#include <mach/control.h>
#include <mach/gpio.h>
-#include <mach/gpioexpander.h>
#include <mach/mux.h>
#include <mach/usb.h>
-#include <mach/irda.h>
#include <mach/board.h>
#include <mach/common.h>
#include <mach/keypad.h>
#define H4_FLASH_CS 0
#define H4_SMC91X_CS 1
+#define H4_ETHR_GPIO_IRQ 92
+
static unsigned int row_gpios[6] = { 88, 89, 124, 11, 6, 96 };
static unsigned int col_gpios[7] = { 90, 91, 100, 36, 12, 97, 98 };
.resource = &h4_flash_resource,
};
-/* Select between the IrDA and aGPS module
- */
-static int h4_select_irda(struct device *dev, int state)
-{
- unsigned char expa;
- int err = 0;
-
- if ((err = read_gpio_expa(&expa, 0x21))) {
- printk(KERN_ERR "Error reading from I/O expander\n");
- return err;
- }
-
- /* 'P6' enable/disable IRDA_TX and IRDA_RX */
- if (state & IR_SEL) { /* IrDa */
- if ((err = write_gpio_expa(expa | 0x01, 0x21))) {
- printk(KERN_ERR "Error writing to I/O expander\n");
- return err;
- }
- } else {
- if ((err = write_gpio_expa(expa & ~0x01, 0x21))) {
- printk(KERN_ERR "Error writing to I/O expander\n");
- return err;
- }
- }
- return err;
-}
-
-static void set_trans_mode(struct work_struct *work)
-{
- struct omap_irda_config *irda_config =
- container_of(work, struct omap_irda_config, gpio_expa.work);
- int mode = irda_config->mode;
- unsigned char expa;
- int err = 0;
-
- if ((err = read_gpio_expa(&expa, 0x20)) != 0) {
- printk(KERN_ERR "Error reading from I/O expander\n");
- }
-
- expa &= ~0x01;
-
- if (!(mode & IR_SIRMODE)) { /* MIR/FIR */
- expa |= 0x01;
- }
-
- if ((err = write_gpio_expa(expa, 0x20)) != 0) {
- printk(KERN_ERR "Error writing to I/O expander\n");
- }
-}
-
-static int h4_transceiver_mode(struct device *dev, int mode)
-{
- struct omap_irda_config *irda_config = dev->platform_data;
-
- irda_config->mode = mode;
- cancel_delayed_work(&irda_config->gpio_expa);
- PREPARE_DELAYED_WORK(&irda_config->gpio_expa, set_trans_mode);
- schedule_delayed_work(&irda_config->gpio_expa, 0);
-
- return 0;
-}
-
-static struct omap_irda_config h4_irda_data = {
- .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
- .transceiver_mode = h4_transceiver_mode,
- .select_irda = h4_select_irda,
- .rx_channel = OMAP24XX_DMA_UART3_RX,
- .tx_channel = OMAP24XX_DMA_UART3_TX,
- .dest_start = OMAP_UART3_BASE,
- .src_start = OMAP_UART3_BASE,
- .tx_trigger = OMAP24XX_DMA_UART3_TX,
- .rx_trigger = OMAP24XX_DMA_UART3_RX,
-};
-
-static struct resource h4_irda_resources[] = {
- [0] = {
- .start = INT_24XX_UART3_IRQ,
- .end = INT_24XX_UART3_IRQ,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device h4_irda_device = {
- .name = "omapirda",
- .id = -1,
- .dev = {
- .platform_data = &h4_irda_data,
- },
- .num_resources = 1,
- .resource = h4_irda_resources,
-};
-
static struct omap_kp_platform_data h4_kp_data = {
.rows = 6,
.cols = 7,
static struct platform_device *h4_devices[] __initdata = {
&h4_flash_device,
- &h4_irda_device,
&h4_kp_device,
&h4_lcd_device,
};
udelay(100);
omap_cfg_reg(M15_24XX_GPIO92);
- if (debug_card_init(cs_mem_base, OMAP24XX_ETHR_GPIO_IRQ) < 0)
+ if (debug_card_init(cs_mem_base, H4_ETHR_GPIO_IRQ) < 0)
gpmc_cs_free(eth_cs);
out:
static void __init omap_h4_init_irq(void)
{
- omap2_init_common_hw();
+ omap2_init_common_hw(NULL);
omap_init_irq();
omap_gpio_init();
h4_init_flash();
.ctrl_name = "internal",
};
+static struct omap_usb_config h4_usb_config __initdata = {
+#ifdef CONFIG_MACH_OMAP2_H4_USB1
+ /* NOTE: usb1 could also be used with 3 wire signaling */
+ .pins[1] = 4,
+#endif
+
+#ifdef CONFIG_MACH_OMAP_H4_OTG
+ /* S1.10 ON -- USB OTG port
+ * usb0 switched to Mini-AB port and isp1301 transceiver;
+ * S2.POS3 = OFF, S2.POS4 = ON ... to allow battery charging
+ */
+ .otg = 1,
+ .pins[0] = 4,
+#ifdef CONFIG_USB_GADGET_OMAP
+ /* use OTG cable, or standard A-to-MiniB */
+ .hmc_mode = 0x14, /* 0:dev/otg 1:host 2:disable */
+#elif defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+ /* use OTG cable, or NONSTANDARD (B-to-MiniB) */
+ .hmc_mode = 0x11, /* 0:host 1:host 2:disable */
+#endif /* XX */
+
+#else
+ /* S1.10 OFF -- usb "download port"
+ * usb0 switched to Mini-B port and isp1105 transceiver;
+ * S2.POS3 = ON, S2.POS4 = OFF ... to enable battery charging
+ */
+ .register_dev = 1,
+ .pins[0] = 3,
+/* .hmc_mode = 0x14,*/ /* 0:dev 1:host 2:disable */
+ .hmc_mode = 0x00, /* 0:dev|otg 1:disable 2:disable */
+#endif
+};
+
static struct omap_board_config_kernel h4_config[] = {
{ OMAP_TAG_UART, &h4_uart_config },
{ OMAP_TAG_LCD, &h4_lcd_config },
platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
omap_board_config = h4_config;
omap_board_config_size = ARRAY_SIZE(h4_config);
+ omap_usb_init(&h4_usb_config);
omap_serial_init();
}
projects / linux-2.6-omap-h63xx.git / blobdiff