/*
- * linux/drivers/ide/pci/hpt366.c Version 1.03 May 4, 2007
+ * linux/drivers/ide/pci/hpt366.c Version 1.06 Jun 27, 2007
*
* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* switch to calculating PCI clock frequency based on the chip's base DPLL
* frequency
* - switch to using the DPLL clock and enable UltraATA/133 mode by default on
- * anything newer than HPT370/A
+ * anything newer than HPT370/A (except HPT374 that is not capable of this
+ * mode according to the manual)
* - fold PCI clock detection and DPLL setup code into init_chipset_hpt366(),
* also fixing the interchanged 25/40 MHz PCI clock cases for HPT36x chips;
* unify HPT36x/37x timing setup code and the speedproc handlers by joining
"IC35L040AVER07-0",
"IC35L060AVER07-0",
"WDC AC310200R",
+ "MAXTOR STM3320620A",
NULL
};
};
#define HPT366_DEBUG_DRIVE_INFO 0
-#define HPT374_ALLOW_ATA133_6 1
#define HPT371_ALLOW_ATA133_6 1
#define HPT302_ALLOW_ATA133_6 1
#define HPT372_ALLOW_ATA133_6 1
static struct hpt_info hpt374 __devinitdata = {
.chip_type = HPT374,
- .max_mode = HPT374_ALLOW_ATA133_6 ? 4 : 3,
+ .max_mode = 3,
.dpll_clk = 48,
.settings = hpt37x_settings
};
return 0;
}
-static u8 hpt3xx_ratemask(ide_drive_t *drive)
-{
- struct hpt_info *info = pci_get_drvdata(HWIF(drive)->pci_dev);
- u8 mode = info->max_mode;
-
- if (!eighty_ninty_three(drive) && mode)
- mode = min(mode, (u8)1);
- return mode;
-}
-
/*
* Note for the future; the SATA hpt37x we must set
* either PIO or UDMA modes 0,4,5
*/
-
-static u8 hpt3xx_ratefilter(ide_drive_t *drive, u8 speed)
+
+static u8 hpt3xx_udma_filter(ide_drive_t *drive)
{
struct hpt_info *info = pci_get_drvdata(HWIF(drive)->pci_dev);
u8 chip_type = info->chip_type;
- u8 mode = hpt3xx_ratemask(drive);
-
- if (drive->media != ide_disk)
- return min(speed, (u8)XFER_PIO_4);
+ u8 mode = info->max_mode;
+ u8 mask;
switch (mode) {
case 0x04:
- speed = min_t(u8, speed, XFER_UDMA_6);
+ mask = 0x7f;
break;
case 0x03:
- speed = min_t(u8, speed, XFER_UDMA_5);
+ mask = 0x3f;
if (chip_type >= HPT374)
break;
if (!check_in_drive_list(drive, bad_ata100_5))
goto check_bad_ata33;
/* fall thru */
case 0x02:
- speed = min_t(u8, speed, XFER_UDMA_4);
+ mask = 0x1f;
/*
* CHECK ME, Does this need to be changed to HPT374 ??
!check_in_drive_list(drive, bad_ata66_4))
goto check_bad_ata33;
- speed = min_t(u8, speed, XFER_UDMA_3);
+ mask = 0x0f;
if (HPT366_ALLOW_ATA66_3 &&
!check_in_drive_list(drive, bad_ata66_3))
goto check_bad_ata33;
/* fall thru */
case 0x01:
- speed = min_t(u8, speed, XFER_UDMA_2);
+ mask = 0x07;
check_bad_ata33:
if (chip_type >= HPT370A)
/* fall thru */
case 0x00:
default:
- speed = min_t(u8, speed, XFER_MW_DMA_2);
+ mask = 0x00;
break;
}
- return speed;
+ return mask;
}
static u32 get_speed_setting(u8 speed, struct hpt_info *info)
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
struct hpt_info *info = pci_get_drvdata(dev);
- u8 speed = hpt3xx_ratefilter(drive, xferspeed);
+ u8 speed = ide_rate_filter(drive, xferspeed);
u8 itr_addr = drive->dn ? 0x44 : 0x40;
- u32 itr_mask = speed < XFER_MW_DMA_0 ? 0x30070000 :
- (speed < XFER_UDMA_0 ? 0xc0070000 : 0xc03800ff);
- u32 new_itr = get_speed_setting(speed, info);
u32 old_itr = 0;
+ u32 itr_mask, new_itr;
+
+ /* TODO: move this to ide_rate_filter() [ check ->atapi_dma ] */
+ if (drive->media != ide_disk)
+ speed = min_t(u8, speed, XFER_PIO_4);
+
+ itr_mask = speed < XFER_MW_DMA_0 ? 0x30070000 :
+ (speed < XFER_UDMA_0 ? 0xc0070000 : 0xc03800ff);
+
+ new_itr = get_speed_setting(speed, info);
/*
* Disable on-chip PIO FIFO/buffer (and PIO MST mode as well)
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
struct hpt_info *info = pci_get_drvdata(dev);
- u8 speed = hpt3xx_ratefilter(drive, xferspeed);
+ u8 speed = ide_rate_filter(drive, xferspeed);
u8 itr_addr = 0x40 + (drive->dn * 4);
- u32 itr_mask = speed < XFER_MW_DMA_0 ? 0x303c0000 :
- (speed < XFER_UDMA_0 ? 0xc03c0000 : 0xc1c001ff);
- u32 new_itr = get_speed_setting(speed, info);
u32 old_itr = 0;
+ u32 itr_mask, new_itr;
+
+ /* TODO: move this to ide_rate_filter() [ check ->atapi_dma ] */
+ if (drive->media != ide_disk)
+ speed = min_t(u8, speed, XFER_PIO_4);
+
+ itr_mask = speed < XFER_MW_DMA_0 ? 0x303c0000 :
+ (speed < XFER_UDMA_0 ? 0xc03c0000 : 0xc1c001ff);
+
+ new_itr = get_speed_setting(speed, info);
pci_read_config_dword(dev, itr_addr, &old_itr);
new_itr = (new_itr & ~itr_mask) | (old_itr & itr_mask);
(void) hpt3xx_tune_chipset (drive, XFER_PIO_0 + pio);
}
-/*
- * This allows the configuration of ide_pci chipset registers
- * for cards that learn about the drive's UDMA, DMA, PIO capabilities
- * after the drive is reported by the OS. Initially designed for
- * HPT366 UDMA chipset by HighPoint|Triones Technologies, Inc.
- *
- */
-static int config_chipset_for_dma(ide_drive_t *drive)
-{
- u8 speed = ide_dma_speed(drive, hpt3xx_ratemask(drive));
-
- if (!speed)
- return 0;
-
- (void) hpt3xx_tune_chipset(drive, speed);
- return ide_dma_enable(drive);
-}
-
static int hpt3xx_quirkproc(ide_drive_t *drive)
{
struct hd_driveid *id = drive->id;
{
drive->init_speed = 0;
- if (ide_use_dma(drive) && config_chipset_for_dma(drive))
+ if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
hwif->intrproc = &hpt3xx_intrproc;
hwif->maskproc = &hpt3xx_maskproc;
hwif->busproc = &hpt3xx_busproc;
+ hwif->udma_filter = &hpt3xx_udma_filter;
/*
* HPT3xxN chips have some complications:
goto init_single;
/*
- * HPT36x chips are single channel and
- * do not seem to have the channel enable bit...
+ * HPT36x chips have one channel per function and have
+ * both channel enable bits located differently and visible
+ * to both functions -- really stupid design decision... :-(
+ * Bit 4 is for the primary channel, bit 5 for the secondary.
*/
d->channels = 1;
- d->enablebits[0].reg = 0;
+ d->enablebits[0].mask = d->enablebits[0].val = 0x10;
if ((dev2 = pci_get_slot(dev->bus, dev->devfn + 1)) != NULL) {
- u8 pin1 = 0, pin2 = 0;
+ u8 mcr1 = 0, pin1 = 0, pin2 = 0;
int ret;
pci_set_drvdata(dev2, info[rev]);
+ /*
+ * Now we'll have to force both channels enabled if
+ * at least one of them has been enabled by BIOS...
+ */
+ pci_read_config_byte(dev, 0x50, &mcr1);
+ if (mcr1 & 0x30)
+ pci_write_config_byte(dev, 0x50, mcr1 | 0x30);
+
pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin1);
pci_read_config_byte(dev2, PCI_INTERRUPT_PIN, &pin2);
if (pin1 != pin2 && dev->irq == dev2->irq) {