#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/i2c/twl4030.h>
+#include <linux/regulator/machine.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <mach/gpio.h>
#include <mach/mux.h>
#include <mach/board.h>
-#include <mach/usb-musb.h>
-#include <mach/usb-ehci.h>
-#include <mach/mmc.h>
+#include <mach/usb.h>
#include <mach/common.h>
-#include <mach/keypad.h>
#include <mach/dma.h>
#include <mach/gpmc.h>
static struct resource sdp3430_smc91x_resources[] = {
[0] = {
- .start = OMAP34XX_ETHR_START,
- .end = OMAP34XX_ETHR_START + SZ_4K,
.flags = IORESOURCE_MEM,
},
[1] = {
.keymap = sdp3430_keymap,
.keymapsize = ARRAY_SIZE(sdp3430_keymap),
.rep = 1,
- .irq = TWL4030_MODIRQ_KEYPAD,
};
static int ts_gpio;
*/
static void ads7846_dev_init(void)
{
- if (omap_request_gpio(ts_gpio) < 0) {
+ if (gpio_request(ts_gpio, "ADS7846 pendown") < 0) {
printk(KERN_ERR "can't get ads746 pen down GPIO\n");
return;
}
- omap_set_gpio_direction(ts_gpio, 1);
+ gpio_direction_input(ts_gpio);
omap_set_gpio_debounce(ts_gpio, 1);
omap_set_gpio_debounce_time(ts_gpio, 0xa);
static int ads7846_get_pendown_state(void)
{
- return !omap_get_gpio_datain(ts_gpio);
+ return !gpio_get_value(ts_gpio);
}
/*
return;
}
- sdp3430_smc91x_resources[0].start = cs_mem_base + 0x0;
- sdp3430_smc91x_resources[0].end = cs_mem_base + 0xf;
+ sdp3430_smc91x_resources[0].start = cs_mem_base + 0x300;
+ sdp3430_smc91x_resources[0].end = cs_mem_base + 0x30f;
udelay(100);
if (omap_rev() > OMAP3430_REV_ES1_0)
else
eth_gpio = OMAP34XX_ETHR_GPIO_IRQ_SDPV1;
- sdp3430_smc91x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio);
+ sdp3430_smc91x_resources[1].start = gpio_to_irq(eth_gpio);
- if (omap_request_gpio(eth_gpio) < 0) {
+ if (gpio_request(eth_gpio, "SMC91x irq") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
eth_gpio);
return;
}
- omap_set_gpio_direction(eth_gpio, 1);
+ gpio_direction_input(eth_gpio);
}
static void __init omap_3430sdp_init_irq(void)
.tblsize = ARRAY_SIZE(sdp3430_batt_table),
};
+static struct twl4030_hsmmc_info mmc[] = {
+ {
+ .mmc = 1,
+ /* 8 bits (default) requires S6.3 == ON,
+ * so the SIM card isn't used; else 4 bits.
+ */
+ .wires = 8,
+ .gpio_wp = 4,
+ },
+ {
+ .mmc = 2,
+ .wires = 8,
+ .gpio_wp = 7,
+ },
+ {} /* Terminator */
+};
+
+static struct regulator_consumer_supply sdp3430_vmmc1_supply = {
+ .supply = "vmmc",
+};
+
+static struct regulator_consumer_supply sdp3430_vsim_supply = {
+ .supply = "vmmc_dat4..7",
+};
+
+static struct regulator_consumer_supply sdp3430_vmmc2_supply = {
+ .supply = "vmmc",
+};
+
+static int sdp3430_twl_gpio_setup(struct device *dev,
+ unsigned gpio, unsigned ngpio)
+{
+ /* gpio + 0 is "mmc0_cd" (input/IRQ),
+ * gpio + 1 is "mmc1_cd" (input/IRQ)
+ */
+ mmc[0].gpio_cd = gpio + 0;
+ mmc[1].gpio_cd = gpio + 1;
+ twl4030_mmc_init(mmc);
+
+ /* link regulators to MMC adapters ... we "know" the
+ * regulators will be set up only *after* we return.
+ */
+ sdp3430_vmmc1_supply.dev = mmc[0].dev;
+ sdp3430_vsim_supply.dev = mmc[0].dev;
+ sdp3430_vmmc2_supply.dev = mmc[1].dev;
+
+ /* gpio + 7 is "sub_lcd_en_bkl" (output/PWM1) */
+ gpio_request(gpio + 7, "sub_lcd_en_bkl");
+ gpio_direction_output(gpio + 7, 0);
+
+ /* gpio + 15 is "sub_lcd_nRST" (output) */
+ gpio_request(gpio + 15, "sub_lcd_nRST");
+ gpio_direction_output(gpio + 15, 0);
+
+ return 0;
+}
+
static struct twl4030_gpio_platform_data sdp3430_gpio_data = {
.gpio_base = OMAP_MAX_GPIO_LINES,
.irq_base = TWL4030_GPIO_IRQ_BASE,
.irq_end = TWL4030_GPIO_IRQ_END,
+ .pulldowns = BIT(2) | BIT(6) | BIT(8) | BIT(13)
+ | BIT(16) | BIT(17),
+ .setup = sdp3430_twl_gpio_setup,
};
static struct twl4030_usb_data sdp3430_usb_data = {
.size = ARRAY_SIZE(twl4030_scripts),
};
+/*
+ * Apply all the fixed voltages since most versions of U-Boot
+ * don't bother with that initialization.
+ */
+
+/* VAUX1 for mainboard (irda and sub-lcd) */
+static struct regulator_init_data sdp3430_vaux1 = {
+ .constraints = {
+ .min_uV = 2800000,
+ .max_uV = 2800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+};
+
+/* VAUX2 for camera module */
+static struct regulator_init_data sdp3430_vaux2 = {
+ .constraints = {
+ .min_uV = 2800000,
+ .max_uV = 2800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+};
+
+/* VAUX3 for LCD board */
+static struct regulator_init_data sdp3430_vaux3 = {
+ .constraints = {
+ .min_uV = 2800000,
+ .max_uV = 2800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+};
+
+/* VAUX4 for OMAP VDD_CSI2 (camera) */
+static struct regulator_init_data sdp3430_vaux4 = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+};
+
+/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
+static struct regulator_init_data sdp3430_vmmc1 = {
+ .constraints = {
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &sdp3430_vmmc1_supply,
+};
+
+/* VMMC2 for MMC2 card */
+static struct regulator_init_data sdp3430_vmmc2 = {
+ .constraints = {
+ .min_uV = 1850000,
+ .max_uV = 1850000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &sdp3430_vmmc2_supply,
+};
+
+/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */
+static struct regulator_init_data sdp3430_vsim = {
+ .constraints = {
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &sdp3430_vsim_supply,
+};
+
+/* VDAC for DSS driving S-Video */
+static struct regulator_init_data sdp3430_vdac = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+};
+
static struct twl4030_platform_data sdp3430_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
.keypad = &sdp3430_kp_data,
.power = &sdp3430_t2scripts_data,
.usb = &sdp3430_usb_data,
+
+ .vaux1 = &sdp3430_vaux1,
+ .vaux2 = &sdp3430_vaux2,
+ .vaux3 = &sdp3430_vaux3,
+ .vaux4 = &sdp3430_vaux4,
+ .vmmc1 = &sdp3430_vmmc1,
+ .vmmc2 = &sdp3430_vmmc2,
+ .vsim = &sdp3430_vsim,
+ .vdac = &sdp3430_vdac,
};
static struct i2c_board_info __initdata sdp3430_i2c_boardinfo[] = {
static int __init omap3430_i2c_init(void)
{
+ /* i2c1 for PMIC only */
omap_register_i2c_bus(1, 2600, sdp3430_i2c_boardinfo,
ARRAY_SIZE(sdp3430_i2c_boardinfo));
+ /* i2c2 on camera connector (for sensor control) and optional isp1301 */
omap_register_i2c_bus(2, 400, NULL, 0);
+ /* i2c3 on display connector (for DVI, tfp410) */
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
-static struct twl4030_hsmmc_info mmc[] __initdata = {
- {
- .mmc = 1,
- .wires = 8,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- },
- {
- .mmc = 2,
- .wires = 8,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- },
- {} /* Terminator */
-};
-
extern void __init sdp3430_flash_init(void);
static void __init omap_3430sdp_init(void)
ts_gpio = OMAP34XX_TS_GPIO_IRQ_SDPV2;
else
ts_gpio = OMAP34XX_TS_GPIO_IRQ_SDPV1;
- sdp3430_spi_board_info[0].irq = OMAP_GPIO_IRQ(ts_gpio);
+ sdp3430_spi_board_info[0].irq = gpio_to_irq(ts_gpio);
spi_register_board_info(sdp3430_spi_board_info,
ARRAY_SIZE(sdp3430_spi_board_info));
ads7846_dev_init();
omap_serial_init();
usb_musb_init();
usb_ehci_init();
- hsmmc_init(mmc);
}
static void __init omap_3430sdp_map_io(void)
projects / linux-2.6-omap-h63xx.git / blobdiff