#endif
}
-/* FIXME: exported for use by the USB storage (isd200.c) code only */
-EXPORT_SYMBOL(ide_fix_driveid);
+/*
+ * ide_fixstring() cleans up and (optionally) byte-swaps a text string,
+ * removing leading/trailing blanks and compressing internal blanks.
+ * It is primarily used to tidy up the model name/number fields as
+ * returned by the WIN_[P]IDENTIFY commands.
+ */
void ide_fixstring (u8 *s, const int bytecount, const int byteswap)
{
* setting a timer to wake up at half second intervals thereafter,
* until timeout is achieved, before timing out.
*/
-int __ide_wait_stat(ide_drive_t *drive, u8 good, u8 bad, unsigned long timeout, u8 *rstat)
+static int __ide_wait_stat(ide_drive_t *drive, u8 good, u8 bad, unsigned long timeout, u8 *rstat)
{
ide_hwif_t *hwif = drive->hwif;
unsigned long flags;
/*
* Early UDMA66 devices don't set bit14 to 1, only bit13 is valid.
* We list them here and depend on the device side cable detection for them.
+ *
+ * Some optical devices with the buggy firmwares have the same problem.
*/
static const struct drive_list_entry ivb_list[] = {
{ "QUANTUM FIREBALLlct10 05" , "A03.0900" },
+ { "TSSTcorp CDDVDW SH-S202J" , "SB00" },
{ NULL , NULL }
};
/*
* FIXME:
- * - change master/slave IDENTIFY order
* - force bit13 (80c cable present) check also for !ivb devices
* (unless the slave device is pre-ATA3)
*/
-#ifndef CONFIG_IDEDMA_IVB
if ((id->hw_config & 0x4000) || (ivb && (id->hw_config & 0x2000)))
-#else
- if (id->hw_config & 0x6000)
-#endif
return 1;
no_80w:
}
#endif /* CONFIG_BLK_DEV_IDEDMA */
-/*
- * Update the
- */
-int ide_driveid_update (ide_drive_t *drive)
+int ide_driveid_update(ide_drive_t *drive)
{
- ide_hwif_t *hwif = HWIF(drive);
+ ide_hwif_t *hwif = drive->hwif;
struct hd_driveid *id;
-#if 0
- id = kmalloc(SECTOR_WORDS*4, GFP_ATOMIC);
- if (!id)
- return 0;
-
- taskfile_lib_get_identify(drive, (char *)&id);
+ unsigned long timeout, flags;
- ide_fix_driveid(id);
- if (id) {
- drive->id->dma_ultra = id->dma_ultra;
- drive->id->dma_mword = id->dma_mword;
- drive->id->dma_1word = id->dma_1word;
- /* anything more ? */
- kfree(id);
- }
- return 1;
-#else
/*
* Re-read drive->id for possible DMA mode
* change (copied from ide-probe.c)
*/
- unsigned long timeout, flags;
SELECT_MASK(drive, 1);
if (IDE_CONTROL_REG)
}
return 1;
-#endif
}
int ide_config_drive_speed(ide_drive_t *drive, u8 speed)
{
ide_hwif_t *hwif = drive->hwif;
- int error;
+ int error = 0;
u8 stat;
// while (HWGROUP(drive)->busy)
// msleep(50);
#ifdef CONFIG_BLK_DEV_IDEDMA
- if (hwif->ide_dma_check) /* check if host supports DMA */
+ if (hwif->ide_dma_on) /* check if host supports DMA */
hwif->dma_host_off(drive);
#endif
+ /* Skip setting PIO flow-control modes on pre-EIDE drives */
+ if ((speed & 0xf8) == XFER_PIO_0 && !(drive->id->capability & 0x08))
+ goto skip;
+
/*
* Don't use ide_wait_cmd here - it will
* attempt to set_geometry and recalibrate,
drive->id->dma_mword &= ~0x0F00;
drive->id->dma_1word &= ~0x0F00;
+ skip:
#ifdef CONFIG_BLK_DEV_IDEDMA
if (speed >= XFER_SW_DMA_0)
hwif->dma_host_on(drive);
- else if (hwif->ide_dma_check) /* check if host supports DMA */
+ else if (hwif->ide_dma_on) /* check if host supports DMA */
hwif->dma_off_quietly(drive);
#endif
return error;
}
-EXPORT_SYMBOL(ide_config_drive_speed);
-
-
/*
* This should get invoked any time we exit the driver to
* wait for an interrupt response from a drive. handler() points