REMOVE OMAP LEGACY CODE: Reset mach-omap1/board-*.c files to mainline

[linux-2.6-omap-h63xx.git] / arch / arm / mach-omap1 / board-palmte.c

diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c
index b58043644a6f55681ba5c66cb1d3a47f03687116..99f2b43f2541bff7b4b898786ba48a2b98bebb4c 100644 (file)
--- a/arch/arm/mach-omap1/board-palmte.c
+++ b/arch/arm/mach-omap1/board-palmte.c
@@ -42,8 +42,6 @@
 #include <mach/irda.h>
 #include <mach/keypad.h>
 #include <mach/common.h>
-#include <mach/mcbsp.h>
-#include <mach/omap-alsa.h>
 
 static void __init omap_palmte_init_irq(void)
 {
@@ -195,15 +193,6 @@ static struct omap_usb_config palmte_usb_config __initdata = {
        .pins[0]        = 2,
 };
 
-static struct omap_mmc_config palmte_mmc_config __initdata = {
-       .mmc[0]         = {
-               .enabled        = 1,
-               .wp_pin         = PALMTE_MMC_WP_GPIO,
-               .power_pin      = PALMTE_MMC_POWER_GPIO,
-               .switch_pin     = PALMTE_MMC_SWITCH_GPIO,
-       },
-};
-
 static struct omap_lcd_config palmte_lcd_config __initdata = {
        .ctrl_name      = "internal",
 };
@@ -212,24 +201,6 @@ static struct omap_uart_config palmte_uart_config __initdata = {
        .enabled_uarts = (1 << 0) | (1 << 1) | (0 << 2),
 };
 
-static struct omap_mcbsp_reg_cfg palmte_mcbsp1_regs = {
-       .spcr2  = FRST | GRST | XRST | XINTM(3),
-       .xcr2   = XDATDLY(1) | XFIG,
-       .xcr1   = XWDLEN1(OMAP_MCBSP_WORD_32),
-       .pcr0   = SCLKME | FSXP | CLKXP,
-};
-
-static struct omap_alsa_codec_config palmte_alsa_config = {
-       .name                   = "TSC2102 audio",
-       .mcbsp_regs_alsa        = &palmte_mcbsp1_regs,
-       .codec_configure_dev    = NULL, /* tsc2102_configure, */
-       .codec_set_samplerate   = NULL, /* tsc2102_set_samplerate, */
-       .codec_clock_setup      = NULL, /* tsc2102_clock_setup, */
-       .codec_clock_on         = NULL, /* tsc2102_clock_on, */
-       .codec_clock_off        = NULL, /* tsc2102_clock_off, */
-       .get_default_samplerate = NULL, /* tsc2102_get_default_samplerate, */
-};
-
 #ifdef CONFIG_APM
 /*
  * Values measured in 10 minute intervals averaged over 10 samples.
@@ -255,7 +226,7 @@ static void palmte_get_power_status(struct apm_power_info *info, int *battery)
 {
        int charging, batt, hi, lo, mid;
 
-       charging = !omap_get_gpio_datain(PALMTE_DC_GPIO);
+       charging = !gpio_get_value(PALMTE_DC_GPIO);
        batt = battery[0];
        if (charging)
                batt -= 60;
@@ -316,7 +287,6 @@ static void palmte_get_power_status(struct apm_power_info *info, int *battery)
 
 static struct omap_board_config_kernel palmte_config[] __initdata = {
        { OMAP_TAG_USB,         &palmte_usb_config },
-       { OMAP_TAG_MMC,         &palmte_mmc_config },
        { OMAP_TAG_LCD,         &palmte_lcd_config },
        { OMAP_TAG_UART,        &palmte_uart_config },
 };
@@ -335,11 +305,11 @@ static void palmte_headphones_detect(void *data, int state)
 {
        if (state) {
                /* Headphones connected, disable speaker */
-               omap_set_gpio_dataout(PALMTE_SPEAKER_GPIO, 0);
+               gpio_set_value(PALMTE_SPEAKER_GPIO, 0);
                printk(KERN_INFO "PM: speaker off\n");
        } else {
                /* Headphones unplugged, re-enable speaker */
-               omap_set_gpio_dataout(PALMTE_SPEAKER_GPIO, 1);
+               gpio_set_value(PALMTE_SPEAKER_GPIO, 1);
                printk(KERN_INFO "PM: speaker on\n");
        }
 }
@@ -347,18 +317,18 @@ static void palmte_headphones_detect(void *data, int state)
 static void __init palmte_misc_gpio_setup(void)
 {
        /* Set TSC2102 PINTDAV pin as input (used by TSC2102 driver) */
-       if (omap_request_gpio(PALMTE_PINTDAV_GPIO)) {
+       if (gpio_request(PALMTE_PINTDAV_GPIO, "TSC2102 PINTDAV") < 0) {
                printk(KERN_ERR "Could not reserve PINTDAV GPIO!\n");
                return;
        }
-       omap_set_gpio_direction(PALMTE_PINTDAV_GPIO, 1);
+       gpio_direction_input(PALMTE_PINTDAV_GPIO);
 
        /* Set USB-or-DC-IN pin as input (unused) */
-       if (omap_request_gpio(PALMTE_USB_OR_DC_GPIO)) {
+       if (gpio_request(PALMTE_USB_OR_DC_GPIO, "USB/DC-IN") < 0) {
                printk(KERN_ERR "Could not reserve cable signal GPIO!\n");
                return;
        }
-       omap_set_gpio_direction(PALMTE_USB_OR_DC_GPIO, 1);
+       gpio_direction_input(PALMTE_USB_OR_DC_GPIO);
 }
 
 static void __init omap_palmte_init(void)