*
* TODO/CHECK
* Cannot have ATAPI on both master & slave for rev < c2 (???) but
- * otherwise should do atapi DMA.
+ * otherwise should do atapi DMA (For now for old we do PIO only for
+ * ATAPI)
+ * Review Sunblade workaround.
*/
#include <linux/kernel.h>
#include <linux/dmi.h>
#define DRV_NAME "pata_ali"
-#define DRV_VERSION "0.7.5"
+#define DRV_VERSION "0.7.8"
static int ali_atapi_dma = 0;
module_param_named(atapi_dma, ali_atapi_dma, int, 0644);
MODULE_PARM_DESC(atapi_dma, "Enable ATAPI DMA (0=disable, 1=enable)");
+static struct pci_dev *ali_isa_bridge;
+
/*
* Cable special cases
*/
pci_read_config_byte(pdev, pio_fifo, &fifo);
fifo &= ~(0x0F << shift);
- if (on)
- fifo |= (on << shift);
+ fifo |= (on << shift);
pci_write_config_byte(pdev, pio_fifo, fifo);
}
return 0;
}
+static void ali_c2_c3_postreset(struct ata_link *link, unsigned int *classes)
+{
+ u8 r;
+ int port_bit = 4 << link->ap->port_no;
+
+ /* If our bridge is an ALI 1533 then do the extra work */
+ if (ali_isa_bridge) {
+ /* Tristate and re-enable the bus signals */
+ pci_read_config_byte(ali_isa_bridge, 0x58, &r);
+ r &= ~port_bit;
+ pci_write_config_byte(ali_isa_bridge, 0x58, r);
+ r |= port_bit;
+ pci_write_config_byte(ali_isa_bridge, 0x58, r);
+ }
+ ata_sff_postreset(link, classes);
+}
+
static struct scsi_host_template ali_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
.inherits = &ata_sff_port_ops,
.cable_detect = ata_cable_40wire,
.set_piomode = ali_set_piomode,
+ .sff_data_xfer = ata_sff_data_xfer32,
};
static const struct ata_port_operations ali_dma_base_ops = {
- .inherits = &ata_bmdma_port_ops,
+ .inherits = &ata_bmdma32_port_ops,
.set_piomode = ali_set_piomode,
.set_dmamode = ali_set_dmamode,
};
.check_atapi_dma = ali_check_atapi_dma,
.cable_detect = ali_c2_cable_detect,
.dev_config = ali_lock_sectors,
+ .postreset = ali_c2_c3_postreset,
+};
+
+/*
+ * Port operations for DMA capable ALi with cable detect
+ */
+static struct ata_port_operations ali_c4_port_ops = {
+ .inherits = &ali_dma_base_ops,
+ .check_atapi_dma = ali_check_atapi_dma,
+ .cable_detect = ali_c2_cable_detect,
+ .dev_config = ali_lock_sectors,
};
/*
static void ali_init_chipset(struct pci_dev *pdev)
{
u8 tmp;
- struct pci_dev *north, *isa_bridge;
+ struct pci_dev *north;
/*
* The chipset revision selects the driver operations and
* mode data.
*/
- if (pdev->revision >= 0x20 && pdev->revision < 0xC2) {
- /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
- pci_read_config_byte(pdev, 0x4B, &tmp);
- /* Clear CD-ROM DMA write bit */
- tmp &= 0x7F;
- pci_write_config_byte(pdev, 0x4B, tmp);
- } else if (pdev->revision >= 0xC2) {
- /* Enable cable detection logic */
+ if (pdev->revision <= 0x20) {
+ pci_read_config_byte(pdev, 0x53, &tmp);
+ tmp |= 0x03;
+ pci_write_config_byte(pdev, 0x53, tmp);
+ } else {
+ pci_read_config_byte(pdev, 0x4a, &tmp);
+ pci_write_config_byte(pdev, 0x4a, tmp | 0x20);
pci_read_config_byte(pdev, 0x4B, &tmp);
- pci_write_config_byte(pdev, 0x4B, tmp | 0x08);
- }
- north = pci_get_bus_and_slot(0, PCI_DEVFN(0,0));
- isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
-
- if (north && north->vendor == PCI_VENDOR_ID_AL && isa_bridge) {
- /* Configure the ALi bridge logic. For non ALi rely on BIOS.
- Set the south bridge enable bit */
- pci_read_config_byte(isa_bridge, 0x79, &tmp);
- if (pdev->revision == 0xC2)
- pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04);
- else if (pdev->revision > 0xC2 && pdev->revision < 0xC5)
- pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02);
- }
- if (pdev->revision >= 0x20) {
+ if (pdev->revision < 0xC2)
+ /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */
+ /* Clear CD-ROM DMA write bit */
+ tmp &= 0x7F;
+ /* Cable and UDMA */
+ pci_write_config_byte(pdev, 0x4B, tmp | 0x09);
/*
* CD_ROM DMA on (0x53 bit 0). Enable this even if we want
* to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control
* via 0x54/55.
*/
pci_read_config_byte(pdev, 0x53, &tmp);
- if (pdev->revision <= 0x20)
- tmp &= ~0x02;
if (pdev->revision >= 0xc7)
tmp |= 0x03;
else
tmp |= 0x01; /* CD_ROM enable for DMA */
pci_write_config_byte(pdev, 0x53, tmp);
}
- pci_dev_put(isa_bridge);
+ north = pci_get_bus_and_slot(0, PCI_DEVFN(0,0));
+ if (north && north->vendor == PCI_VENDOR_ID_AL && ali_isa_bridge) {
+ /* Configure the ALi bridge logic. For non ALi rely on BIOS.
+ Set the south bridge enable bit */
+ pci_read_config_byte(ali_isa_bridge, 0x79, &tmp);
+ if (pdev->revision == 0xC2)
+ pci_write_config_byte(ali_isa_bridge, 0x79, tmp | 0x04);
+ else if (pdev->revision > 0xC2 && pdev->revision < 0xC5)
+ pci_write_config_byte(ali_isa_bridge, 0x79, tmp | 0x02);
+ }
pci_dev_put(north);
ata_pci_bmdma_clear_simplex(pdev);
}
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA5,
- .port_ops = &ali_c2_port_ops
+ .port_ops = &ali_c4_port_ops
};
/* Revision 0xC5 is UDMA133 with LBA48 DMA */
static const struct ata_port_info info_c5 = {
const struct ata_port_info *ppi[] = { NULL, NULL };
u8 tmp;
- struct pci_dev *isa_bridge;
int rc;
rc = pcim_enable_device(pdev);
ali_init_chipset(pdev);
- isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
- if (isa_bridge && pdev->revision >= 0x20 && pdev->revision < 0xC2) {
+ if (ali_isa_bridge && pdev->revision >= 0x20 && pdev->revision < 0xC2) {
/* Are we paired with a UDMA capable chip */
- pci_read_config_byte(isa_bridge, 0x5E, &tmp);
+ pci_read_config_byte(ali_isa_bridge, 0x5E, &tmp);
if ((tmp & 0x1E) == 0x12)
ppi[0] = &info_20_udma;
}
- pci_dev_put(isa_bridge);
return ata_pci_sff_init_one(pdev, ppi, &ali_sht, NULL);
}
static int __init ali_init(void)
{
- return pci_register_driver(&ali_pci_driver);
+ int ret;
+ ali_isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
+
+ ret = pci_register_driver(&ali_pci_driver);
+ if (ret < 0)
+ pci_dev_put(ali_isa_bridge);
+ return ret;
}
static void __exit ali_exit(void)
{
pci_unregister_driver(&ali_pci_driver);
+ pci_dev_put(ali_isa_bridge);
}
projects / linux-2.6-omap-h63xx.git / blobdiff