static struct resource nand_resources[] = {
{
.start = NAND_BASE,
- .end = NAND_BASE + SZ_8M - 1,
+ .end = NAND_BASE + SZ_256M - 1,
.flags = IORESOURCE_MEM,
}
};
return;
csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC);
+ at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* set the bus interface characteristics */
at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0)
#endif
-/* --------------------------------------------------------------------
- * LEDs
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_LEDS)
-u8 at91_leds_cpu;
-u8 at91_leds_timer;
-
-void __init at91_init_leds(u8 cpu_led, u8 timer_led)
-{
- /* Enable GPIO to access the LEDs */
- at91_set_gpio_output(cpu_led, 1);
- at91_set_gpio_output(timer_led, 1);
-
- at91_leds_cpu = cpu_led;
- at91_leds_timer = timer_led;
-}
-#else
-void __init at91_init_leds(u8 cpu_led, u8 timer_led) {}
-#endif
-
-
/* --------------------------------------------------------------------
* SSC -- Synchronous Serial Controller
* -------------------------------------------------------------------- */
.num_resources = ARRAY_SIZE(uart0_resources),
};
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PB4, 1); /* TXD0 */
at91_set_A_periph(AT91_PIN_PB5, 0); /* RXD0 */
- at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS0 */
- at91_set_A_periph(AT91_PIN_PB27, 0); /* CTS0 */
- at91_set_A_periph(AT91_PIN_PB24, 0); /* DTR0 */
- at91_set_A_periph(AT91_PIN_PB22, 0); /* DSR0 */
- at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD0 */
- at91_set_A_periph(AT91_PIN_PB25, 0); /* RI0 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS0 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PB27, 0); /* CTS0 */
+ if (pins & ATMEL_UART_DTR)
+ at91_set_A_periph(AT91_PIN_PB24, 0); /* DTR0 */
+ if (pins & ATMEL_UART_DSR)
+ at91_set_A_periph(AT91_PIN_PB22, 0); /* DSR0 */
+ if (pins & ATMEL_UART_DCD)
+ at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD0 */
+ if (pins & ATMEL_UART_RI)
+ at91_set_A_periph(AT91_PIN_PB25, 0); /* RI0 */
}
static struct resource uart1_resources[] = {
.num_resources = ARRAY_SIZE(uart1_resources),
};
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PB6, 1); /* TXD1 */
at91_set_A_periph(AT91_PIN_PB7, 0); /* RXD1 */
- at91_set_A_periph(AT91_PIN_PB28, 0); /* RTS1 */
- at91_set_A_periph(AT91_PIN_PB29, 0); /* CTS1 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PB28, 0); /* RTS1 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PB29, 0); /* CTS1 */
}
static struct resource uart2_resources[] = {
.num_resources = ARRAY_SIZE(uart2_resources),
};
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PB8, 1); /* TXD2 */
at91_set_A_periph(AT91_PIN_PB9, 0); /* RXD2 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PA4, 0); /* RTS2 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PA5, 0); /* CTS2 */
}
static struct resource uart3_resources[] = {
.num_resources = ARRAY_SIZE(uart3_resources),
};
-static inline void configure_usart3_pins(void)
+static inline void configure_usart3_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PB10, 1); /* TXD3 */
at91_set_A_periph(AT91_PIN_PB11, 0); /* RXD3 */
+
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PC8, 0); /* RTS3 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PC10, 0); /* CTS3 */
}
static struct resource uart4_resources[] = {
static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
struct platform_device *atmel_default_console_device; /* the serial console device */
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
{
int i;
for (i = 0; i < config->nr_tty; i++) {
switch (config->tty_map[i]) {
case 0:
- configure_usart0_pins();
+ configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DSR | ATMEL_UART_DTR | ATMEL_UART_DCD | ATMEL_UART_RI);
at91_uarts[i] = &at91sam9260_uart0_device;
at91_clock_associate("usart0_clk", &at91sam9260_uart0_device.dev, "usart");
break;
case 1:
- configure_usart1_pins();
+ configure_usart1_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_uarts[i] = &at91sam9260_uart1_device;
at91_clock_associate("usart1_clk", &at91sam9260_uart1_device.dev, "usart");
break;
case 2:
- configure_usart2_pins();
+ configure_usart2_pins(0);
at91_uarts[i] = &at91sam9260_uart2_device;
at91_clock_associate("usart2_clk", &at91sam9260_uart2_device.dev, "usart");
break;
case 3:
- configure_usart3_pins();
+ configure_usart3_pins(0);
at91_uarts[i] = &at91sam9260_uart3_device;
at91_clock_associate("usart3_clk", &at91sam9260_uart3_device.dev, "usart");
break;
printk(KERN_INFO "AT91: No default serial console defined.\n");
}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ switch (id) {
+ case 0: /* DBGU */
+ pdev = &at91sam9260_dbgu_device;
+ configure_dbgu_pins();
+ at91_clock_associate("mck", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US0:
+ pdev = &at91sam9260_uart0_device;
+ configure_usart0_pins(pins);
+ at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US1:
+ pdev = &at91sam9260_uart1_device;
+ configure_usart1_pins(pins);
+ at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US2:
+ pdev = &at91sam9260_uart2_device;
+ configure_usart2_pins(pins);
+ at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US3:
+ pdev = &at91sam9260_uart3_device;
+ configure_usart3_pins(pins);
+ at91_clock_associate("usart3_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US4:
+ pdev = &at91sam9260_uart4_device;
+ configure_usart4_pins();
+ at91_clock_associate("usart4_clk", &pdev->dev, "usart");
+ break;
+ case AT91SAM9260_ID_US5:
+ pdev = &at91sam9260_uart5_device;
+ configure_usart5_pins();
+ at91_clock_associate("usart5_clk", &pdev->dev, "usart");
+ break;
+ default:
+ return;
+ }
+ pdev->id = portnr; /* update to mapped ID */
+
+ if (portnr < ATMEL_MAX_UART)
+ at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+ if (portnr < ATMEL_MAX_UART)
+ atmel_default_console_device = at91_uarts[portnr];
+ if (!atmel_default_console_device)
+ printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
void __init at91_add_device_serial(void)
{
int i;
}
}
#else
-void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
projects / linux-2.6-omap-h63xx.git / blobdiff