This driver can also be built as a module. If so, the module
will be called ds1682.
-config AT24
- tristate "EEPROMs from most vendors"
- depends on SYSFS && EXPERIMENTAL
- help
- Enable this driver to get read/write support to most I2C EEPROMs,
- after you configure the driver to know about each EEPROM on
- your target board. Use these generic chip names, instead of
- vendor-specific ones like at24c64 or 24lc02:
-
- 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
- 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
-
- Unless you like data loss puzzles, always be sure that any chip
- you configure as a 24c32 (32 kbit) or larger is NOT really a
- 24c16 (16 kbit) or smaller, and vice versa. Marking the chip
- as read-only won't help recover from this. Also, if your chip
- has any software write-protect mechanism you may want to review the
- code to make sure this driver won't turn it on by accident.
-
- If you use this with an SMBus adapter instead of an I2C adapter,
- full functionality is not available. Only smaller devices are
- supported (24c16 and below, max 4 kByte).
-
- This driver can also be built as a module. If so, the module
- will be called at24.
-
-config SENSORS_EEPROM
- tristate "EEPROM reader"
- depends on EXPERIMENTAL
- help
- If you say yes here you get read-only access to the EEPROM data
- available on modern memory DIMMs and Sony Vaio laptops. Such
- EEPROMs could theoretically be available on other devices as well.
-
- This driver can also be built as a module. If so, the module
- will be called eeprom.
-
config SENSORS_PCF8574
tristate "Philips PCF8574 and PCF8574A (DEPRECATED)"
depends on EXPERIMENTAL && GPIO_PCF857X = "n"
These devices are hard to detect and rarely found on mainstream
hardware. If unsure, say N.
-config ISP1301_OMAP
- tristate "Philips ISP1301 with OMAP OTG"
- depends on ARCH_OMAP_OTG
+config TWL4030_MADC
+ tristate "TWL4030 MADC Driver"
+ depends on TWL4030_CORE
help
- If you say yes here you get support for the Philips ISP1301
- USB-On-The-Go transceiver working with the OMAP OTG controller.
- The ISP1301 is used in products including H2 and H3 development
- boards for Texas Instruments OMAP processors.
-
- This driver can also be built as a module. If so, the module
- will be called isp1301_omap.
+ The TWL4030 Monitoring ADC driver enables the host
+ processor to monitor analog signals using analog-to-digital
+ conversions on the input source. TWL4030 MADC provides the
+ following features:
+ - Single 10-bit ADC with successive approximation register (SAR) conversion;
+ - Analog multiplexer for 16 inputs;
+ - Seven (of the 16) inputs are freely available;
+ - Battery voltage monitoring;
+ - Concurrent conversion request management;
+ - Interrupt signal to Primary Interrupt Handler;
+ - Averaging feature;
+ - Selective enable/disable of the averaging feature.
+
+ Say 'y' here to statically link this module into the kernel or 'm'
+ to build it as a dinamically loadable module. The module will be
+ called twl4030-madc.ko
+
+config TWL4030_PWRBUTTON
+ tristate "TWL4030 Power button Driver"
+ depends on TWL4030_CORE
+
+config TWL4030_POWEROFF
+ tristate "TWL4030 device poweroff"
+ depends on TWL4030_CORE
config SENSORS_MAX6875
tristate "Maxim MAX6875 Power supply supervisor"
This driver can also be built as a module. If so, the module
will be called tsl2550.
-config MCU_MPC8349EMITX
- tristate "MPC8349E-mITX MCU driver"
- depends on I2C && PPC_83xx
- select GENERIC_GPIO
- select ARCH_REQUIRE_GPIOLIB
+config SENSORS_TSL2563
+ tristate "Taos TSL2563 ambient light sensor"
+ depends on I2C && HWMON
+ help
+ If you say yes here you get support for the Taos TSL2563
+ ambient light sensor.
+
+ This driver can also be built as a module. If so, the module
+ will be called tsl2563.
+
+config LP5521
+ tristate "LP5521 LED driver chip"
+ depends on I2C
+ help
+ If you say yes here you get support for the National Semiconductor
+ LP5521 LED driver.
+
+config MENELAUS
+ bool "TWL92330/Menelaus PM chip"
+ depends on I2C=y && ARCH_OMAP24XX
help
- Say Y here to enable soft power-off functionality on the Freescale
- boards with the MPC8349E-mITX-compatible MCU chips. This driver will
- also register MCU GPIOs with the generic GPIO API, so you'll able
- to use MCU pins as GPIOs.
+ If you say yes here you get support for the Texas Instruments
+ TWL92330/Menelaus Power Management chip. This include voltage
+ regulators, Dual slot memory card tranceivers, real-time clock
+ and other features that are often used in portable devices like
+ cell phones and PDAs.
endmenu
projects / linux-2.6-omap-h63xx.git / blobdiff