#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/delay.h>
+#include <linux/workqueue.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/flash.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/gpioexpander.h>
#include <asm/arch/mux.h>
#include <asm/arch/usb.h>
+#include <asm/arch/irda.h>
#include <asm/arch/board.h>
#include <asm/arch/common.h>
#include "prcm-regs.h"
.resource = h4_smc91x_resources,
};
+/* Select between the IrDA and aGPS module
+ */
+static int h4_select_irda(struct device *dev, int state)
+{
+ unsigned char expa;
+ int err = 0;
+
+ if ((err = read_gpio_expa(&expa, 0x21))) {
+ printk(KERN_ERR "Error reading from I/O expander\n");
+ return err;
+ }
+
+ /* 'P6' enable/disable IRDA_TX and IRDA_RX */
+ if (state & IR_SEL) { /* IrDa */
+ if ((err = write_gpio_expa(expa | 0x01, 0x21))) {
+ printk(KERN_ERR "Error writing to I/O expander\n");
+ return err;
+ }
+ } else {
+ if ((err = write_gpio_expa(expa & ~0x01, 0x21))) {
+ printk(KERN_ERR "Error writing to I/O expander\n");
+ return err;
+ }
+ }
+ return err;
+}
+
+static void set_trans_mode(void *data)
+{
+ int *mode = data;
+ unsigned char expa;
+ int err = 0;
+
+ if ((err = read_gpio_expa(&expa, 0x20)) != 0) {
+ printk(KERN_ERR "Error reading from I/O expander\n");
+ }
+
+ expa &= ~0x01;
+
+ if (!(*mode & IR_SIRMODE)) { /* MIR/FIR */
+ expa |= 0x01;
+ }
+
+ if ((err = write_gpio_expa(expa, 0x20)) != 0) {
+ printk(KERN_ERR "Error writing to I/O expander\n");
+ }
+}
+
+static int h4_transceiver_mode(struct device *dev, int mode)
+{
+ struct omap_irda_config *irda_config = dev->platform_data;
+
+ cancel_delayed_work(&irda_config->gpio_expa);
+ PREPARE_WORK(&irda_config->gpio_expa, set_trans_mode, &mode);
+ schedule_work(&irda_config->gpio_expa);
+
+ return 0;
+}
+
+static struct omap_irda_config h4_irda_data = {
+ .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
+ .transceiver_mode = h4_transceiver_mode,
+ .select_irda = h4_select_irda,
+};
+
+static struct resource h4_irda_resources[] = {
+ [0] = {
+ .start = INT_24XX_UART3_IRQ,
+ .end = INT_24XX_UART3_IRQ,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device h4_irda_device = {
+ .name = "omapirda",
+ .id = -1,
+ .dev = {
+ .platform_data = &h4_irda_data,
+ },
+ .num_resources = 1,
+ .resource = h4_irda_resources,
+};
+
static struct platform_device *h4_devices[] __initdata = {
&h4_smc91x_device,
&h4_flash_device,
+ &h4_irda_device,
};
static inline void __init h4_init_smc91x(void)
* You have to mux them off in device drivers later on
* if not needed.
*/
+#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
+ omap_cfg_reg(K15_24XX_UART3_TX);
+ omap_cfg_reg(K14_24XX_UART3_RX);
+#endif
platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
omap_board_config = h4_config;
omap_board_config_size = ARRAY_SIZE(h4_config);