Version 1.19 Nov 16 2007
*
* Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2003 Red Hat <alan@redhat.com>
*
* If you have strange problems with nVidia chipset systems please
* see the SI support documentation and update your system BIOS
- * if neccessary
+ * if necessary
*
* The Dell DRAC4 has some interesting features including effectively hot
* unplugging/replugging the virtual CD interface when the DRAC is reset.
static int pdev_is_sata(struct pci_dev *pdev)
{
- switch(pdev->device)
- {
+#ifdef CONFIG_BLK_DEV_IDE_SATA
+ switch(pdev->device) {
case PCI_DEVICE_ID_SII_3112:
case PCI_DEVICE_ID_SII_1210SA:
return 1;
return 0;
}
BUG();
+#endif
return 0;
}
-
+
/**
* is_sata - check if hwif is SATA
* @hwif: interface to check
* SI3112 SATA controller life is a bit simpler.
*/
-static u8 sil_udma_filter(ide_drive_t *drive)
+static u8 sil_pata_udma_filter(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
unsigned long base = (unsigned long) hwif->hwif_data;
else
pci_read_config_byte(hwif->pci_dev, 0x8A, &scsc);
- if (is_sata(hwif)) {
- mask = strstr(drive->id->model, "Maxtor") ? 0x3f : 0x7f;
- goto out;
- }
-
if ((scsc & 0x30) == 0x10) /* 133 */
- mask = 0x7f;
+ mask = ATA_UDMA6;
else if ((scsc & 0x30) == 0x20) /* 2xPCI */
- mask = 0x7f;
+ mask = ATA_UDMA6;
else if ((scsc & 0x30) == 0x00) /* 100 */
- mask = 0x3f;
+ mask = ATA_UDMA5;
else /* Disabled ? */
BUG();
-out:
+
return mask;
}
+static u8 sil_sata_udma_filter(ide_drive_t *drive)
+{
+ return strstr(drive->id->model, "Maxtor") ? ATA_UDMA5 : ATA_UDMA6;
+}
+
/**
* sil_set_pio_mode - set host controller for PIO mode
* @drive: drive
static int siimage_mmio_ide_dma_test_irq (ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
- unsigned long base = (unsigned long)hwif->hwif_data;
unsigned long addr = siimage_selreg(hwif, 0x1);
if (SATA_ERROR_REG) {
+ unsigned long base = (unsigned long)hwif->hwif_data;
+
u32 ext_stat = readl((void __iomem *)(base + 0x10));
u8 watchdog = 0;
if (ext_stat & ((hwif->channel) ? 0x40 : 0x10)) {
}
/**
- * siimage_busproc - bus isolation ioctl
+ * sil_sata_busproc - bus isolation IOCTL
* @drive: drive to isolate/restore
* @state: bus state to set
*
* SATA controller the work required is quite limited, we
* just have to clean up the statistics
*/
-
-static int siimage_busproc (ide_drive_t * drive, int state)
+
+static int sil_sata_busproc(ide_drive_t * drive, int state)
{
ide_hwif_t *hwif = HWIF(drive);
u32 stat_config = 0;
}
/**
- * siimage_reset_poll - wait for sata reset
+ * sil_sata_reset_poll - wait for SATA reset
* @drive: drive we are resetting
*
* Poll the SATA phy and see whether it has come back from the dead
* yet.
*/
-
-static int siimage_reset_poll (ide_drive_t *drive)
+
+static int sil_sata_reset_poll(ide_drive_t *drive)
{
if (SATA_STATUS_REG) {
ide_hwif_t *hwif = HWIF(drive);
HWGROUP(drive)->polling = 0;
return ide_started;
}
- return 0;
- } else {
- return 0;
}
+
+ return 0;
}
/**
- * siimage_pre_reset - reset hook
+ * sil_sata_pre_reset - reset hook
* @drive: IDE device being reset
*
* For the SATA devices we need to handle recalibration/geometry
* differently
*/
-
-static void siimage_pre_reset (ide_drive_t *drive)
-{
- if (drive->media != ide_disk)
- return;
- if (is_sata(HWIF(drive)))
- {
+static void sil_sata_pre_reset(ide_drive_t *drive)
+{
+ if (drive->media == ide_disk) {
drive->special.b.set_geometry = 0;
drive->special.b.recalibrate = 0;
}
}
-/**
- * siimage_reset - reset a device on an siimage controller
- * @drive: drive to reset
- *
- * Perform a controller level reset fo the device. For
- * SATA we must also check the PHY.
- */
-
-static void siimage_reset (ide_drive_t *drive)
-{
- ide_hwif_t *hwif = HWIF(drive);
- u8 reset = 0;
- unsigned long addr = siimage_selreg(hwif, 0);
-
- if (hwif->mmio) {
- reset = hwif->INB(addr);
- hwif->OUTB((reset|0x03), addr);
- /* FIXME:posting */
- udelay(25);
- hwif->OUTB(reset, addr);
- (void) hwif->INB(addr);
- } else {
- pci_read_config_byte(hwif->pci_dev, addr, &reset);
- pci_write_config_byte(hwif->pci_dev, addr, reset|0x03);
- udelay(25);
- pci_write_config_byte(hwif->pci_dev, addr, reset);
- pci_read_config_byte(hwif->pci_dev, addr, &reset);
- }
-
- if (SATA_STATUS_REG) {
- /* SATA_STATUS_REG is valid only when in MMIO mode */
- u32 sata_stat = readl((void __iomem *)SATA_STATUS_REG);
- printk(KERN_WARNING "%s: reset phy, status=0x%08x, %s\n",
- hwif->name, sata_stat, __FUNCTION__);
- if (!(sata_stat)) {
- printk(KERN_WARNING "%s: reset phy dead, status=0x%08x\n",
- hwif->name, sata_stat);
- drive->failures++;
- }
- }
-
-}
-
/**
* proc_reports_siimage - add siimage controller to proc
* @dev: PCI device
static unsigned int __devinit init_chipset_siimage(struct pci_dev *dev, const char *name)
{
- u32 class_rev = 0;
- u8 tmpbyte = 0;
- u8 BA5_EN = 0;
+ u8 rev = dev->revision, tmpbyte = 0, BA5_EN = 0;
- pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
- class_rev &= 0xff;
- pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (class_rev) ? 1 : 255);
+ pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, rev ? 1 : 255);
pci_read_config_byte(dev, 0x8A, &BA5_EN);
if ((BA5_EN & 0x01) || (pci_resource_start(dev, 5))) {
hwif->sata_misc[SATA_IEN_OFFSET] = base + 0x148;
}
- hw.irq = hwif->pci_dev->irq;
-
- memcpy(&hwif->hw, &hw, sizeof(hw));
- memcpy(hwif->io_ports, hwif->hw.io_ports, sizeof(hwif->hw.io_ports));
+ memcpy(hwif->io_ports, hw.io_ports, sizeof(hwif->io_ports));
- hwif->irq = hw.irq;
+ hwif->irq = dev->irq;
- base = (unsigned long) addr;
-
- hwif->dma_base = base + (ch ? 0x08 : 0x00);
+ hwif->dma_base = (unsigned long)addr + (ch ? 0x08 : 0x00);
hwif->mmio = 1;
}
static void __devinit init_iops_siimage(ide_hwif_t *hwif)
{
- struct pci_dev *dev = hwif->pci_dev;
- u32 class_rev = 0;
-
- pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
- class_rev &= 0xff;
-
hwif->hwif_data = NULL;
/* Pessimal until we finish probing */
hwif->rqsize = 15;
- if (pci_get_drvdata(dev) == NULL)
+ if (pci_get_drvdata(hwif->pci_dev) == NULL)
return;
+
init_mmio_iops_siimage(hwif);
}
static void __devinit init_hwif_siimage(ide_hwif_t *hwif)
{
- hwif->resetproc = &siimage_reset;
+ u8 sata = is_sata(hwif);
+
hwif->set_pio_mode = &sil_set_pio_mode;
hwif->set_dma_mode = &sil_set_dma_mode;
- hwif->reset_poll = &siimage_reset_poll;
- hwif->pre_reset = &siimage_pre_reset;
- hwif->udma_filter = &sil_udma_filter;
- if(is_sata(hwif)) {
+ if (sata) {
static int first = 1;
- hwif->busproc = &siimage_busproc;
+ hwif->busproc = &sil_sata_busproc;
+ hwif->reset_poll = &sil_sata_reset_poll;
+ hwif->pre_reset = &sil_sata_pre_reset;
+ hwif->udma_filter = &sil_sata_udma_filter;
if (first) {
printk(KERN_INFO "siimage: For full SATA support you should use the libata sata_sil module.\n");
first = 0;
}
- }
-
- hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
+ } else
+ hwif->udma_filter = &sil_pata_udma_filter;
if (hwif->dma_base == 0)
return;
- hwif->ultra_mask = 0x7f;
- hwif->mwdma_mask = 0x07;
-
- if (is_sata(hwif))
+ if (sata)
hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
.fixup = siimage_fixup, \
.host_flags = IDE_HFLAG_BOOTABLE, \
.pio_mask = ATA_PIO4, \
+ .mwdma_mask = ATA_MWDMA2, \
+ .udma_mask = ATA_UDMA6, \
}
-static ide_pci_device_t siimage_chipsets[] __devinitdata = {
+static const struct ide_port_info siimage_chipsets[] __devinitdata = {
/* 0 */ DECLARE_SII_DEV("SiI680"),
/* 1 */ DECLARE_SII_DEV("SiI3112 Serial ATA"),
/* 2 */ DECLARE_SII_DEV("Adaptec AAR-1210SA")
projects / linux-2.6-omap-h63xx.git / blobdiff