#include <mach/gpmc.h>
#include <mach/nand.h>
#include <mach/mux.h>
+#include <mach/timer-gp.h>
#include "twl4030-generic-scripts.h"
#include "mmc-twl4030.h"
.setup = beagle_twl_gpio_setup,
};
+static struct platform_device omap3_beagle_lcd_device = {
+ .name = "omap3beagle_lcd",
+ .id = -1,
+};
+
+static struct regulator_consumer_supply beagle_vdac_supply = {
+ .supply = "vdac",
+ .dev = &omap3_beagle_lcd_device.dev,
+};
+
+static struct regulator_consumer_supply beagle_vdvi_supply = {
+ .supply = "vdvi",
+ .dev = &omap3_beagle_lcd_device.dev,
+};
+
/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
static struct regulator_init_data beagle_vmmc1 = {
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &beagle_vdac_supply,
+};
+
+/* VPLL2 for digital video outputs */
+static struct regulator_init_data beagle_vpll2 = {
+ .constraints = {
+ .name = "VDVI",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &beagle_vdvi_supply,
+};
+
+static const struct twl4030_resconfig beagle_resconfig[] = {
+ /* disable regulators that u-boot left enabled; the
+ * devices' drivers should be managing these.
+ */
+ { .resource = RES_VAUX3, }, /* not even connected! */
+ { .resource = RES_VMMC1, },
+ { .resource = RES_VSIM, },
+ { .resource = RES_VPLL2, },
+ { .resource = RES_VDAC, },
+ { .resource = RES_VUSB_1V5, },
+ { .resource = RES_VUSB_1V8, },
+ { .resource = RES_VUSB_3V1, },
+ { 0, },
+};
+
+static struct twl4030_power_data beagle_power_data = {
+ .resource_config = beagle_resconfig,
+ /* REVISIT can't use GENERIC3430_T2SCRIPTS_DATA;
+ * among other things, it makes reboot fail.
+ */
};
static struct twl4030_platform_data beagle_twldata = {
/* platform_data for children goes here */
.usb = &beagle_usb_data,
.gpio = &beagle_gpio_data,
- .power = GENERIC3430_T2SCRIPTS_DATA,
+ .power = &beagle_power_data,
.vmmc1 = &beagle_vmmc1,
.vsim = &beagle_vsim,
.vdac = &beagle_vdac,
+ .vpll2 = &beagle_vpll2,
};
static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
{
omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
omap_init_irq();
+#ifdef CONFIG_OMAP_32K_TIMER
+ omap2_gp_clockevent_set_gptimer(12);
+#endif
omap_gpio_init();
}
-static struct platform_device omap3_beagle_lcd_device = {
- .name = "omap3beagle_lcd",
- .id = -1,
-};
-
static struct omap_lcd_config omap3_beagle_lcd_config __initdata = {
.ctrl_name = "internal",
};