#include <linux/mtd/partitions.h>
#include <linux/input.h>
#include <linux/i2c/tps65010.h>
+#include <linux/clk.h>
+#include <linux/i2c.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/tsc210x.h>
#include <asm/setup.h>
#include <asm/page.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
+#include <media/v4l2-int-device.h>
+
+#include <asm/arch/gpio.h>
+#include <asm/arch/gpio-switch.h>
#include <asm/arch/gpioexpander.h>
#include <asm/arch/irqs.h>
#include <asm/arch/mux.h>
#include <asm/arch/mcbsp.h>
#include <asm/arch/omap-alsa.h>
+#include <../drivers/media/video/ov9640.h>
+
+#define H3_TS_GPIO 48
+
static int h3_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_RIGHT),
.id = -1,
};
+static struct tsc210x_config tsc_platform_data = {
+ .use_internal = 1,
+ .monitor = TSC_VBAT | TSC_TEMP,
+ .mclk = "mclk",
+};
+
+static struct spi_board_info h3_spi_board_info[] __initdata = {
+ [0] = {
+ .modalias = "tsc2101",
+ .bus_num = 2,
+ .chip_select = 0,
+ .irq = OMAP_GPIO_IRQ(H3_TS_GPIO),
+ .max_speed_hz = 16000000,
+ .platform_data = &tsc_platform_data,
+ },
+};
+
static struct omap_mcbsp_reg_cfg mcbsp_regs = {
.spcr2 = FREE | FRST | GRST | XRST | XINTM(3),
.spcr1 = RINTM(3) | RRST,
return omap_get_gpio_datain(H3_NAND_RB_GPIO_PIN);
}
+#if defined(CONFIG_VIDEO_OV9640) || defined(CONFIG_VIDEO_OV9640_MODULE)
+/*
+ * Common OV9640 register initialization for all image sizes, pixel formats,
+ * and frame rates
+ */
+const static struct ov9640_reg ov9640_common[] = {
+
+ { 0x12, 0x80 }, { 0x11, 0x80 }, { 0x13, 0x88 }, /* COM7, CLKRC, COM8 */
+ { 0x01, 0x58 }, { 0x02, 0x24 }, { 0x04, 0x00 }, /* BLUE, RED, COM1 */
+ { 0x0E, 0x81 }, { 0x0F, 0x4F }, { 0x14, 0xcA }, /* COM5, COM6, COM9 */
+ { 0x16, 0x02 }, { 0x1B, 0x01 }, { 0x24, 0x70 }, /* ?, PSHFT, AEW */
+ { 0x25, 0x68 }, { 0x26, 0xD3 }, { 0x27, 0x90 }, /* AEB, VPT, BBIAS */
+ { 0x2A, 0x00 }, { 0x2B, 0x00 }, { 0x32, 0x24 }, /* EXHCH, EXHCL, HREF */
+ { 0x33, 0x02 }, { 0x37, 0x02 }, { 0x38, 0x13 }, /* CHLF, ADC, ACOM */
+ { 0x39, 0xF0 }, { 0x3A, 0x00 }, { 0x3B, 0x01 }, /* OFON, TSLB, COM11 */
+ { 0x3D, 0x90 }, { 0x3E, 0x02 }, { 0x3F, 0xF2 }, /* COM13, COM14, EDGE */
+ { 0x41, 0x02 }, { 0x42, 0xC8 }, /* COM16, COM17 */
+ { 0x43, 0xF0 }, { 0x44, 0x10 }, { 0x45, 0x6C }, /* ?, ?, ? */
+ { 0x46, 0x6C }, { 0x47, 0x44 }, { 0x48, 0x44 }, /* ?, ?, ? */
+ { 0x49, 0x03 }, { 0x59, 0x49 }, { 0x5A, 0x94 }, /* ?, ?, ? */
+ { 0x5B, 0x46 }, { 0x5C, 0x84 }, { 0x5D, 0x5C }, /* ?, ?, ? */
+ { 0x5E, 0x08 }, { 0x5F, 0x00 }, { 0x60, 0x14 }, /* ?, ?, ? */
+ { 0x61, 0xCE }, /* ? */
+ { 0x62, 0x70 }, { 0x63, 0x00 }, { 0x64, 0x04 }, /* LCC1, LCC2, LCC3 */
+ { 0x65, 0x00 }, { 0x66, 0x00 }, /* LCC4, LCC5 */
+ { 0x69, 0x00 }, { 0x6A, 0x3E }, { 0x6B, 0x3F }, /* HV, MBD, DBLV */
+ { 0x6C, 0x40 }, { 0x6D, 0x30 }, { 0x6E, 0x4B }, /* GSP1, GSP2, GSP3 */
+ { 0x6F, 0x60 }, { 0x70, 0x70 }, { 0x71, 0x70 }, /* GSP4, GSP5, GSP6 */
+ { 0x72, 0x70 }, { 0x73, 0x70 }, { 0x74, 0x60 }, /* GSP7, GSP8, GSP9 */
+ { 0x75, 0x60 }, { 0x76, 0x50 }, { 0x77, 0x48 }, /* GSP10,GSP11,GSP12 */
+ { 0x78, 0x3A }, { 0x79, 0x2E }, { 0x7A, 0x28 }, /* GSP13,GSP14,GSP15 */
+ { 0x7B, 0x22 }, { 0x7C, 0x04 }, { 0x7D, 0x07 }, /* GSP16,GST1, GST2 */
+ { 0x7E, 0x10 }, { 0x7F, 0x28 }, { 0x80, 0x36 }, /* GST3, GST4, GST5 */
+ { 0x81, 0x44 }, { 0x82, 0x52 }, { 0x83, 0x60 }, /* GST6, GST7, GST8 */
+ { 0x84, 0x6C }, { 0x85, 0x78 }, { 0x86, 0x8C }, /* GST9, GST10,GST11 */
+ { 0x87, 0x9E }, { 0x88, 0xBB }, { 0x89, 0xD2 }, /* GST12,GST13,GST14 */
+ { 0x8A, 0xE6 }, { 0x13, 0xaF }, { 0x15, 0x02 }, /* GST15, COM8 */
+ { 0x22, 0x8a }, /* GROS */
+ { OV9640_REG_TERM, OV9640_VAL_TERM }
+};
+
+static int ov9640_sensor_power_set(int power)
+{
+ unsigned char expa;
+ int err;
+
+ /* read current state of GPIO EXPA outputs */
+ err = read_gpio_expa(&expa, 0x27);
+ if (err) {
+ printk(KERN_ERR "Error reading GPIO EXPA\n");
+ return err;
+ }
+ /* Clear GPIO EXPA P3 (CAMERA_MODULE_EN) to power-up/down sensor */
+ if (power)
+ expa |= 0x08;
+ else
+ expa &= ~0x08;
+
+ err = write_gpio_expa(expa, 0x27);
+ if (err) {
+ printk(KERN_ERR "Error writing to GPIO EXPA\n");
+ return err;
+ }
+
+ return err;
+}
+
+static struct v4l2_ifparm ifparm = {
+ .if_type = V4L2_IF_TYPE_BT656,
+ .u = {
+ .bt656 = {
+ .frame_start_on_rising_vs = 1,
+ .nobt_vs_inv = 1,
+ .mode = V4L2_IF_TYPE_BT656_MODE_NOBT_8BIT,
+ .clock_min = OV9640_XCLK_MIN,
+ .clock_max = OV9640_XCLK_MAX,
+ },
+ },
+};
+
+static int ov9640_ifparm(struct v4l2_ifparm *p)
+{
+ *p = ifparm;
+
+ return 0;
+}
+
+static struct ov9640_platform_data h3_ov9640_platform_data = {
+ .power_set = ov9640_sensor_power_set,
+ .default_regs = ov9640_common,
+ .ifparm = ov9640_ifparm,
+};
+#endif
+
+static struct i2c_board_info __initdata h3_i2c_board_info[] = {
+#if defined(CONFIG_VIDEO_OV9640) || defined(CONFIG_VIDEO_OV9640_MODULE)
+ {
+ I2C_BOARD_INFO("ov9640", 0x30),
+ .platform_data = &h3_ov9640_platform_data,
+ },
+#endif
+ {
+ I2C_BOARD_INFO("isp1301_omap", 0x2d),
+ .type = "isp1301_omap",
+ .irq = OMAP_GPIO_IRQ(14),
+ },
+};
+
static void __init h3_init(void)
{
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
/* GPIO10 pullup/down register, Enable pullup on GPIO10 */
omap_cfg_reg(V2_1710_GPIO10);
+ /* TSC2101 */
+ omap_cfg_reg(W19_1610_GPIO48);
+ gpio_request(H3_TS_GPIO, "tsc_irq");
+ gpio_direction_input(H3_TS_GPIO);
+ omap_cfg_reg(N14_1610_UWIRE_CS0);
+
platform_add_devices(devices, ARRAY_SIZE(devices));
spi_register_board_info(h3_spi_board_info,
ARRAY_SIZE(h3_spi_board_info));
omap_register_i2c_bus(1, 100, h3_i2c_board_info,
ARRAY_SIZE(h3_i2c_board_info));
h3_mmc_init();
+ omap_register_gpio_switches(h3_gpio_switches,
+ ARRAY_SIZE(h3_gpio_switches));
}
static void __init h3_init_smc91x(void)
projects / linux-2.6-omap-h63xx.git / blobdiff