EXPORT_SYMBOL(ide_wait_stat);
+/**
+ * ide_in_drive_list - look for drive in black/white list
+ * @id: drive identifier
+ * @drive_table: list to inspect
+ *
+ * Look for a drive in the blacklist and the whitelist tables
+ * Returns 1 if the drive is found in the table.
+ */
+
+int ide_in_drive_list(struct hd_driveid *id, const struct drive_list_entry *drive_table)
+{
+ for ( ; drive_table->id_model; drive_table++)
+ if ((!strcmp(drive_table->id_model, id->model)) &&
+ (!drive_table->id_firmware ||
+ strstr(id->fw_rev, drive_table->id_firmware)))
+ return 1;
+ return 0;
+}
+
+EXPORT_SYMBOL_GPL(ide_in_drive_list);
+
+/*
+ * Early UDMA66 devices don't set bit14 to 1, only bit13 is valid.
+ * We list them here and depend on the device side cable detection for them.
+ */
+static const struct drive_list_entry ivb_list[] = {
+ { "QUANTUM FIREBALLlct10 05" , "A03.0900" },
+ { NULL , NULL }
+};
+
/*
* All hosts that use the 80c ribbon must use!
* The name is derived from upper byte of word 93 and the 80c ribbon.
*/
u8 eighty_ninty_three (ide_drive_t *drive)
{
- if(HWIF(drive)->udma_four == 0)
- return 0;
+ ide_hwif_t *hwif = drive->hwif;
+ struct hd_driveid *id = drive->id;
+ int ivb = ide_in_drive_list(id, ivb_list);
- /* Check for SATA but only if we are ATA5 or higher */
- if (drive->id->hw_config == 0 && (drive->id->major_rev_num & 0x7FE0))
+ if (hwif->cbl == ATA_CBL_PATA40_SHORT)
return 1;
- if (!(drive->id->hw_config & 0x6000))
- return 0;
-#ifndef CONFIG_IDEDMA_IVB
- if(!(drive->id->hw_config & 0x4000))
- return 0;
-#endif /* CONFIG_IDEDMA_IVB */
+
+ if (ivb)
+ printk(KERN_DEBUG "%s: skipping word 93 validity check\n",
+ drive->name);
+
+ if (hwif->cbl != ATA_CBL_PATA80 && !ivb)
+ goto no_80w;
+
+ if (ide_dev_is_sata(id))
+ return 1;
+
/*
* FIXME:
* - change master/slave IDENTIFY order
- * - force bit13 (80c cable present) check
+ * - force bit13 (80c cable present) check also for !ivb devices
* (unless the slave device is pre-ATA3)
*/
- return 1;
-}
+#ifndef CONFIG_IDEDMA_IVB
+ if ((id->hw_config & 0x4000) || (ivb && (id->hw_config & 0x2000)))
+#else
+ if (id->hw_config & 0x6000)
+#endif
+ return 1;
-EXPORT_SYMBOL(eighty_ninty_three);
+no_80w:
+ if (drive->udma33_warned == 1)
+ return 0;
+
+ printk(KERN_WARNING "%s: %s side 80-wire cable detection failed, "
+ "limiting max speed to UDMA33\n",
+ drive->name,
+ hwif->cbl == ATA_CBL_PATA80 ? "drive" : "host");
+
+ drive->udma33_warned = 1;
+
+ return 0;
+}
int ide_ata66_check (ide_drive_t *drive, ide_task_t *args)
{
if ((args->tfRegister[IDE_COMMAND_OFFSET] == WIN_SETFEATURES) &&
(args->tfRegister[IDE_SECTOR_OFFSET] > XFER_UDMA_2) &&
(args->tfRegister[IDE_FEATURE_OFFSET] == SETFEATURES_XFER)) {
-#ifndef CONFIG_IDEDMA_IVB
- if ((drive->id->hw_config & 0x6000) == 0) {
-#else /* !CONFIG_IDEDMA_IVB */
- if (((drive->id->hw_config & 0x2000) == 0) ||
- ((drive->id->hw_config & 0x4000) == 0)) {
-#endif /* CONFIG_IDEDMA_IVB */
- printk("%s: Speed warnings UDMA 3/4/5 is not "
- "functional.\n", drive->name);
- return 1;
- }
- if (!HWIF(drive)->udma_four) {
- printk("%s: Speed warnings UDMA 3/4/5 is not "
- "functional.\n",
- HWIF(drive)->name);
+ if (eighty_ninty_three(drive) == 0) {
+ printk(KERN_WARNING "%s: UDMA speeds >UDMA33 cannot "
+ "be set\n", drive->name);
return 1;
}
}
+
return 0;
}
hwif->OUTB(drive->ctl | 2, IDE_CONTROL_REG);
hwif->OUTB(speed, IDE_NSECTOR_REG);
hwif->OUTB(SETFEATURES_XFER, IDE_FEATURE_REG);
- hwif->OUTB(WIN_SETFEATURES, IDE_COMMAND_REG);
+ hwif->OUTBSYNC(drive, WIN_SETFEATURES, IDE_COMMAND_REG);
if ((IDE_CONTROL_REG) && (drive->quirk_list == 2))
hwif->OUTB(drive->ctl, IDE_CONTROL_REG);
udelay(1);
*/
for (i = 0; i < 10; i++) {
udelay(1);
- if (OK_STAT((stat = hwif->INB(IDE_STATUS_REG)), DRIVE_READY, BUSY_STAT|DRQ_STAT|ERR_STAT)) {
+ if (OK_STAT((stat = hwif->INB(IDE_STATUS_REG)), drive->ready_stat, BUSY_STAT|DRQ_STAT|ERR_STAT)) {
error = 0;
break;
}