#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
+#include <linux/spi/at73c213.h>
+#include <linux/clk.h>
#include <linux/dm9000.h>
#include <linux/fb.h>
#include <linux/gpio_keys.h>
#include <asm/arch/board.h>
#include <asm/arch/gpio.h>
-#include <asm/arch/at91sam926x_mc.h>
+#include <asm/arch/at91sam9_smc.h>
#include "generic.h"
-/*
- * Serial port configuration.
- * 0 .. 2 = USART0 .. USART2
- * 3 = DBGU
- */
-static struct at91_uart_config __initdata ek_uart_config = {
- .console_tty = 0, /* ttyS0 */
- .nr_tty = 1,
- .tty_map = { 3, -1, -1, -1 } /* ttyS0, ..., ttyS3 */
-};
-
static void __init ek_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
/* Setup the LEDs */
at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14);
- /* Setup the serial ports and console */
- at91_init_serial(&ek_uart_config);
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
}
static void __init ek_init_irq(void)
static void __init ek_add_device_ts(void) {}
#endif
+/*
+ * Audio
+ */
+static struct at73c213_board_info at73c213_data = {
+ .ssc_id = 1,
+ .shortname = "AT91SAM9261-EK external DAC",
+};
+
+#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
+static void __init at73c213_set_clk(struct at73c213_board_info *info)
+{
+ struct clk *pck2;
+ struct clk *plla;
+
+ pck2 = clk_get(NULL, "pck2");
+ plla = clk_get(NULL, "plla");
+
+ /* AT73C213 MCK Clock */
+ at91_set_B_periph(AT91_PIN_PB31, 0); /* PCK2 */
+
+ clk_set_parent(pck2, plla);
+ clk_put(plla);
+
+ info->dac_clk = pck2;
+}
+#else
+static void __init at73c213_set_clk(struct at73c213_board_info *info) {}
+#endif
+
/*
* SPI devices
*/
.bus_num = 0,
.platform_data = &ads_info,
.irq = AT91SAM9261_ID_IRQ0,
+ .controller_data = (void *) AT91_PIN_PA28, /* CS pin */
},
#endif
#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
.chip_select = 3,
.max_speed_hz = 10 * 1000 * 1000,
.bus_num = 0,
+ .mode = SPI_MODE_1,
+ .platform_data = &at73c213_data,
+ .controller_data = (void*) AT91_PIN_PA29, /* default for CS3 is PA6, but it must be PA29 */
},
#endif
};
* LCD Controller
*/
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
+
+#if defined(CONFIG_FB_ATMEL_STN)
+
+/* STN */
+static struct fb_videomode at91_stn_modes[] = {
+ {
+ .name = "SP06Q002 @ 75",
+ .refresh = 75,
+ .xres = 320, .yres = 240,
+ .pixclock = KHZ2PICOS(1440),
+
+ .left_margin = 1, .right_margin = 1,
+ .upper_margin = 0, .lower_margin = 0,
+ .hsync_len = 1, .vsync_len = 1,
+
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+};
+
+static struct fb_monspecs at91fb_default_stn_monspecs = {
+ .manufacturer = "HIT",
+ .monitor = "SP06Q002",
+
+ .modedb = at91_stn_modes,
+ .modedb_len = ARRAY_SIZE(at91_stn_modes),
+ .hfmin = 15000,
+ .hfmax = 64000,
+ .vfmin = 50,
+ .vfmax = 150,
+};
+
+#define AT91SAM9261_DEFAULT_STN_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
+ | ATMEL_LCDC_DISTYPE_STNMONO \
+ | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE \
+ | ATMEL_LCDC_IFWIDTH_4 \
+ | ATMEL_LCDC_SCANMOD_SINGLE)
+
+static void at91_lcdc_stn_power_control(int on)
+{
+ /* backlight */
+ if (on) { /* power up */
+ at91_set_gpio_value(AT91_PIN_PC14, 0);
+ at91_set_gpio_value(AT91_PIN_PC15, 0);
+ } else { /* power down */
+ at91_set_gpio_value(AT91_PIN_PC14, 1);
+ at91_set_gpio_value(AT91_PIN_PC15, 1);
+ }
+}
+
+static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+ .default_bpp = 1,
+ .default_dmacon = ATMEL_LCDC_DMAEN,
+ .default_lcdcon2 = AT91SAM9261_DEFAULT_STN_LCDCON2,
+ .default_monspecs = &at91fb_default_stn_monspecs,
+ .atmel_lcdfb_power_control = at91_lcdc_stn_power_control,
+ .guard_time = 1,
+};
+
+#else
+
+/* TFT */
static struct fb_videomode at91_tft_vga_modes[] = {
{
.name = "TX09D50VM1CCA @ 60",
},
};
-static struct fb_monspecs at91fb_default_monspecs = {
+static struct fb_monspecs at91fb_default_tft_monspecs = {
.manufacturer = "HIT",
.monitor = "TX09D50VM1CCA",
.vfmax = 150,
};
-#define AT91SAM9261_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
+#define AT91SAM9261_DEFAULT_TFT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
| ATMEL_LCDC_DISTYPE_TFT \
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-static void at91_lcdc_power_control(int on)
+static void at91_lcdc_tft_power_control(int on)
{
if (on)
at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
}
-/* Driver datas */
static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+ .lcdcon_is_backlight = true,
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
- .default_lcdcon2 = AT91SAM9261_DEFAULT_LCDCON2,
- .default_monspecs = &at91fb_default_monspecs,
- .atmel_lcdfb_power_control = at91_lcdc_power_control,
+ .default_lcdcon2 = AT91SAM9261_DEFAULT_TFT_LCDCON2,
+ .default_monspecs = &at91fb_default_tft_monspecs,
+ .atmel_lcdfb_power_control = at91_lcdc_tft_power_control,
.guard_time = 1,
};
+#endif
#else
static struct atmel_lcdfb_info __initdata ek_lcdc_data;
static struct gpio_keys_button ek_buttons[] = {
{
.gpio = AT91_PIN_PA27,
- .keycode = BTN_0,
+ .code = BTN_0,
.desc = "Button 0",
.active_low = 1,
},
{
.gpio = AT91_PIN_PA26,
- .keycode = BTN_1,
+ .code = BTN_1,
.desc = "Button 1",
.active_low = 1,
},
{
.gpio = AT91_PIN_PA25,
- .keycode = BTN_2,
+ .code = BTN_2,
.desc = "Button 2",
.active_low = 1,
},
{
.gpio = AT91_PIN_PA24,
- .keycode = BTN_3,
+ .code = BTN_3,
.desc = "Button 3",
.active_low = 1,
}
static void __init ek_add_device_buttons(void)
{
- at91_set_gpio_input(AT91_PIN_PB27, 0); /* btn0 */
- at91_set_deglitch(AT91_PIN_PB27, 1);
- at91_set_gpio_input(AT91_PIN_PB26, 0); /* btn1 */
- at91_set_deglitch(AT91_PIN_PB26, 1);
- at91_set_gpio_input(AT91_PIN_PB25, 0); /* btn2 */
- at91_set_deglitch(AT91_PIN_PB25, 1);
- at91_set_gpio_input(AT91_PIN_PB24, 0); /* btn3 */
- at91_set_deglitch(AT91_PIN_PB24, 1);
+ at91_set_gpio_input(AT91_PIN_PA27, 0); /* btn0 */
+ at91_set_deglitch(AT91_PIN_PA27, 1);
+ at91_set_gpio_input(AT91_PIN_PA26, 0); /* btn1 */
+ at91_set_deglitch(AT91_PIN_PA26, 1);
+ at91_set_gpio_input(AT91_PIN_PA25, 0); /* btn2 */
+ at91_set_deglitch(AT91_PIN_PA25, 1);
+ at91_set_gpio_input(AT91_PIN_PA24, 0); /* btn3 */
+ at91_set_deglitch(AT91_PIN_PA24, 1);
platform_device_register(&ek_button_device);
}
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* I2C */
- at91_add_device_i2c();
+ at91_add_device_i2c(NULL, 0);
/* NAND */
at91_add_device_nand(&ek_nand_data);
/* DM9000 ethernet */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* Touchscreen */
ek_add_device_ts();
+ /* SSC (to AT73C213) */
+ at73c213_set_clk(&at73c213_data);
+ at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX);
#else
/* MMC */
at91_add_device_mmc(0, &ek_mmc_data);