/*
*
- * Copyright (C) 2001 MontaVista Software, ppopov@mvista.com
+ * Copyright (C) 2001, 2006, 2008 MontaVista Software, <source@mvista.com>
* Copied and modified Carsten Langgaard's time.c
*
* Carsten Langgaard, carstenl@mips.com
#include <linux/mc146818rtc.h>
#include <linux/timex.h>
-static unsigned long r4k_offset; /* Amount to increment compare reg each time */
-static unsigned long r4k_cur; /* What counter should be at next timer irq */
-int no_au1xxx_32khz;
+static int no_au1xxx_32khz;
extern int allow_au1k_wait; /* default off for CP0 Counter */
#ifdef CONFIG_PM
unsigned long wtimer;
#ifdef CONFIG_PM
-irqreturn_t counter0_irq(int irq, void *dev_id)
+static irqreturn_t counter0_irq(int irq, void *dev_id)
{
unsigned long pc0;
int time_elapsed;
return IRQ_HANDLED;
}
+struct irqaction counter0_action = {
+ .handler = counter0_irq,
+ .flags = IRQF_DISABLED,
+ .name = "alchemy-toy",
+ .dev_id = NULL,
+};
+
/* When we wakeup from sleep, we have to "catch up" on all of the
* timer ticks we have missed.
*/
* "wait" is enabled, and we need to detect if the 32KHz isn't present
* but requested......got it? :-) -- Dan
*/
-unsigned long cal_r4koff(void)
+unsigned long calc_clock(void)
{
unsigned long cpu_speed;
unsigned long flags;
while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S);
au_writel(0, SYS_TOYWRITE);
while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S);
+ } else
+ no_au1xxx_32khz = 1;
- cpu_speed = (au_readl(SYS_CPUPLL) & 0x0000003f) *
- AU1000_SRC_CLK;
- }
- else {
- /* The 32KHz oscillator isn't running, so assume there
- * isn't one and grab the processor speed from the PLL.
- * NOTE: some old silicon doesn't allow reading the PLL.
- */
+ /*
+ * On early Au1000, sys_cpupll was write-only. Since these
+ * silicon versions of Au1000 are not sold by AMD, we don't bend
+ * over backwards trying to determine the frequency.
+ */
+ if (cur_cpu_spec[0]->cpu_pll_wo)
+#ifdef CONFIG_SOC_AU1000_FREQUENCY
+ cpu_speed = CONFIG_SOC_AU1000_FREQUENCY;
+#else
+ cpu_speed = 396000000;
+#endif
+ else
cpu_speed = (au_readl(SYS_CPUPLL) & 0x0000003f) * AU1000_SRC_CLK;
- no_au1xxx_32khz = 1;
- }
mips_hpt_frequency = cpu_speed;
// Equation: Baudrate = CPU / (SD * 2 * CLKDIV * 16)
set_au1x00_uart_baud_base(cpu_speed / (2 * ((int)(au_readl(SYS_POWERCTRL)&0x03) + 2) * 16));
spin_unlock_irqrestore(&time_lock, flags);
- return (cpu_speed / HZ);
+ return cpu_speed;
}
-void __init plat_timer_setup(struct irqaction *irq)
+void __init plat_time_init(void)
{
- unsigned int est_freq;
-
- printk("calculating r4koff... ");
- r4k_offset = cal_r4koff();
- printk("%08lx(%d)\n", r4k_offset, (int) r4k_offset);
+ unsigned int est_freq = calc_clock();
- //est_freq = 2*r4k_offset*HZ;
- est_freq = r4k_offset*HZ;
est_freq += 5000; /* round */
est_freq -= est_freq%10000;
printk("CPU frequency %d.%02d MHz\n", est_freq/1000000,
set_au1x00_speed(est_freq);
set_au1x00_lcd_clock(); // program the LCD clock
- r4k_cur = (read_c0_count() + r4k_offset);
- write_c0_compare(r4k_cur);
-
#ifdef CONFIG_PM
/*
* setup counter 0, since it keeps ticking after a
* Check to ensure we really have a 32KHz oscillator before
* we do this.
*/
- if (no_au1xxx_32khz) {
- unsigned int c0_status;
-
+ if (no_au1xxx_32khz)
printk("WARNING: no 32KHz clock found.\n");
-
- /* Ensure we get CPO_COUNTER interrupts.
- */
- c0_status = read_c0_status();
- c0_status |= IE_IRQ5;
- write_c0_status(c0_status);
- }
else {
while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C0S);
au_writel(0, SYS_TOYWRITE);
au_writel(last_match20 + MATCH20_INC, SYS_TOYMATCH2);
au_sync();
while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_M20);
- startup_match20_interrupt(counter0_irq);
+ setup_irq(AU1000_TOY_MATCH2_INT, &counter0_action);
/* We can use the real 'wait' instruction.
*/