static int idebus_parameter; /* holds the "idebus=" parameter */
static int system_bus_speed; /* holds what we think is VESA/PCI bus speed */
-static int initializing; /* set while initializing built-in drivers */
DECLARE_MUTEX(ide_cfg_sem);
__cacheline_aligned_in_smp DEFINE_SPINLOCK(ide_lock);
-#ifdef CONFIG_BLK_DEV_IDEPCI
+#ifdef CONFIG_IDEPCI_PCIBUS_ORDER
static int ide_scan_direction; /* THIS was formerly 2.2.x pci=reverse */
#endif
#endif
}
#ifdef CONFIG_IDE_ARM
- initializing = 1;
ide_arm_init();
- initializing = 0;
#endif
}
return system_bus_speed;
}
-#ifdef CONFIG_PROC_FS
-struct proc_dir_entry *proc_ide_root;
-#endif
-
static struct resource* hwif_request_region(ide_hwif_t *hwif,
unsigned long addr, int num)
{
hwif->tuneproc = tmp_hwif->tuneproc;
hwif->speedproc = tmp_hwif->speedproc;
+ hwif->udma_filter = tmp_hwif->udma_filter;
hwif->selectproc = tmp_hwif->selectproc;
hwif->reset_poll = tmp_hwif->reset_poll;
hwif->pre_reset = tmp_hwif->pre_reset;
hwif->ide_dma_clear_irq = tmp_hwif->ide_dma_clear_irq;
hwif->dma_host_on = tmp_hwif->dma_host_on;
hwif->dma_host_off = tmp_hwif->dma_host_off;
- hwif->ide_dma_lostirq = tmp_hwif->ide_dma_lostirq;
- hwif->ide_dma_timeout = tmp_hwif->ide_dma_timeout;
+ hwif->dma_lost_irq = tmp_hwif->dma_lost_irq;
+ hwif->dma_timeout = tmp_hwif->dma_timeout;
hwif->OUTB = tmp_hwif->OUTB;
hwif->OUTBSYNC = tmp_hwif->OUTBSYNC;
spin_unlock_irq(&ide_lock);
- destroy_proc_ide_interface(hwif);
+ ide_proc_unregister_port(hwif);
hwgroup = hwif->hwgroup;
/*
/**
* ide_register_hw_with_fixup - register IDE interface
* @hw: hardware registers
+ * @initializing: set while initializing built-in drivers
* @hwifp: pointer to returned hwif
* @fixup: fixup function
*
* Returns -1 on error.
*/
-int ide_register_hw_with_fixup(hw_regs_t *hw, ide_hwif_t **hwifp, void(*fixup)(ide_hwif_t *hwif))
+int ide_register_hw_with_fixup(hw_regs_t *hw, int initializing,
+ ide_hwif_t **hwifp,
+ void(*fixup)(ide_hwif_t *hwif))
{
int index, retry = 1;
ide_hwif_t *hwif;
if (!initializing) {
probe_hwif_init_with_fixup(hwif, fixup);
- create_proc_ide_interfaces();
+ ide_proc_register_port(hwif);
}
if (hwifp)
EXPORT_SYMBOL(ide_register_hw_with_fixup);
-int ide_register_hw(hw_regs_t *hw, ide_hwif_t **hwifp)
+int ide_register_hw(hw_regs_t *hw, int initializing, ide_hwif_t **hwifp)
{
- return ide_register_hw_with_fixup(hw, hwifp, NULL);
+ return ide_register_hw_with_fixup(hw, initializing, hwifp, NULL);
}
EXPORT_SYMBOL(ide_register_hw);
DECLARE_MUTEX(ide_setting_sem);
-/**
- * __ide_add_setting - add an ide setting option
- * @drive: drive to use
- * @name: setting name
- * @rw: true if the function is read write
- * @read_ioctl: function to call on read
- * @write_ioctl: function to call on write
- * @data_type: type of data
- * @min: range minimum
- * @max: range maximum
- * @mul_factor: multiplication scale
- * @div_factor: divison scale
- * @data: private data field
- * @set: setting
- * @auto_remove: setting auto removal flag
- *
- * Removes the setting named from the device if it is present.
- * The function takes the settings_lock to protect against
- * parallel changes. This function must not be called from IRQ
- * context. Returns 0 on success or -1 on failure.
- *
- * BUGS: This code is seriously over-engineered. There is also
- * magic about how the driver specific features are setup. If
- * a driver is attached we assume the driver settings are auto
- * remove.
- */
-
-static int __ide_add_setting(ide_drive_t *drive, const char *name, int rw, int read_ioctl, int write_ioctl, int data_type, int min, int max, int mul_factor, int div_factor, void *data, ide_procset_t *set, int auto_remove)
-{
- ide_settings_t **p = (ide_settings_t **) &drive->settings, *setting = NULL;
-
- down(&ide_setting_sem);
- while ((*p) && strcmp((*p)->name, name) < 0)
- p = &((*p)->next);
- if ((setting = kzalloc(sizeof(*setting), GFP_KERNEL)) == NULL)
- goto abort;
- if ((setting->name = kmalloc(strlen(name) + 1, GFP_KERNEL)) == NULL)
- goto abort;
- strcpy(setting->name, name);
- setting->rw = rw;
- setting->read_ioctl = read_ioctl;
- setting->write_ioctl = write_ioctl;
- setting->data_type = data_type;
- setting->min = min;
- setting->max = max;
- setting->mul_factor = mul_factor;
- setting->div_factor = div_factor;
- setting->data = data;
- setting->set = set;
-
- setting->next = *p;
- if (auto_remove)
- setting->auto_remove = 1;
- *p = setting;
- up(&ide_setting_sem);
- return 0;
-abort:
- up(&ide_setting_sem);
- kfree(setting);
- return -1;
-}
-
-int ide_add_setting(ide_drive_t *drive, const char *name, int rw, int read_ioctl, int write_ioctl, int data_type, int min, int max, int mul_factor, int div_factor, void *data, ide_procset_t *set)
-{
- return __ide_add_setting(drive, name, rw, read_ioctl, write_ioctl, data_type, min, max, mul_factor, div_factor, data, set, 1);
-}
-
-EXPORT_SYMBOL(ide_add_setting);
-
-/**
- * __ide_remove_setting - remove an ide setting option
- * @drive: drive to use
- * @name: setting name
- *
- * Removes the setting named from the device if it is present.
- * The caller must hold the setting semaphore.
- */
-
-static void __ide_remove_setting (ide_drive_t *drive, char *name)
-{
- ide_settings_t **p, *setting;
-
- p = (ide_settings_t **) &drive->settings;
-
- while ((*p) && strcmp((*p)->name, name))
- p = &((*p)->next);
- if ((setting = (*p)) == NULL)
- return;
-
- (*p) = setting->next;
-
- kfree(setting->name);
- kfree(setting);
-}
-
-/**
- * ide_find_setting_by_ioctl - find a drive specific ioctl
- * @drive: drive to scan
- * @cmd: ioctl command to handle
- *
- * Scan's the device setting table for a matching entry and returns
- * this or NULL if no entry is found. The caller must hold the
- * setting semaphore
- */
-
-static ide_settings_t *ide_find_setting_by_ioctl (ide_drive_t *drive, int cmd)
-{
- ide_settings_t *setting = drive->settings;
-
- while (setting) {
- if (setting->read_ioctl == cmd || setting->write_ioctl == cmd)
- break;
- setting = setting->next;
- }
-
- return setting;
-}
-
-/**
- * ide_find_setting_by_name - find a drive specific setting
- * @drive: drive to scan
- * @name: setting name
- *
- * Scan's the device setting table for a matching entry and returns
- * this or NULL if no entry is found. The caller must hold the
- * setting semaphore
- */
-
-ide_settings_t *ide_find_setting_by_name (ide_drive_t *drive, char *name)
-{
- ide_settings_t *setting = drive->settings;
-
- while (setting) {
- if (strcmp(setting->name, name) == 0)
- break;
- setting = setting->next;
- }
- return setting;
-}
-
-/**
- * auto_remove_settings - remove driver specific settings
- * @drive: drive
- *
- * Automatically remove all the driver specific settings for this
- * drive. This function may not be called from IRQ context. The
- * caller must hold ide_setting_sem.
- */
-
-static void auto_remove_settings (ide_drive_t *drive)
-{
- ide_settings_t *setting;
-repeat:
- setting = drive->settings;
- while (setting) {
- if (setting->auto_remove) {
- __ide_remove_setting(drive, setting->name);
- goto repeat;
- }
- setting = setting->next;
- }
-}
-
-/**
- * ide_read_setting - read an IDE setting
- * @drive: drive to read from
- * @setting: drive setting
- *
- * Read a drive setting and return the value. The caller
- * must hold the ide_setting_sem when making this call.
- *
- * BUGS: the data return and error are the same return value
- * so an error -EINVAL and true return of the same value cannot
- * be told apart
- */
-
-int ide_read_setting (ide_drive_t *drive, ide_settings_t *setting)
-{
- int val = -EINVAL;
- unsigned long flags;
-
- if ((setting->rw & SETTING_READ)) {
- spin_lock_irqsave(&ide_lock, flags);
- switch(setting->data_type) {
- case TYPE_BYTE:
- val = *((u8 *) setting->data);
- break;
- case TYPE_SHORT:
- val = *((u16 *) setting->data);
- break;
- case TYPE_INT:
- case TYPE_INTA:
- val = *((u32 *) setting->data);
- break;
- }
- spin_unlock_irqrestore(&ide_lock, flags);
- }
- return val;
-}
+EXPORT_SYMBOL_GPL(ide_setting_sem);
/**
* ide_spin_wait_hwgroup - wait for group
EXPORT_SYMBOL(ide_spin_wait_hwgroup);
-/**
- * ide_write_setting - read an IDE setting
- * @drive: drive to read from
- * @setting: drive setting
- * @val: value
- *
- * Write a drive setting if it is possible. The caller
- * must hold the ide_setting_sem when making this call.
- *
- * BUGS: the data return and error are the same return value
- * so an error -EINVAL and true return of the same value cannot
- * be told apart
- *
- * FIXME: This should be changed to enqueue a special request
- * to the driver to change settings, and then wait on a sema for completion.
- * The current scheme of polling is kludgy, though safe enough.
- */
-
-int ide_write_setting (ide_drive_t *drive, ide_settings_t *setting, int val)
+int set_io_32bit(ide_drive_t *drive, int arg)
{
- int i;
- u32 *p;
-
- if (!capable(CAP_SYS_ADMIN))
- return -EACCES;
- if (!(setting->rw & SETTING_WRITE))
+ if (drive->no_io_32bit)
return -EPERM;
- if (val < setting->min || val > setting->max)
+
+ if (arg < 0 || arg > 1 + (SUPPORT_VLB_SYNC << 1))
return -EINVAL;
- if (setting->set)
- return setting->set(drive, val);
- if (ide_spin_wait_hwgroup(drive))
- return -EBUSY;
- switch (setting->data_type) {
- case TYPE_BYTE:
- *((u8 *) setting->data) = val;
- break;
- case TYPE_SHORT:
- *((u16 *) setting->data) = val;
- break;
- case TYPE_INT:
- *((u32 *) setting->data) = val;
- break;
- case TYPE_INTA:
- p = (u32 *) setting->data;
- for (i = 0; i < 1 << PARTN_BITS; i++, p++)
- *p = val;
- break;
- }
- spin_unlock_irq(&ide_lock);
- return 0;
-}
-static int set_io_32bit(ide_drive_t *drive, int arg)
-{
drive->io_32bit = arg;
#ifdef CONFIG_BLK_DEV_DTC2278
if (HWIF(drive)->chipset == ide_dtc2278)
return 0;
}
-static int set_using_dma (ide_drive_t *drive, int arg)
+static int set_ksettings(ide_drive_t *drive, int arg)
+{
+ if (arg < 0 || arg > 1)
+ return -EINVAL;
+
+ if (ide_spin_wait_hwgroup(drive))
+ return -EBUSY;
+ drive->keep_settings = arg;
+ spin_unlock_irq(&ide_lock);
+
+ return 0;
+}
+
+int set_using_dma(ide_drive_t *drive, int arg)
{
#ifdef CONFIG_BLK_DEV_IDEDMA
ide_hwif_t *hwif = drive->hwif;
int err = -EPERM;
+ if (arg < 0 || arg > 1)
+ return -EINVAL;
+
if (!drive->id || !(drive->id->capability & 1))
goto out;
err = 0;
if (arg) {
+ hwif->dma_off_quietly(drive);
if (ide_set_dma(drive) || hwif->ide_dma_on(drive))
err = -EIO;
} else
out:
return err;
#else
+ if (arg < 0 || arg > 1)
+ return -EINVAL;
+
return -EPERM;
#endif
}
-static int set_pio_mode (ide_drive_t *drive, int arg)
+int set_pio_mode(ide_drive_t *drive, int arg)
{
struct request rq;
+ if (arg < 0 || arg > 255)
+ return -EINVAL;
+
if (!HWIF(drive)->tuneproc)
return -ENOSYS;
if (drive->special.b.set_tune)
return 0;
}
-static int set_xfer_rate (ide_drive_t *drive, int arg)
+static int set_unmaskirq(ide_drive_t *drive, int arg)
{
- int err = ide_wait_cmd(drive,
- WIN_SETFEATURES, (u8) arg,
- SETFEATURES_XFER, 0, NULL);
+ if (drive->no_unmask)
+ return -EPERM;
- if (!err && arg) {
- ide_set_xfer_rate(drive, (u8) arg);
- ide_driveid_update(drive);
- }
- return err;
-}
+ if (arg < 0 || arg > 1)
+ return -EINVAL;
-/**
- * ide_add_generic_settings - generic ide settings
- * @drive: drive being configured
- *
- * Add the generic parts of the system settings to the /proc files and
- * ioctls for this IDE device. The caller must not be holding the
- * ide_setting_sem.
- */
+ if (ide_spin_wait_hwgroup(drive))
+ return -EBUSY;
+ drive->unmask = arg;
+ spin_unlock_irq(&ide_lock);
-void ide_add_generic_settings (ide_drive_t *drive)
-{
-/*
- * drive setting name read/write access read ioctl write ioctl data type min max mul_factor div_factor data pointer set function
- */
- __ide_add_setting(drive, "io_32bit", drive->no_io_32bit ? SETTING_READ : SETTING_RW, HDIO_GET_32BIT, HDIO_SET_32BIT, TYPE_BYTE, 0, 1 + (SUPPORT_VLB_SYNC << 1), 1, 1, &drive->io_32bit, set_io_32bit, 0);
- __ide_add_setting(drive, "keepsettings", SETTING_RW, HDIO_GET_KEEPSETTINGS, HDIO_SET_KEEPSETTINGS, TYPE_BYTE, 0, 1, 1, 1, &drive->keep_settings, NULL, 0);
- __ide_add_setting(drive, "nice1", SETTING_RW, -1, -1, TYPE_BYTE, 0, 1, 1, 1, &drive->nice1, NULL, 0);
- __ide_add_setting(drive, "pio_mode", SETTING_WRITE, -1, HDIO_SET_PIO_MODE, TYPE_BYTE, 0, 255, 1, 1, NULL, set_pio_mode, 0);
- __ide_add_setting(drive, "unmaskirq", drive->no_unmask ? SETTING_READ : SETTING_RW, HDIO_GET_UNMASKINTR, HDIO_SET_UNMASKINTR, TYPE_BYTE, 0, 1, 1, 1, &drive->unmask, NULL, 0);
- __ide_add_setting(drive, "using_dma", SETTING_RW, HDIO_GET_DMA, HDIO_SET_DMA, TYPE_BYTE, 0, 1, 1, 1, &drive->using_dma, set_using_dma, 0);
- __ide_add_setting(drive, "init_speed", SETTING_RW, -1, -1, TYPE_BYTE, 0, 70, 1, 1, &drive->init_speed, NULL, 0);
- __ide_add_setting(drive, "current_speed", SETTING_RW, -1, -1, TYPE_BYTE, 0, 70, 1, 1, &drive->current_speed, set_xfer_rate, 0);
- __ide_add_setting(drive, "number", SETTING_RW, -1, -1, TYPE_BYTE, 0, 3, 1, 1, &drive->dn, NULL, 0);
+ return 0;
}
/**
struct request rq;
struct request_pm_state rqpm;
ide_task_t args;
+ int err;
/* Call ACPI _STM only once */
if (!(drive->dn % 2))
rqpm.pm_step = ide_pm_state_start_resume;
rqpm.pm_state = PM_EVENT_ON;
- return ide_do_drive_cmd(drive, &rq, ide_head_wait);
+ err = ide_do_drive_cmd(drive, &rq, ide_head_wait);
+
+ if (err == 0 && dev->driver) {
+ ide_driver_t *drv = to_ide_driver(dev->driver);
+
+ if (drv->resume)
+ drv->resume(drive);
+ }
+
+ return err;
}
int generic_ide_ioctl(ide_drive_t *drive, struct file *file, struct block_device *bdev,
unsigned int cmd, unsigned long arg)
{
- ide_settings_t *setting;
+ unsigned long flags;
ide_driver_t *drv;
- int err = 0;
void __user *p = (void __user *)arg;
+ int err = 0, (*setfunc)(ide_drive_t *, int);
+ u8 *val;
- down(&ide_setting_sem);
- if ((setting = ide_find_setting_by_ioctl(drive, cmd)) != NULL) {
- if (cmd == setting->read_ioctl) {
- err = ide_read_setting(drive, setting);
- up(&ide_setting_sem);
- return err >= 0 ? put_user(err, (long __user *)arg) : err;
- } else {
- if (bdev != bdev->bd_contains)
- err = -EINVAL;
- else
- err = ide_write_setting(drive, setting, arg);
- up(&ide_setting_sem);
- return err;
- }
+ switch (cmd) {
+ case HDIO_GET_32BIT: val = &drive->io_32bit; goto read_val;
+ case HDIO_GET_KEEPSETTINGS: val = &drive->keep_settings; goto read_val;
+ case HDIO_GET_UNMASKINTR: val = &drive->unmask; goto read_val;
+ case HDIO_GET_DMA: val = &drive->using_dma; goto read_val;
+ case HDIO_SET_32BIT: setfunc = set_io_32bit; goto set_val;
+ case HDIO_SET_KEEPSETTINGS: setfunc = set_ksettings; goto set_val;
+ case HDIO_SET_PIO_MODE: setfunc = set_pio_mode; goto set_val;
+ case HDIO_SET_UNMASKINTR: setfunc = set_unmaskirq; goto set_val;
+ case HDIO_SET_DMA: setfunc = set_using_dma; goto set_val;
}
- up(&ide_setting_sem);
switch (cmd) {
case HDIO_OBSOLETE_IDENTITY:
ide_init_hwif_ports(&hw, (unsigned long) args[0],
(unsigned long) args[1], NULL);
hw.irq = args[2];
- if (ide_register_hw(&hw, NULL) == -1)
+ if (ide_register_hw(&hw, 0, NULL) == -1)
return -EIO;
return 0;
}
default:
return -EINVAL;
}
+
+read_val:
+ down(&ide_setting_sem);
+ spin_lock_irqsave(&ide_lock, flags);
+ err = *val;
+ spin_unlock_irqrestore(&ide_lock, flags);
+ up(&ide_setting_sem);
+ return err >= 0 ? put_user(err, (long __user *)arg) : err;
+
+set_val:
+ if (bdev != bdev->bd_contains)
+ err = -EINVAL;
+ else {
+ if (!capable(CAP_SYS_ADMIN))
+ err = -EACCES;
+ else {
+ down(&ide_setting_sem);
+ err = setfunc(drive, arg);
+ up(&ide_setting_sem);
+ }
+ }
+ return err;
}
EXPORT_SYMBOL(generic_ide_ioctl);
return 1;
}
-#ifdef CONFIG_BLK_DEV_IDEPCI
+#ifdef CONFIG_IDEPCI_PCIBUS_ORDER
if (!strcmp(s, "ide=reverse")) {
ide_scan_direction = 1;
printk(" : Enabled support for IDE inverse scan order.\n");
return 1;
}
-#endif /* CONFIG_BLK_DEV_IDEPCI */
+#endif
#ifdef CONFIG_BLK_DEV_IDEACPI
if (!strcmp(s, "ide=noacpi")) {
*/
static void __init probe_for_hwifs (void)
{
-#ifdef CONFIG_BLK_DEV_IDEPCI
+#ifdef CONFIG_IDEPCI_PCIBUS_ORDER
ide_scan_pcibus(ide_scan_direction);
-#endif /* CONFIG_BLK_DEV_IDEPCI */
+#endif
#ifdef CONFIG_ETRAX_IDE
{
#endif
}
-void ide_register_subdriver(ide_drive_t *drive, ide_driver_t *driver)
-{
-#ifdef CONFIG_PROC_FS
- ide_add_proc_entries(drive->proc, driver->proc, drive);
-#endif
-}
-
-EXPORT_SYMBOL(ide_register_subdriver);
-
-/**
- * ide_unregister_subdriver - disconnect drive from driver
- * @drive: drive to unplug
- * @driver: driver
- *
- * Disconnect a drive from the driver it was attached to and then
- * clean up the various proc files and other objects attached to it.
- *
- * Takes ide_setting_sem and ide_lock.
- * Caller must hold none of the locks.
- */
-
-void ide_unregister_subdriver(ide_drive_t *drive, ide_driver_t *driver)
-{
- unsigned long flags;
-
-#ifdef CONFIG_PROC_FS
- ide_remove_proc_entries(drive->proc, driver->proc);
-#endif
- down(&ide_setting_sem);
- spin_lock_irqsave(&ide_lock, flags);
- /*
- * ide_setting_sem protects the settings list
- * ide_lock protects the use of settings
- *
- * so we need to hold both, ide_settings_sem because we want to
- * modify the settings list, and ide_lock because we cannot take
- * a setting out that is being used.
- *
- * OTOH both ide_{read,write}_setting are only ever used under
- * ide_setting_sem.
- */
- auto_remove_settings(drive);
- spin_unlock_irqrestore(&ide_lock, flags);
- up(&ide_setting_sem);
-}
-
-EXPORT_SYMBOL(ide_unregister_subdriver);
-
/*
* Probe module
*/
init_ide_data();
-#ifdef CONFIG_PROC_FS
- proc_ide_root = proc_mkdir("ide", NULL);
-#endif
+ proc_ide_create();
#ifdef CONFIG_BLK_DEV_ALI14XX
if (probe_ali14xx)
(void)qd65xx_init();
#endif
- initializing = 1;
/* Probe for special PCI and other "known" interface chipsets. */
probe_for_hwifs();
- initializing = 0;
-#ifdef CONFIG_PROC_FS
- proc_ide_create();
-#endif
return 0;
}
pnpide_exit();
#endif
-#ifdef CONFIG_PROC_FS
proc_ide_destroy();
-#endif
bus_unregister(&ide_bus_type);
}
projects / linux-2.6-omap-h63xx.git / blobdiff