#include <mach/keypad.h>
#include <mach/dma.h>
#include <mach/common.h>
-#include <mach/mcbsp.h>
-#include <mach/omap-alsa.h>
#define H3_TS_GPIO 48
},
};
-static struct omap_mcbsp_reg_cfg mcbsp_regs = {
- .spcr2 = FREE | FRST | GRST | XRST | XINTM(3),
- .spcr1 = RINTM(3) | RRST,
- .rcr2 = RPHASE | RFRLEN2(OMAP_MCBSP_WORD_8) |
- RWDLEN2(OMAP_MCBSP_WORD_16) | RDATDLY(1),
- .rcr1 = RFRLEN1(OMAP_MCBSP_WORD_8) | RWDLEN1(OMAP_MCBSP_WORD_16),
- .xcr2 = XPHASE | XFRLEN2(OMAP_MCBSP_WORD_8) |
- XWDLEN2(OMAP_MCBSP_WORD_16) | XDATDLY(1) | XFIG,
- .xcr1 = XFRLEN1(OMAP_MCBSP_WORD_8) | XWDLEN1(OMAP_MCBSP_WORD_16),
- .srgr1 = FWID(15),
- .srgr2 = GSYNC | CLKSP | FSGM | FPER(31),
-
- .pcr0 = CLKRM | SCLKME | FSXP | FSRP | CLKXP | CLKRP,
- /*.pcr0 = CLKXP | CLKRP,*/ /* mcbsp: slave */
-};
-
-static struct omap_alsa_codec_config alsa_config = {
- .name = "H3 TSC2101",
- .mcbsp_regs_alsa = &mcbsp_regs,
- .codec_configure_dev = NULL, /* tsc2101_configure, */
- .codec_set_samplerate = NULL, /* tsc2101_set_samplerate, */
- .codec_clock_setup = NULL, /* tsc2101_clock_setup, */
- .codec_clock_on = NULL, /* tsc2101_clock_on, */
- .codec_clock_off = NULL, /* tsc2101_clock_off, */
- .get_default_samplerate = NULL, /* tsc2101_get_default_samplerate, */
-};
-
-static struct platform_device h3_mcbsp1_device = {
- .name = "omap_alsa_mcbsp",
- .id = 1,
- .dev = {
- .platform_data = &alsa_config,
- },
-};
-
static struct platform_device *devices[] __initdata = {
&nor_device,
&nand_device,
&h3_irda_device,
&h3_kp_device,
&h3_lcd_device,
- &h3_mcbsp1_device,
};
static struct omap_usb_config h3_usb_config __initdata = {
.pins[1] = 3,
};
-static struct omap_mmc_config h3_mmc_config __initdata = {
- .mmc[0] = {
- .enabled = 1,
- .wire4 = 1,
- },
-};
-
-extern struct omap_mmc_platform_data h3_mmc_data;
-
static struct omap_uart_config h3_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
static struct omap_board_config_kernel h3_config[] __initdata = {
{ OMAP_TAG_USB, &h3_usb_config },
- { OMAP_TAG_MMC, &h3_mmc_config },
{ OMAP_TAG_UART, &h3_uart_config },
{ OMAP_TAG_LCD, &h3_lcd_config },
};
},
};
-static struct omap_gpio_switch h3_gpio_switches[] __initdata = {
- {
- .name = "mmc_slot",
- .gpio = OMAP_MPUIO(1),
- .type = OMAP_GPIO_SWITCH_TYPE_COVER,
- .debounce_rising = 100,
- .debounce_falling = 0,
- .notify = h3_mmc_slot_cover_handler,
- .notify_data = NULL,
- },
-};
-
#define H3_NAND_RB_GPIO_PIN 10
static int nand_dev_ready(struct omap_nand_platform_data *data)
{
- return omap_get_gpio_datain(H3_NAND_RB_GPIO_PIN);
+ return gpio_get_value(H3_NAND_RB_GPIO_PIN);
}
static void __init h3_init(void)
nand_resource.end = nand_resource.start = OMAP_CS2B_PHYS;
nand_resource.end += SZ_4K - 1;
- if (!(omap_request_gpio(H3_NAND_RB_GPIO_PIN)))
- nand_data.dev_ready = nand_dev_ready;
+ if (gpio_request(H3_NAND_RB_GPIO_PIN, "NAND ready") < 0)
+ BUG();
+ nand_data.dev_ready = nand_dev_ready;
/* GPIO10 Func_MUX_CTRL reg bit 29:27, Configure V2 to mode1 as GPIO */
/* GPIO10 pullup/down register, Enable pullup on GPIO10 */
static void __init h3_init_smc91x(void)
{
omap_cfg_reg(W15_1710_GPIO40);
- if (omap_request_gpio(40) < 0) {
+ if (gpio_request(40, "SMC91x irq") < 0) {
printk("Error requesting gpio 40 for smc91x irq\n");
return;
}