[PATCH] Remove KERN_INFO from middle of printk line

[linux-2.6-omap-h63xx.git] / arch / x86_64 / kernel / mpparse.c

diff --git a/arch/x86_64/kernel/mpparse.c b/arch/x86_64/kernel/mpparse.c
index f16d38d09dafeadcafc6d1e6413617c96eeeb8d4..9013a90b5c2e69aebbcc038c2abc57e84d715c49 100644 (file)
--- a/arch/x86_64/kernel/mpparse.c
+++ b/arch/x86_64/kernel/mpparse.c
@@ -42,7 +42,7 @@ int acpi_found_madt;
  * Various Linux-internal data structures created from the
  * MP-table.
  */
-int apic_version [MAX_APICS];
+unsigned char apic_version [MAX_APICS];
 unsigned char mp_bus_id_to_type [MAX_MP_BUSSES] = { [0 ... MAX_MP_BUSSES-1] = -1 };
 int mp_bus_id_to_pci_bus [MAX_MP_BUSSES] = { [0 ... MAX_MP_BUSSES-1] = -1 };
 
@@ -65,7 +65,9 @@ unsigned long mp_lapic_addr = 0;
 /* Processor that is doing the boot up */
 unsigned int boot_cpu_id = -1U;
 /* Internal processor count */
-static unsigned int num_processors = 0;
+unsigned int num_processors __initdata = 0;
+
+unsigned disabled_cpus __initdata;
 
 /* Bitmask of physically existing CPUs */
 physid_mask_t phys_cpu_present_map = PHYSID_MASK_NONE;
@@ -106,11 +108,14 @@ static int __init mpf_checksum(unsigned char *mp, int len)
 
 static void __init MP_processor_info (struct mpc_config_processor *m)
 {
-       int ver, cpu;
+       int cpu;
+       unsigned char ver;
        static int found_bsp=0;
 
-       if (!(m->mpc_cpuflag & CPU_ENABLED))
+       if (!(m->mpc_cpuflag & CPU_ENABLED)) {
+               disabled_cpus++;
                return;
+       }
 
        printk(KERN_INFO "Processor #%d %d:%d APIC version %d\n",
                m->mpc_apicid,
@@ -129,12 +134,14 @@ static void __init MP_processor_info (struct mpc_config_processor *m)
        }
 
        cpu = num_processors++;
-
-       if (m->mpc_apicid > MAX_APICS) {
+       
+#if MAX_APICS < 255    
+       if ((int)m->mpc_apicid > MAX_APICS) {
                printk(KERN_ERR "Processor #%d INVALID. (Max ID: %d).\n",
                        m->mpc_apicid, MAX_APICS);
                return;
        }
+#endif
        ver = m->mpc_apicver;
 
        physid_set(m->mpc_apicid, phys_cpu_present_map);
@@ -218,7 +225,7 @@ static void __init MP_intsrc_info (struct mpc_config_intsrc *m)
                        m->mpc_irqtype, m->mpc_irqflag & 3,
                        (m->mpc_irqflag >> 2) & 3, m->mpc_srcbus,
                        m->mpc_srcbusirq, m->mpc_dstapic, m->mpc_dstirq);
-       if (++mp_irq_entries == MAX_IRQ_SOURCES)
+       if (++mp_irq_entries >= MAX_IRQ_SOURCES)
                panic("Max # of irq sources exceeded!!\n");
 }
 
@@ -281,9 +288,9 @@ static int __init smp_read_mpc(struct mp_config_table *mpc)
 
        memcpy(str,mpc->mpc_productid,12);
        str[12]=0;
-       printk(KERN_INFO "Product ID: %s ",str);
+       printk("Product ID: %s ",str);
 
-       printk(KERN_INFO "APIC at: 0x%X\n",mpc->mpc_lapic);
+       printk("APIC at: 0x%X\n",mpc->mpc_lapic);
 
        /* save the local APIC address, it might be non-default */
        if (!acpi_lapic)
@@ -549,7 +556,7 @@ void __init get_smp_config (void)
                 * Read the physical hardware table.  Anything here will
                 * override the defaults.
                 */
-               if (!smp_read_mpc((void *)(unsigned long)mpf->mpf_physptr)) {
+               if (!smp_read_mpc(phys_to_virt(mpf->mpf_physptr))) {
                        smp_found_config = 0;
                        printk(KERN_ERR "BIOS bug, MP table errors detected!...\n");
                        printk(KERN_ERR "... disabling SMP support. (tell your hw vendor)\n");
@@ -908,7 +915,7 @@ void __init mp_config_acpi_legacy_irqs (void)
 
 #define MAX_GSI_NUM    4096
 
-int mp_register_gsi(u32 gsi, int edge_level, int active_high_low)
+int mp_register_gsi(u32 gsi, int triggering, int polarity)
 {
        int                     ioapic = -1;
        int                     ioapic_pin = 0;
@@ -957,7 +964,7 @@ int mp_register_gsi(u32 gsi, int edge_level, int active_high_low)
 
        mp_ioapic_routing[ioapic].pin_programmed[idx] |= (1<<bit);
 
-       if (edge_level) {
+       if (triggering == ACPI_LEVEL_SENSITIVE) {
                /*
                 * For PCI devices assign IRQs in order, avoiding gaps
                 * due to unused I/O APIC pins.
@@ -979,8 +986,8 @@ int mp_register_gsi(u32 gsi, int edge_level, int active_high_low)
        }
 
        io_apic_set_pci_routing(ioapic, ioapic_pin, gsi,
-               edge_level == ACPI_EDGE_SENSITIVE ? 0 : 1,
-               active_high_low == ACPI_ACTIVE_HIGH ? 0 : 1);
+               triggering == ACPI_EDGE_SENSITIVE ? 0 : 1,
+               polarity == ACPI_ACTIVE_HIGH ? 0 : 1);
        return gsi;
 }