config ARCH_OMAP2
bool "TI OMAP2"
+ select CPU_V6
+
+config ARCH_OMAP3
+ bool "TI OMAP3"
+ select CPU_V7
endchoice
depends on OMAP_DEBUG_DEVICES
default y if LEDS || LEDS_OMAP_DEBUG
+config OMAP_DEBUG_POWERDOMAIN
+ bool "Emit debug messages from powerdomain layer"
+ depends on ARCH_OMAP2 || ARCH_OMAP3
+ default n
+ help
+ Say Y here if you want to compile in powerdomain layer
+ debugging messages for OMAP2/3. These messages can
+ provide more detail as to why some powerdomain calls
+ may be failing, and will also emit a descriptive message
+ for every powerdomain register write. However, the
+ extra detail costs some memory.
+
+config OMAP_DEBUG_CLOCKDOMAIN
+ bool "Emit debug messages from clockdomain layer"
+ depends on ARCH_OMAP2 || ARCH_OMAP3
+ default n
+ help
+ Say Y here if you want to compile in clockdomain layer
+ debugging messages for OMAP2/3. These messages can
+ provide more detail as to why some clockdomain calls
+ may be failing, and will also emit a descriptive message
+ for every clockdomain register write. However, the
+ extra detail costs some memory.
+
+config OMAP_SMARTREFLEX
+ bool "SmartReflex support"
+ depends on ARCH_OMAP34XX && TWL4030_CORE
+ help
+ Say Y if you want to enable SmartReflex.
+
+ SmartReflex can perform continuous dynamic voltage
+ scaling around the nominal operating point voltage
+ according to silicon characteristics and operating
+ conditions. Enabling SmartReflex reduces power
+ consumption.
+
+ Please note, that by default SmartReflex is only
+ initialized. To enable the automatic voltage
+ compensation for VDD1 and VDD2, user must write 1 to
+ /sys/power/sr_vddX_autocomp, where X is 1 or 2.
+
+config OMAP_SMARTREFLEX_TESTING
+ bool "Smartreflex testing support"
+ depends on OMAP_SMARTREFLEX
+ default n
+ help
+ Say Y if you want to enable SmartReflex testing with SW hardcoded
+ NVALUES intead of E-fuse NVALUES set in factory silicon testing.
+
+ In some devices the E-fuse values have not been set, even though
+ SmartReflex modules are included. Using these hardcoded values set
+ in software, one can test the SmartReflex features without E-fuse.
+
+ WARNING: Enabling this option may cause your device to hang!
+
config OMAP_RESET_CLOCKS
bool "Reset unused clocks during boot"
depends on ARCH_OMAP
probably do not want this option enabled until your
device drivers work properly.
+config OMAP_BOOT_TAG
+ bool "OMAP bootloader information passing"
+ depends on ARCH_OMAP
+ default n
+ help
+ Say Y, if you have a bootloader which passes information
+ about your board and its peripheral configuration.
+
+config OMAP_BOOT_REASON
+ bool "Support for boot reason"
+ depends on OMAP_BOOT_TAG
+ default n
+ help
+ Say Y, if you want to have a procfs entry for reading the boot
+ reason in user-space.
+
+config OMAP_COMPONENT_VERSION
+ bool "Support for component version display"
+ depends on OMAP_BOOT_TAG && PROC_FS
+ default n
+ help
+ Say Y, if you want to have a procfs entry for reading component
+ versions (supplied by the bootloader) in user-space.
+
+config OMAP_GPIO_SWITCH
+ bool "GPIO switch support"
+ default n
+ help
+ Say Y, if you want to have support for reporting of GPIO
+ switches (e.g. cover switches) via sysfs. Your bootloader has
+ to provide information about the switches to the kernel via the
+ ATAG_BOARD mechanism if they're not defined by the board config.
+
config OMAP_MUX
bool "OMAP multiplexing support"
depends on ARCH_OMAP
config OMAP_32K_TIMER
bool "Use 32KHz timer"
- depends on ARCH_OMAP16XX || ARCH_OMAP24XX
+ depends on ARCH_OMAP16XX || ARCH_OMAP24XX || ARCH_OMAP34XX
help
Select this option if you want to enable the OMAP 32KHz timer.
This timer saves power compared to the OMAP_MPU_TIMER, and has
support for no tick during idle. The 32KHz timer provides less
intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is
- currently only available for OMAP16XX and 24XX.
+ currently only available for OMAP16XX, 24XX and 34XX.
endchoice
Kernel internal timer frequency should be a divisor of 32768,
such as 64 or 128.
+config OMAP_TICK_GPTIMER
+ int "GPTIMER used for system tick timer"
+ depends on ARCH_OMAP2 || ARCH_OMAP3
+ range 1 12
+ default 1
+ help
+ Linux uses one of the twelve on-board OMAP GPTIMER blocks to generate
+ system tick interrupts. The twelve GPTIMERs have slightly
+ different powerdomain, source clock, and security properties
+ (mostly documented in the OMAP3 TRMs) that can affect the selection
+ of which GPTIMER to use. The historical default is GPTIMER1.
+ If CONFIG_OMAP_32K_TIMER is selected, Beagle may require GPTIMER12
+ due to hardware sensitivity to glitches on the OMAP 32kHz clock
+ input.
+
config OMAP_DM_TIMER
bool "Use dual-mode timer"
- depends on ARCH_OMAP16XX || ARCH_OMAP24XX
+ depends on ARCH_OMAP16XX || ARCH_OMAP24XX || ARCH_OMAP34XX
help
Select this option if you want to use OMAP Dual-Mode timers.