Merge git://git.infradead.org/mtd-2.6

[linux-2.6-omap-h63xx.git] / arch / arm / mach-pxa / spitz_pm.c

diff --git a/arch/arm/mach-pxa/spitz_pm.c b/arch/arm/mach-pxa/spitz_pm.c
index 8a40505dfd28b8081da8199ff02c31a8d87186d4..072e77cfe5a36ee4002c0b861115e2c0d7c5f8e7 100644 (file)
--- a/arch/arm/mach-pxa/spitz_pm.c
+++ b/arch/arm/mach-pxa/spitz_pm.c
@@ -21,7 +21,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 #include <mach/hardware.h>
-#include <asm/hardware/scoop.h>
 
 #include <mach/sharpsl.h>
 #include <mach/spitz.h>
@@ -48,44 +47,35 @@ static void spitz_charger_init(void)
 
 static void spitz_measure_temp(int on)
 {
-       if (on)
-               set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_ADC_TEMP_ON);
-       else
-               reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_ADC_TEMP_ON);
+       gpio_set_value(SPITZ_GPIO_ADC_TEMP_ON, on);
 }
 
 static void spitz_charge(int on)
 {
        if (on) {
                if (sharpsl_pm.flags & SHARPSL_SUSPENDED) {
-                       set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B);
-                       reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON);
+                       gpio_set_value(SPITZ_GPIO_JK_B, 1);
+                       gpio_set_value(SPITZ_GPIO_CHRG_ON, 0);
                } else {
-                       reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B);
-                       reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON);
+                       gpio_set_value(SPITZ_GPIO_JK_B, 0);
+                       gpio_set_value(SPITZ_GPIO_CHRG_ON, 0);
                }
        } else {
-               reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B);
-               set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON);
+               gpio_set_value(SPITZ_GPIO_JK_B, 0);
+               gpio_set_value(SPITZ_GPIO_CHRG_ON, 1);
        }
 }
 
 static void spitz_discharge(int on)
 {
-       if (on)
-               set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_A);
-       else
-               reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_A);
+       gpio_set_value(SPITZ_GPIO_JK_A, on);
 }
 
 /* HACK - For unknown reasons, accurate voltage readings are only made with a load
    on the power bus which the green led on spitz provides */
 static void spitz_discharge1(int on)
 {
-       if (on)
-               set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_LED_GREEN);
-       else
-               reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_LED_GREEN);
+       gpio_set_value(SPITZ_GPIO_LED_GREEN, on);
 }
 
 static void spitz_presuspend(void)
@@ -208,7 +198,9 @@ struct sharpsl_charger_machinfo spitz_pm_machinfo = {
        .read_devdata     = spitzpm_read_devdata,
        .charger_wakeup   = spitz_charger_wakeup,
        .should_wakeup    = spitz_should_wakeup,
-#ifdef CONFIG_BACKLIGHT_CORGI
+#if defined(CONFIG_LCD_CORGI)
+       .backlight_limit = corgi_lcd_limit_intensity,
+#elif defined(CONFIG_BACKLIGHT_CORGI)
         .backlight_limit  = corgibl_limit_intensity,
 #endif
        .charge_on_volt   = SHARPSL_CHARGE_ON_VOLT,