[MIPS] Alchemy: don't unmask timer IRQ early

[linux-2.6-omap-h63xx.git] / arch / mips / au1000 / common / time.c

diff --git a/arch/mips/au1000/common/time.c b/arch/mips/au1000/common/time.c
index 2556399708ba452278d2c05c73b319d4fe864750..1966964590ab13830c266120b31d9c2b08155eef 100644 (file)
--- a/arch/mips/au1000/common/time.c
+++ b/arch/mips/au1000/common/time.c
@@ -1,6 +1,6 @@
 /*
  *
- * Copyright (C) 2001 MontaVista Software, ppopov@mvista.com
+ * Copyright (C) 2001, 2006, 2008 MontaVista Software, <source@mvista.com>
  * Copied and modified Carsten Langgaard's time.c
  *
  * Carsten Langgaard, carstenl@mips.com
@@ -67,7 +67,7 @@ static DEFINE_SPINLOCK(time_lock);
 unsigned long wtimer;
 
 #ifdef CONFIG_PM
-irqreturn_t counter0_irq(int irq, void *dev_id)
+static irqreturn_t counter0_irq(int irq, void *dev_id)
 {
        unsigned long pc0;
        int time_elapsed;
@@ -117,6 +117,13 @@ irqreturn_t counter0_irq(int irq, void *dev_id)
        return IRQ_HANDLED;
 }
 
+struct irqaction counter0_action = {
+       .handler        = counter0_irq,
+       .flags          = IRQF_DISABLED,
+       .name           = "alchemy-toy",
+       .dev_id         = NULL,
+};
+
 /* When we wakeup from sleep, we have to "catch up" on all of the
  * timer ticks we have missed.
  */
@@ -202,18 +209,22 @@ unsigned long cal_r4koff(void)
                while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S);
                au_writel(0, SYS_TOYWRITE);
                while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S);
+       } else
+               no_au1xxx_32khz = 1;
 
-               cpu_speed = (au_readl(SYS_CPUPLL) & 0x0000003f) *
-                       AU1000_SRC_CLK;
-       }
-       else {
-               /* The 32KHz oscillator isn't running, so assume there
-                * isn't one and grab the processor speed from the PLL.
-                * NOTE: some old silicon doesn't allow reading the PLL.
-                */
+       /*
+        * On early Au1000, sys_cpupll was write-only. Since these
+        * silicon versions of Au1000 are not sold by AMD, we don't bend
+        * over backwards trying to determine the frequency.
+        */
+       if (cur_cpu_spec[0]->cpu_pll_wo)
+#ifdef CONFIG_SOC_AU1000_FREQUENCY
+               cpu_speed = CONFIG_SOC_AU1000_FREQUENCY;
+#else
+               cpu_speed = 396000000;
+#endif
+       else
                cpu_speed = (au_readl(SYS_CPUPLL) & 0x0000003f) * AU1000_SRC_CLK;
-               no_au1xxx_32khz = 1;
-       }
        mips_hpt_frequency = cpu_speed;
        // Equation: Baudrate = CPU / (SD * 2 * CLKDIV * 16)
        set_au1x00_uart_baud_base(cpu_speed / (2 * ((int)(au_readl(SYS_POWERCTRL)&0x03) + 2) * 16));
@@ -221,7 +232,7 @@ unsigned long cal_r4koff(void)
        return (cpu_speed / HZ);
 }
 
-void __init plat_timer_setup(struct irqaction *irq)
+void __init plat_time_init(void)
 {
        unsigned int est_freq;
 
@@ -254,17 +265,8 @@ void __init plat_timer_setup(struct irqaction *irq)
         * Check to ensure we really have a 32KHz oscillator before
         * we do this.
         */
-       if (no_au1xxx_32khz) {
-               unsigned int c0_status;
-
+       if (no_au1xxx_32khz)
                printk("WARNING: no 32KHz clock found.\n");
-
-               /* Ensure we get CPO_COUNTER interrupts.
-               */
-               c0_status = read_c0_status();
-               c0_status |= IE_IRQ5;
-               write_c0_status(c0_status);
-       }
        else {
                while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C0S);
                au_writel(0, SYS_TOYWRITE);
@@ -280,7 +282,7 @@ void __init plat_timer_setup(struct irqaction *irq)
                au_writel(last_match20 + MATCH20_INC, SYS_TOYMATCH2);
                au_sync();
                while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_M20);
-               startup_match20_interrupt(counter0_irq);
+               setup_irq(AU1000_TOY_MATCH2_INT, &counter0_action);
 
                /* We can use the real 'wait' instruction.
                */