siimage: remove resetproc() method

[linux-2.6-omap-h63xx.git] / drivers / ide / pci / siimage.c

diff --git a/drivers/ide/pci/siimage.c b/drivers/ide/pci/siimage.c
index 6d99441c605be1836843c514de2a780b8dcee804..5709c252543b5c7a68a4b04064f26e85ef8ac2dc 100644 (file)
--- a/drivers/ide/pci/siimage.c
+++ b/drivers/ide/pci/siimage.c
@@ -1,5 +1,5 @@
 /*
- * linux/drivers/ide/pci/siimage.c             Version 1.18    Oct 18 2007
+ * linux/drivers/ide/pci/siimage.c             Version 1.19    Nov 16 2007
  *
  * Copyright (C) 2001-2002     Andre Hedrick <andre@linux-ide.org>
  * Copyright (C) 2003          Red Hat <alan@redhat.com>
@@ -459,48 +459,6 @@ static void sil_sata_pre_reset(ide_drive_t *drive)
        }
 }
 
-/**
- *     siimage_reset   -       reset a device on an siimage controller
- *     @drive: drive to reset
- *
- *     Perform a controller level reset fo the device. For
- *     SATA we must also check the PHY.
- */
- 
-static void siimage_reset (ide_drive_t *drive)
-{
-       ide_hwif_t *hwif        = HWIF(drive);
-       u8 reset                = 0;
-       unsigned long addr      = siimage_selreg(hwif, 0);
-
-       if (hwif->mmio) {
-               reset = hwif->INB(addr);
-               hwif->OUTB((reset|0x03), addr);
-               /* FIXME:posting */
-               udelay(25);
-               hwif->OUTB(reset, addr);
-               (void) hwif->INB(addr);
-       } else {
-               pci_read_config_byte(hwif->pci_dev, addr, &reset);
-               pci_write_config_byte(hwif->pci_dev, addr, reset|0x03);
-               udelay(25);
-               pci_write_config_byte(hwif->pci_dev, addr, reset);
-               pci_read_config_byte(hwif->pci_dev, addr, &reset);
-       }
-
-       if (SATA_STATUS_REG) {
-               /* SATA_STATUS_REG is valid only when in MMIO mode */
-               u32 sata_stat = readl((void __iomem *)SATA_STATUS_REG);
-               printk(KERN_WARNING "%s: reset phy, status=0x%08x, %s\n",
-                       hwif->name, sata_stat, __FUNCTION__);
-               if (!(sata_stat)) {
-                       printk(KERN_WARNING "%s: reset phy dead, status=0x%08x\n",
-                               hwif->name, sata_stat);
-                       drive->failures++;
-               }
-       }
-}
-
 /**
  *     proc_reports_siimage            -       add siimage controller to proc
  *     @dev: PCI device
@@ -857,7 +815,6 @@ static void __devinit init_hwif_siimage(ide_hwif_t *hwif)
 {
        u8 sata = is_sata(hwif);
 
-       hwif->resetproc = &siimage_reset;
        hwif->set_pio_mode = &sil_set_pio_mode;
        hwif->set_dma_mode = &sil_set_dma_mode;