#include <asm/arch/gpio.h>
#include <asm/arch/at91sam9261.h>
#include <asm/arch/at91sam9261_matrix.h>
-#include <asm/arch/at91sam926x_mc.h>
+#include <asm/arch/at91sam9_smc.h>
#include "generic.h"
void __init at91_add_device_udc(struct at91_udc_data *data)
{
- unsigned long x;
-
if (!data)
return;
at91_set_deglitch(data->vbus_pin, 1);
}
- /* Pullup pin is handled internally */
- x = at91_sys_read(AT91_MATRIX_USBPUCR);
- at91_sys_write(AT91_MATRIX_USBPUCR, x | AT91_MATRIX_USBPUCR_PUON);
+ /* Pullup pin is handled internally by USB device peripheral */
udc_data = *data;
platform_device_register(&at91sam9261_udc_device);
return;
csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC);
+ at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* set the bus interface characteristics */
at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0)
#endif
+/* --------------------------------------------------------------------
+ * Timer/Counter block
+ * -------------------------------------------------------------------- */
+
+#ifdef CONFIG_ATMEL_TCLIB
+
+static struct resource tcb_resources[] = {
+ [0] = {
+ .start = AT91SAM9261_BASE_TCB0,
+ .end = AT91SAM9261_BASE_TCB0 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9261_ID_TC0,
+ .end = AT91SAM9261_ID_TC0,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AT91SAM9261_ID_TC1,
+ .end = AT91SAM9261_ID_TC1,
+ .flags = IORESOURCE_IRQ,
+ },
+ [3] = {
+ .start = AT91SAM9261_ID_TC2,
+ .end = AT91SAM9261_ID_TC2,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9261_tcb_device = {
+ .name = "atmel_tcb",
+ .id = 0,
+ .resource = tcb_resources,
+ .num_resources = ARRAY_SIZE(tcb_resources),
+};
+
+static void __init at91_add_device_tc(void)
+{
+ /* this chip has a separate clock and irq for each TC channel */
+ at91_clock_associate("tc0_clk", &at91sam9261_tcb_device.dev, "t0_clk");
+ at91_clock_associate("tc1_clk", &at91sam9261_tcb_device.dev, "t1_clk");
+ at91_clock_associate("tc2_clk", &at91sam9261_tcb_device.dev, "t2_clk");
+ platform_device_register(&at91sam9261_tcb_device);
+}
+#else
+static void __init at91_add_device_tc(void) { }
+#endif
+
+
/* --------------------------------------------------------------------
* RTT
* -------------------------------------------------------------------- */
static struct platform_device at91sam9261_rtt_device = {
.name = "at91_rtt",
- .id = -1,
+ .id = 0,
.resource = rtt_resources,
.num_resources = ARRAY_SIZE(rtt_resources),
};
/* --------------------------------------------------------------------
- * LEDs
+ * SSC -- Synchronous Serial Controller
* -------------------------------------------------------------------- */
-#if defined(CONFIG_LEDS)
-u8 at91_leds_cpu;
-u8 at91_leds_timer;
+#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
+static u64 ssc0_dmamask = DMA_BIT_MASK(32);
-void __init at91_init_leds(u8 cpu_led, u8 timer_led)
+static struct resource ssc0_resources[] = {
+ [0] = {
+ .start = AT91SAM9261_BASE_SSC0,
+ .end = AT91SAM9261_BASE_SSC0 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9261_ID_SSC0,
+ .end = AT91SAM9261_ID_SSC0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9261_ssc0_device = {
+ .name = "ssc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ssc0_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc0_resources,
+ .num_resources = ARRAY_SIZE(ssc0_resources),
+};
+
+static inline void configure_ssc0_pins(unsigned pins)
{
- /* Enable GPIO to access the LEDs */
- at91_set_gpio_output(cpu_led, 1);
- at91_set_gpio_output(timer_led, 1);
+ if (pins & ATMEL_SSC_TF)
+ at91_set_A_periph(AT91_PIN_PB21, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_A_periph(AT91_PIN_PB22, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_A_periph(AT91_PIN_PB23, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_A_periph(AT91_PIN_PB24, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_A_periph(AT91_PIN_PB25, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_A_periph(AT91_PIN_PB26, 1);
+}
- at91_leds_cpu = cpu_led;
- at91_leds_timer = timer_led;
+static u64 ssc1_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc1_resources[] = {
+ [0] = {
+ .start = AT91SAM9261_BASE_SSC1,
+ .end = AT91SAM9261_BASE_SSC1 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9261_ID_SSC1,
+ .end = AT91SAM9261_ID_SSC1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9261_ssc1_device = {
+ .name = "ssc",
+ .id = 1,
+ .dev = {
+ .dma_mask = &ssc1_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc1_resources,
+ .num_resources = ARRAY_SIZE(ssc1_resources),
+};
+
+static inline void configure_ssc1_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_B_periph(AT91_PIN_PA17, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_B_periph(AT91_PIN_PA18, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_B_periph(AT91_PIN_PA19, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_B_periph(AT91_PIN_PA20, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_B_periph(AT91_PIN_PA21, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_B_periph(AT91_PIN_PA22, 1);
+}
+
+static u64 ssc2_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc2_resources[] = {
+ [0] = {
+ .start = AT91SAM9261_BASE_SSC2,
+ .end = AT91SAM9261_BASE_SSC2 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9261_ID_SSC2,
+ .end = AT91SAM9261_ID_SSC2,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9261_ssc2_device = {
+ .name = "ssc",
+ .id = 2,
+ .dev = {
+ .dma_mask = &ssc2_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc2_resources,
+ .num_resources = ARRAY_SIZE(ssc2_resources),
+};
+
+static inline void configure_ssc2_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_B_periph(AT91_PIN_PC25, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_B_periph(AT91_PIN_PC26, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_B_periph(AT91_PIN_PC27, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_B_periph(AT91_PIN_PC28, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_B_periph(AT91_PIN_PC29, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_B_periph(AT91_PIN_PC30, 1);
}
+
+/*
+ * SSC controllers are accessed through library code, instead of any
+ * kind of all-singing/all-dancing driver. For example one could be
+ * used by a particular I2S audio codec's driver, while another one
+ * on the same system might be used by a custom data capture driver.
+ */
+void __init at91_add_device_ssc(unsigned id, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ /*
+ * NOTE: caller is responsible for passing information matching
+ * "pins" to whatever will be using each particular controller.
+ */
+ switch (id) {
+ case AT91SAM9261_ID_SSC0:
+ pdev = &at91sam9261_ssc0_device;
+ configure_ssc0_pins(pins);
+ at91_clock_associate("ssc0_clk", &pdev->dev, "pclk");
+ break;
+ case AT91SAM9261_ID_SSC1:
+ pdev = &at91sam9261_ssc1_device;
+ configure_ssc1_pins(pins);
+ at91_clock_associate("ssc1_clk", &pdev->dev, "pclk");
+ break;
+ case AT91SAM9261_ID_SSC2:
+ pdev = &at91sam9261_ssc2_device;
+ configure_ssc2_pins(pins);
+ at91_clock_associate("ssc2_clk", &pdev->dev, "pclk");
+ break;
+ default:
+ return;
+ }
+
+ platform_device_register(pdev);
+}
+
#else
-void __init at91_init_leds(u8 cpu_led, u8 timer_led) {}
+void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
#endif
.num_resources = ARRAY_SIZE(uart0_resources),
};
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PC8, 1); /* TXD0 */
at91_set_A_periph(AT91_PIN_PC9, 0); /* RXD0 */
- at91_set_A_periph(AT91_PIN_PC10, 0); /* RTS0 */
- at91_set_A_periph(AT91_PIN_PC11, 0); /* CTS0 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PC10, 0); /* RTS0 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PC11, 0); /* CTS0 */
}
static struct resource uart1_resources[] = {
.num_resources = ARRAY_SIZE(uart1_resources),
};
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PC12, 1); /* TXD1 */
at91_set_A_periph(AT91_PIN_PC13, 0); /* RXD1 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PA12, 0); /* RTS1 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PA13, 0); /* CTS1 */
}
static struct resource uart2_resources[] = {
.num_resources = ARRAY_SIZE(uart2_resources),
};
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PC15, 0); /* RXD2 */
at91_set_A_periph(AT91_PIN_PC14, 1); /* TXD2 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PA15, 0); /* RTS2*/
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PA16, 0); /* CTS2 */
}
-static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
+static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
struct platform_device *atmel_default_console_device; /* the serial console device */
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
{
- int i;
-
- /* Fill in list of supported UARTs */
- for (i = 0; i < config->nr_tty; i++) {
- switch (config->tty_map[i]) {
- case 0:
- configure_usart0_pins();
- at91_uarts[i] = &at91sam9261_uart0_device;
- at91_clock_associate("usart0_clk", &at91sam9261_uart0_device.dev, "usart");
- break;
- case 1:
- configure_usart1_pins();
- at91_uarts[i] = &at91sam9261_uart1_device;
- at91_clock_associate("usart1_clk", &at91sam9261_uart1_device.dev, "usart");
- break;
- case 2:
- configure_usart2_pins();
- at91_uarts[i] = &at91sam9261_uart2_device;
- at91_clock_associate("usart2_clk", &at91sam9261_uart2_device.dev, "usart");
- break;
- case 3:
- configure_dbgu_pins();
- at91_uarts[i] = &at91sam9261_dbgu_device;
- at91_clock_associate("mck", &at91sam9261_dbgu_device.dev, "usart");
- break;
- default:
- continue;
- }
- at91_uarts[i]->id = i; /* update ID number to mapped ID */
+ struct platform_device *pdev;
+
+ switch (id) {
+ case 0: /* DBGU */
+ pdev = &at91sam9261_dbgu_device;
+ configure_dbgu_pins();
+ at91_clock_associate("mck", &pdev->dev, "usart");
+ break;
+ case AT91SAM9261_ID_US0:
+ pdev = &at91sam9261_uart0_device;
+ configure_usart0_pins(pins);
+ at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9261_ID_US1:
+ pdev = &at91sam9261_uart1_device;
+ configure_usart1_pins(pins);
+ at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9261_ID_US2:
+ pdev = &at91sam9261_uart2_device;
+ configure_usart2_pins(pins);
+ at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+ break;
+ default:
+ return;
}
+ pdev->id = portnr; /* update to mapped ID */
- /* Set serial console device */
- if (config->console_tty < ATMEL_MAX_UART)
- atmel_default_console_device = at91_uarts[config->console_tty];
- if (!atmel_default_console_device)
- printk(KERN_INFO "AT91: No default serial console defined.\n");
+ if (portnr < ATMEL_MAX_UART)
+ at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+ if (portnr < ATMEL_MAX_UART)
+ atmel_default_console_device = at91_uarts[portnr];
}
void __init at91_add_device_serial(void)
if (at91_uarts[i])
platform_device_register(at91_uarts[i]);
}
+
+ if (!atmel_default_console_device)
+ printk(KERN_INFO "AT91: No default serial console defined.\n");
}
#else
-void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
{
at91_add_device_rtt();
at91_add_device_watchdog();
+ at91_add_device_tc();
return 0;
}
projects / linux-2.6-omap-h63xx.git / blobdiff