#include <linux/delay.h>
#include <linux/workqueue.h>
#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
#include <linux/input.h>
#include <linux/err.h>
#include <linux/clk.h>
#define H4_FLASH_CS 0
#define H4_SMC91X_CS 1
+#define H4_ETHR_GPIO_IRQ 92
+
static unsigned int row_gpios[6] = { 88, 89, 124, 11, 6, 96 };
static unsigned int col_gpios[7] = { 90, 91, 100, 36, 12, 97, 98 };
udelay(100);
omap_cfg_reg(M15_24XX_GPIO92);
- if (debug_card_init(cs_mem_base, OMAP24XX_ETHR_GPIO_IRQ) < 0)
+ if (debug_card_init(cs_mem_base, H4_ETHR_GPIO_IRQ) < 0)
gpmc_cs_free(eth_cs);
out:
static void __init omap_h4_init_irq(void)
{
- omap2_init_common_hw();
+ omap2_init_common_hw(NULL);
omap_init_irq();
omap_gpio_init();
h4_init_flash();
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
-static struct omap_mmc_config h4_mmc_config __initdata = {
- .mmc [0] = {
- .enabled = 1,
- .wire4 = 1,
- .wp_pin = -1,
- .power_pin = -1,
- .switch_pin = -1,
- },
-};
-
static struct omap_lcd_config h4_lcd_config __initdata = {
.ctrl_name = "internal",
};
+static struct omap_usb_config h4_usb_config __initdata = {
+#ifdef CONFIG_MACH_OMAP2_H4_USB1
+ /* NOTE: usb1 could also be used with 3 wire signaling */
+ .pins[1] = 4,
+#endif
+
+#ifdef CONFIG_MACH_OMAP_H4_OTG
+ /* S1.10 ON -- USB OTG port
+ * usb0 switched to Mini-AB port and isp1301 transceiver;
+ * S2.POS3 = OFF, S2.POS4 = ON ... to allow battery charging
+ */
+ .otg = 1,
+ .pins[0] = 4,
+#ifdef CONFIG_USB_GADGET_OMAP
+ /* use OTG cable, or standard A-to-MiniB */
+ .hmc_mode = 0x14, /* 0:dev/otg 1:host 2:disable */
+#elif defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+ /* use OTG cable, or NONSTANDARD (B-to-MiniB) */
+ .hmc_mode = 0x11, /* 0:host 1:host 2:disable */
+#endif /* XX */
+
+#else
+ /* S1.10 OFF -- usb "download port"
+ * usb0 switched to Mini-B port and isp1105 transceiver;
+ * S2.POS3 = ON, S2.POS4 = OFF ... to enable battery charging
+ */
+ .register_dev = 1,
+ .pins[0] = 3,
+/* .hmc_mode = 0x14,*/ /* 0:dev 1:host 2:disable */
+ .hmc_mode = 0x00, /* 0:dev|otg 1:disable 2:disable */
+#endif
+};
+
static struct omap_board_config_kernel h4_config[] = {
{ OMAP_TAG_UART, &h4_uart_config },
- { OMAP_TAG_MMC, &h4_mmc_config },
{ OMAP_TAG_LCD, &h4_lcd_config },
};
+static struct at24_platform_data m24c01 = {
+ .byte_len = SZ_1K / 8,
+ .page_size = 16,
+};
+
static struct i2c_board_info __initdata h4_i2c_board_info[] = {
{
I2C_BOARD_INFO("isp1301_omap", 0x2d),
.irq = OMAP_GPIO_IRQ(125),
},
+ { /* EEPROM on mainboard */
+ I2C_BOARD_INFO("24c01", 0x52),
+ .platform_data = &m24c01,
+ },
+ { /* EEPROM on cpu card */
+ I2C_BOARD_INFO("24c01", 0x57),
+ .platform_data = &m24c01,
+ },
};
static void __init omap_h4_init(void)
platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
omap_board_config = h4_config;
omap_board_config_size = ARRAY_SIZE(h4_config);
+ omap_usb_init(&h4_usb_config);
omap_serial_init();
}