# Select HAVE_IDE if IDE is supported
config HAVE_IDE
- def_bool n
+ bool
menuconfig IDE
tristate "ATA/ATAPI/MFM/RLL support"
if IDE
-config BLK_DEV_IDE
- tristate "Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support"
- ---help---
- If you say Y here, you will use the full-featured IDE driver to
- control up to ten ATA/IDE interfaces, each being able to serve a
- "master" and a "slave" device, for a total of up to twenty ATA/IDE
- disk/cdrom/tape/floppy drives.
-
- Useful information about large (>540 MB) IDE disks, multiple
- interfaces, what to do if ATA/IDE devices are not automatically
- detected, sound card ATA/IDE ports, module support, and other
- topics, is contained in <file:Documentation/ide/ide.txt>. For detailed
- information about hard drives, consult the Disk-HOWTO and the
- Multi-Disk-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To fine-tune ATA/IDE drive/interface parameters for improved
- performance, look for the hdparm package at
- <ftp://ibiblio.org/pub/Linux/system/hardware/>.
-
- To compile this driver as a module, choose M here and read
- <file:Documentation/ide/ide.txt>. The module will be called ide-mod.
- Do not compile this driver as a module if your root file system (the
- one containing the directory /) is located on an IDE device.
-
- If you have one or more IDE drives, say Y or M here. If your system
- has no IDE drives, or if memory requirements are really tight, you
- could say N here, and select the "Old hard disk driver" below
- instead to save about 13 KB of memory in the kernel.
-
-if BLK_DEV_IDE
-
comment "Please see Documentation/ide/ide.txt for help/info on IDE drives"
config IDE_TIMINGS
If unsure, say N.
-config BLK_DEV_IDEDISK
- tristate "Include IDE/ATA-2 DISK support"
- ---help---
- This will include enhanced support for MFM/RLL/IDE hard disks. If
- you have a MFM/RLL/IDE disk, and there is no special reason to use
- the old hard disk driver instead, say Y. If you have an SCSI-only
- system, you can say N here.
+config IDE_GD
+ tristate "generic ATA/ATAPI disk support"
+ default y
+ help
+ Support for ATA/ATAPI disks (including ATAPI floppy drives).
- To compile this driver as a module, choose M here: the
- module will be called ide-disk.
- Do not compile this driver as a module if your root file system
- (the one containing the directory /) is located on the IDE disk.
+ To compile this driver as a module, choose M here.
+ The module will be called ide-gd_mod.
+
+ If unsure, say Y.
+
+config IDE_GD_ATA
+ bool "ATA disk support"
+ depends on IDE_GD
+ default y
+ help
+ This will include support for ATA hard disks.
If unsure, say Y.
+config IDE_GD_ATAPI
+ bool "ATAPI floppy support"
+ depends on IDE_GD
+ select IDE_ATAPI
+ help
+ This will include support for ATAPI floppy drives
+ (i.e. Iomega ZIP or MKE LS-120).
+
+ For information about jumper settings and the question
+ of when a ZIP drive uses a partition table, see
+ <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.
+
+ If unsure, say N.
+
config BLK_DEV_IDECS
tristate "PCMCIA IDE support"
depends on PCMCIA
To compile this driver as a module, choose M here: the
module will be called ide-tape.
-config BLK_DEV_IDEFLOPPY
- tristate "Include IDE/ATAPI FLOPPY support"
- select IDE_ATAPI
- ---help---
- If you have an IDE floppy drive which uses the ATAPI protocol,
- answer Y. ATAPI is a newer protocol used by IDE CD-ROM/tape/floppy
- drives, similar to the SCSI protocol.
-
- The LS-120 and the IDE/ATAPI Iomega ZIP drive are also supported by
- this driver. For information about jumper settings and the question
- of when a ZIP drive uses a partition table, see
- <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.
- (ATAPI PD-CD/CDR drives are not supported by this driver; support
- for PD-CD/CDR drives is available if you answer Y to
- "SCSI emulation support", below).
-
- If you say Y here, the FLOPPY drive will be identified along with
- other IDE devices, as "hdb" or "hdc", or something similar (check
- the boot messages with dmesg).
-
- To compile this driver as a module, choose M here: the
- module will be called ide-floppy.
-
config BLK_DEV_IDESCSI
tristate "SCSI emulation support (DEPRECATED)"
depends on SCSI
config IDEPCI_PCIBUS_ORDER
bool "Probe IDE PCI devices in the PCI bus order (DEPRECATED)"
- depends on BLK_DEV_IDE=y && BLK_DEV_IDEPCI
+ depends on IDE=y && BLK_DEV_IDEPCI
default y
help
Probe IDE PCI devices in the order in which they appear on the
config BLK_DEV_IDE_PMAC
tristate "PowerMac on-board IDE support"
- depends on PPC_PMAC && IDE=y && BLK_DEV_IDE=y
+ depends on PPC_PMAC && IDE=y
select IDE_TIMINGS
help
This driver provides support for the on-board IDE controller on
def_bool BLK_DEV_IDEDMA_SFF || BLK_DEV_IDEDMA_PMAC || \
BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
-endif
-
endif # IDE
projects / linux-2.6-omap-h63xx.git / blobdiff