If unsure, say N.
-config BLK_DEV_IDEDISK
- tristate "Include IDE/ATA-2 DISK support"
- ---help---
- This will include enhanced support for MFM/RLL/IDE hard disks. If
- you have a MFM/RLL/IDE disk, and there is no special reason to use
- the old hard disk driver instead, say Y. If you have an SCSI-only
- system, you can say N here.
+config IDE_GD
+ tristate "generic ATA/ATAPI disk support"
+ default y
+ help
+ Support for ATA/ATAPI disks (including ATAPI floppy drives).
- To compile this driver as a module, choose M here: the
- module will be called ide-disk.
- Do not compile this driver as a module if your root file system
- (the one containing the directory /) is located on the IDE disk.
+ To compile this driver as a module, choose M here.
+ The module will be called ide-gd_mod.
If unsure, say Y.
+config IDE_GD_ATA
+ bool "ATA disk support"
+ depends on IDE_GD
+ default y
+ help
+ This will include support for ATA hard disks.
+
+ If unsure, say Y.
+
+config IDE_GD_ATAPI
+ bool "ATAPI floppy support"
+ depends on IDE_GD
+ select IDE_ATAPI
+ help
+ This will include support for ATAPI floppy drives
+ (i.e. Iomega ZIP or MKE LS-120).
+
+ For information about jumper settings and the question
+ of when a ZIP drive uses a partition table, see
+ <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.
+
+ If unsure, say N.
+
config BLK_DEV_IDECS
tristate "PCMCIA IDE support"
depends on PCMCIA
To compile this driver as a module, choose M here: the
module will be called ide-tape.
-config BLK_DEV_IDEFLOPPY
- tristate "Include IDE/ATAPI FLOPPY support"
- select IDE_ATAPI
- ---help---
- If you have an IDE floppy drive which uses the ATAPI protocol,
- answer Y. ATAPI is a newer protocol used by IDE CD-ROM/tape/floppy
- drives, similar to the SCSI protocol.
-
- The LS-120 and the IDE/ATAPI Iomega ZIP drive are also supported by
- this driver. For information about jumper settings and the question
- of when a ZIP drive uses a partition table, see
- <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.
- (ATAPI PD-CD/CDR drives are not supported by this driver; support
- for PD-CD/CDR drives is available if you answer Y to
- "SCSI emulation support", below).
-
- If you say Y here, the FLOPPY drive will be identified along with
- other IDE devices, as "hdb" or "hdc", or something similar (check
- the boot messages with dmesg).
-
- To compile this driver as a module, choose M here: the
- module will be called ide-floppy.
-
config BLK_DEV_IDESCSI
tristate "SCSI emulation support (DEPRECATED)"
depends on SCSI
# TODO: split it on per host driver config options (or module parameters)
config BLK_DEV_OFFBOARD
bool "Boot off-board chipsets first support (DEPRECATED)"
- depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT34X || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
+ depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
help
Normally, IDE controllers built into the motherboard (on-board
controllers) are assigned to ide0 and ide1 while those on add-in PCI
It is safe to say Y to this question.
-config BLK_DEV_HPT34X
- tristate "HPT34X chipset support"
- depends on BROKEN
- select BLK_DEV_IDEDMA_PCI
- help
- This driver adds up to 4 more EIDE devices sharing a single
- interrupt. The HPT343 chipset in its current form is a non-bootable
- controller; the HPT345/HPT363 chipset is a bootable (needs BIOS FIX)
- PCI UDMA controllers. This driver requires dynamic tuning of the
- chipset during the ide-probe at boot time. It is reported to support
- DVD II drives, by the manufacturer.
-
-config HPT34X_AUTODMA
- bool "HPT34X AUTODMA support (EXPERIMENTAL)"
- depends on BLK_DEV_HPT34X && EXPERIMENTAL
- help
- This is a dangerous thing to attempt currently! Please read the
- comments at the top of <file:drivers/ide/pci/hpt34x.c>. If you say Y
- here, then say Y to "Use DMA by default when available" as well.
-
- If unsure, say N.
-
config BLK_DEV_HPT366
tristate "HPT36X/37X chipset support"
select BLK_DEV_IDEDMA_PCI
endif
+# TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF
config BLK_DEV_IDE_PMAC
tristate "PowerMac on-board IDE support"
depends on PPC_PMAC && IDE=y
select IDE_TIMINGS
+ select BLK_DEV_IDEDMA_PCI
help
This driver provides support for the on-board IDE controller on
most of the recent Apple Power Macintoshes and PowerBooks.
CD-ROM on hda. This option changes this to more natural hda for
hard disk and hdc for CD-ROM.
-config BLK_DEV_IDEDMA_PMAC
- bool "PowerMac IDE DMA support"
- depends on BLK_DEV_IDE_PMAC
- select BLK_DEV_IDEDMA_PCI
- help
- This option allows the driver for the on-board IDE controller on
- Power Macintoshes and PowerBooks to use DMA (direct memory access)
- to transfer data to and from memory. Saying Y is safe and improves
- performance.
-
config BLK_DEV_IDE_AU1XXX
bool "IDE for AMD Alchemy Au1200"
depends on SOC_AU1200
default "128"
depends on BLK_DEV_IDE_AU1XXX
+config BLK_DEV_IDE_TX4938
+ tristate "TX4938 internal IDE support"
+ depends on SOC_TX4938
+ select IDE_TIMINGS
+
+config BLK_DEV_IDE_TX4939
+ tristate "TX4939 internal IDE support"
+ depends on SOC_TX4939
+ select BLK_DEV_IDEDMA_SFF
+
config IDE_ARM
tristate "ARM IDE support"
depends on ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
endif
config BLK_DEV_IDEDMA
- def_bool BLK_DEV_IDEDMA_SFF || BLK_DEV_IDEDMA_PMAC || \
+ def_bool BLK_DEV_IDEDMA_SFF || \
BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
endif # IDE
projects / linux-2.6-omap-h63xx.git / blobdiff