depends on ARCH_OMAP24XX
select OMAP_DM_TIMER
select ARCH_OMAP_OTG
- select CPU_V6
config ARCH_OMAP2430
bool "OMAP2430 support"
depends on ARCH_OMAP24XX
- select ARCH_OMAP_OTG
- select CPU_V6
config ARCH_OMAP34XX
bool "OMAP34xx Based System"
bool "OMAP3430 support"
depends on ARCH_OMAP3 && ARCH_OMAP34XX
select ARCH_OMAP_OTG
- select CPU_V7
comment "OMAP Board Type"
depends on ARCH_OMAP2 || ARCH_OMAP3
bool "Generic OMAP board"
depends on ARCH_OMAP2 && ARCH_OMAP24XX
-config MACH_NOKIA_N800
- bool "Nokia N800"
- depends on ARCH_OMAP2420
- select VIDEO_TCM825X if VIDEO_OMAP2 && VIDEO_HELPER_CHIPS_AUTO
- select CBUS if VIDEO_TCM825X
- select CBUS_RETU if VIDEO_TCM825X
- select MENELAUS if VIDEO_TCM825X
- select OMAP_GPIO_SWITCH
-
-config MACH_NOKIA_N810
- bool "Nokia N810"
- depends on MACH_NOKIA_N800
-
-config MACH_NOKIA_N810_WIMAX
- bool "Nokia N810 WiMAX"
- depends on MACH_NOKIA_N800
- select MACH_NOKIA_N810
-
-config MACH_NOKIA_RX51
- bool "Nokia RX-51 board"
- depends on ARCH_OMAP3 && ARCH_OMAP34XX
-
-config MACH_OMAP2_TUSB6010
- bool
- depends on ARCH_OMAP2 && ARCH_OMAP2420
- default y if MACH_NOKIA_N800
-
config MACH_OMAP_H4
bool "OMAP 2420 H4 board"
- depends on ARCH_OMAP2 && ARCH_OMAP2420
+ depends on ARCH_OMAP2 && ARCH_OMAP24XX
select OMAP_DEBUG_DEVICES
-config MACH_OMAP_H4_TUSB
- bool "TUSB 6010 EVM board"
- depends on MACH_OMAP_H4
- select MACH_OMAP2_TUSB6010
- help
- Set this if you've got a TUSB6010 high speed USB board.
- You may need to consult the schematics for your revisions
- of the Menelaus and TUSB boards, and make changes to be
- sure this is set up properly for your board stack.
-
- Be sure to select OTG mode operation, not host-only or
- peripheral-only.
-
-config MACH_OMAP_H4_OTG
- bool "Use USB OTG connector, not device connector (S1.10)"
- depends on MACH_OMAP_H4
- help
- Set this if you've set S1.10 (on the mainboard) to use the
- Mini-AB (OTG) connector and OTG transceiver with the USB0
- port, instead of the Mini-B ("download") connector with its
- non-OTG transceiver.
-
- Note that the "download" connector can be used to bootstrap
- the system from the OMAP mask ROM. Also, since this is a
- development platform, you can also force the OTG port into
- a non-OTG operational mode.
-
-config MACH_OMAP2_H4_USB1
- bool "Use USB1 port, not UART2 (S3.3)"
- depends on MACH_OMAP_H4
- help
- Set this if you've set SW3.3 (on the CPU card) so that the
- expansion connectors receive USB1 signals instead of UART2.
-
config MACH_OMAP_APOLLON
bool "OMAP 2420 Apollon board"
- depends on ARCH_OMAP2 && ARCH_OMAP2420
+ depends on ARCH_OMAP2 && ARCH_OMAP24XX
config MACH_OMAP_2430SDP
bool "OMAP 2430 SDP board"
- depends on ARCH_OMAP2 && ARCH_OMAP2430
-
-config MACH_OMAP_LDP
- bool "OMAP3 LDP board"
- depends on ARCH_OMAP3 && ARCH_OMAP34XX
-
-config MACH_OMAP2EVM
- bool "OMAP 2530 EVM board"
depends on ARCH_OMAP2 && ARCH_OMAP24XX
-config MACH_OMAP_3430SDP
- bool "OMAP 3430 SDP board"
- depends on ARCH_OMAP3 && ARCH_OMAP34XX
-
-config MACH_OMAP3EVM
- bool "OMAP 3530 EVM board"
- depends on ARCH_OMAP3 && ARCH_OMAP34XX
-
config MACH_OMAP3_BEAGLE
bool "OMAP3 BEAGLE board"
depends on ARCH_OMAP3 && ARCH_OMAP34XX
+config MACH_OMAP_LDP
+ bool "OMAP3 LDP board"
+ depends on ARCH_OMAP3 && ARCH_OMAP34XX
+
config MACH_OVERO
bool "Gumstix Overo board"
depends on ARCH_OMAP3 && ARCH_OMAP34XX