#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/fb.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
#include <video/atmel_lcdc.h>
#include <asm/arch/board.h>
#include <asm/arch/gpio.h>
-#include <asm/arch/at91sam926x_mc.h>
+#include <asm/arch/at91sam9_smc.h>
#include "generic.h"
-/*
- * Serial port configuration.
- * 0 .. 2 = USART0 .. USART2
- * 3 = DBGU
- */
-static struct at91_uart_config __initdata ek_uart_config = {
- .console_tty = 0, /* ttyS0 */
- .nr_tty = 2,
- .tty_map = { 3, 0, -1, -1, } /* ttyS0, ..., ttyS3 */
-};
-
static void __init ek_map_io(void)
{
/* Initialize processor: 16.367 MHz crystal */
at91sam9263_initialize(16367660);
- /* Setup the serial ports and console */
- at91_init_serial(&ek_uart_config);
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
}
static void __init ek_init_irq(void)
* MACB Ethernet device
*/
static struct at91_eth_data __initdata ek_macb_data = {
+ .phy_irq_pin = AT91_PIN_PE31,
.is_rmii = 1,
};
static void at91_lcdc_power_control(int on)
{
- if (on)
- at91_set_gpio_value(AT91_PIN_PD12, 0); /* power up */
- else
- at91_set_gpio_value(AT91_PIN_PD12, 1); /* power down */
+ at91_set_gpio_value(AT91_PIN_PA30, on);
}
/* Driver datas */
static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+ .lcdcon_is_backlight = true,
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
.default_lcdcon2 = AT91SAM9263_DEFAULT_LCDCON2,
#endif
+/*
+ * GPIO Buttons
+ */
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+static struct gpio_keys_button ek_buttons[] = {
+ { /* BP1, "leftclic" */
+ .code = BTN_LEFT,
+ .gpio = AT91_PIN_PC5,
+ .active_low = 1,
+ .desc = "left_click",
+ .wakeup = 1,
+ },
+ { /* BP2, "rightclic" */
+ .code = BTN_RIGHT,
+ .gpio = AT91_PIN_PC4,
+ .active_low = 1,
+ .desc = "right_click",
+ .wakeup = 1,
+ },
+};
+
+static struct gpio_keys_platform_data ek_button_data = {
+ .buttons = ek_buttons,
+ .nbuttons = ARRAY_SIZE(ek_buttons),
+};
+
+static struct platform_device ek_button_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &ek_button_data,
+ }
+};
+
+static void __init ek_add_device_buttons(void)
+{
+ at91_set_GPIO_periph(AT91_PIN_PC5, 0); /* left button */
+ at91_set_deglitch(AT91_PIN_PC5, 1);
+ at91_set_GPIO_periph(AT91_PIN_PC4, 0); /* right button */
+ at91_set_deglitch(AT91_PIN_PC4, 1);
+
+ platform_device_register(&ek_button_device);
+}
+#else
+static void __init ek_add_device_buttons(void) {}
+#endif
+
+
/*
* AC97
*/
};
+/*
+ * LEDs ... these could all be PWM-driven, for variable brightness
+ */
+static struct gpio_led ek_leds[] = {
+ { /* "left" led, green, userled1, pwm1 */
+ .name = "ds1",
+ .gpio = AT91_PIN_PB8,
+ .active_low = 1,
+ .default_trigger = "mmc0",
+ },
+ { /* "right" led, green, userled2, pwm2 */
+ .name = "ds2",
+ .gpio = AT91_PIN_PC29,
+ .active_low = 1,
+ .default_trigger = "nand-disk",
+ },
+ { /* "power" led, yellow, pwm0 */
+ .name = "ds3",
+ .gpio = AT91_PIN_PB7,
+ .default_trigger = "heartbeat",
+ }
+};
+
+
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_i2c(NULL, 0);
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
+ /* Push Buttons */
+ ek_add_device_buttons();
/* AC97 */
at91_add_device_ac97(&ek_ac97_data);
+ /* LEDs */
+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")