#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/err.h>
+#include <linux/gpio.h>
#include <linux/usb/musb.h>
-#include <asm/arch/gpmc.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/pm.h>
+#include <mach/gpmc.h>
+#include <mach/pm.h>
#define TUSB_ASYNC_CS 1
#define TUSB_SYNC_CS 4
# define BOARD_MODE MUSB_HOST
#endif
+static struct musb_hdrc_eps_bits musb_eps[] = {
+ { "ep1_tx", 5, },
+ { "ep1_rx", 5, },
+ { "ep2_tx", 5, },
+ { "ep2_rx", 5, },
+ { "ep3_tx", 3, },
+ { "ep3_rx", 3, },
+ { "ep4_tx", 3, },
+ { "ep4_rx", 3, },
+ { "ep5_tx", 2, },
+ { "ep5_rx", 2, },
+ { "ep6_tx", 2, },
+ { "ep6_rx", 2, },
+ { "ep7_tx", 2, },
+ { "ep7_rx", 2, },
+ { "ep8_tx", 2, },
+ { "ep8_rx", 2, },
+ { "ep9_tx", 2, },
+ { "ep9_rx", 2, },
+ { "ep10_tx", 2, },
+ { "ep10_rx", 2, },
+ { "ep11_tx", 2, },
+ { "ep11_rx", 2, },
+ { "ep12_tx", 2, },
+ { "ep12_rx", 2, },
+ { "ep13_tx", 2, },
+ { "ep13_rx", 2, },
+ { "ep14_tx", 2, },
+ { "ep14_rx", 2, },
+ { "ep15_tx", 2, },
+ { "ep15_rx", 2, },
+};
+
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 1,
+ .dyn_fifo = 1,
+ .soft_con = 1,
+ .dma = 1,
+ .num_eps = 16,
+ .dma_channels = 7,
+ .ram_bits = 12,
+ .eps_bits = musb_eps,
+};
+
static struct musb_hdrc_platform_data tusb_data = {
.mode = BOARD_MODE,
- .multipoint = 1,
.set_power = tusb_set_power,
.set_clock = tusb_set_clock,
.min_power = 25, /* x2 = 50 mA drawn from VBUS as peripheral */
+ .power = 100, /* Max 100 mA VBUS for host mode */
.clock = "osc_ck",
+ .config = &musb_config,
};
/*
int i, retval = 0;
if (state) {
- omap_set_gpio_dataout(GPIO_TUSB_ENABLE, 1);
+ gpio_set_value(GPIO_TUSB_ENABLE, 1);
msleep(1);
/* Wait until TUSB6010 pulls INT pin down */
i = 100;
- while (i && omap_get_gpio_datain(GPIO_TUSB_INT)) {
+ while (i && gpio_get_value(GPIO_TUSB_INT)) {
msleep(1);
i--;
}
retval = -ENODEV;
}
} else {
- omap_set_gpio_dataout(GPIO_TUSB_ENABLE, 0);
+ gpio_set_value(GPIO_TUSB_ENABLE, 0);
msleep(10);
}
if (osc_ck_on > 0)
return -ENODEV;
- omap2_block_sleep();
+ //omap2_block_sleep();
clk_enable(osc_ck);
osc_ck_on = 1;
} else {
clk_disable(osc_ck);
osc_ck_on = 0;
- omap2_allow_sleep();
+ //omap2_allow_sleep();
}
return 0;
static char announce[] __initdata = KERN_INFO "TUSB 6010\n";
/* PM companion chip power control pin */
- ret = omap_request_gpio(GPIO_TUSB_ENABLE);
+ ret = gpio_request(GPIO_TUSB_ENABLE, "TUSB6010 enable");
if (ret != 0) {
printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
GPIO_TUSB_ENABLE);
return;
}
- omap_set_gpio_direction(GPIO_TUSB_ENABLE, 0);
+ gpio_direction_output(GPIO_TUSB_ENABLE, 0);
tusb_set_power(0);
return;
err:
- omap_free_gpio(GPIO_TUSB_ENABLE);
+ gpio_free(GPIO_TUSB_ENABLE);
}