static struct resource nand_resources[] = {
{
.start = NAND_BASE,
- .end = NAND_BASE + SZ_8M - 1,
+ .end = NAND_BASE + SZ_256M - 1,
.flags = IORESOURCE_MEM,
}
};
else
cs_pin = spi_standard_cs[devices[i].chip_select];
- /* enable chip-select pin */
- at91_set_gpio_output(cs_pin, 1);
+ if (devices[i].chip_select == 0) /* for CS0 errata */
+ at91_set_A_periph(cs_pin, 0);
+ else
+ at91_set_gpio_output(cs_pin, 1);
+
/* pass chip-select pin to driver */
devices[i].controller_data = (void *) cs_pin;
#endif
+/* --------------------------------------------------------------------
+ * Timer/Counter blocks
+ * -------------------------------------------------------------------- */
+
+#ifdef CONFIG_ATMEL_TCLIB
+
+static struct resource tcb0_resources[] = {
+ [0] = {
+ .start = AT91RM9200_BASE_TCB0,
+ .end = AT91RM9200_BASE_TCB0 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91RM9200_ID_TC0,
+ .end = AT91RM9200_ID_TC0,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AT91RM9200_ID_TC1,
+ .end = AT91RM9200_ID_TC1,
+ .flags = IORESOURCE_IRQ,
+ },
+ [3] = {
+ .start = AT91RM9200_ID_TC2,
+ .end = AT91RM9200_ID_TC2,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91rm9200_tcb0_device = {
+ .name = "atmel_tcb",
+ .id = 0,
+ .resource = tcb0_resources,
+ .num_resources = ARRAY_SIZE(tcb0_resources),
+};
+
+static struct resource tcb1_resources[] = {
+ [0] = {
+ .start = AT91RM9200_BASE_TCB1,
+ .end = AT91RM9200_BASE_TCB1 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91RM9200_ID_TC3,
+ .end = AT91RM9200_ID_TC3,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = AT91RM9200_ID_TC4,
+ .end = AT91RM9200_ID_TC4,
+ .flags = IORESOURCE_IRQ,
+ },
+ [3] = {
+ .start = AT91RM9200_ID_TC5,
+ .end = AT91RM9200_ID_TC5,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91rm9200_tcb1_device = {
+ .name = "atmel_tcb",
+ .id = 1,
+ .resource = tcb1_resources,
+ .num_resources = ARRAY_SIZE(tcb1_resources),
+};
+
+static void __init at91_add_device_tc(void)
+{
+ /* this chip has a separate clock and irq for each TC channel */
+ at91_clock_associate("tc0_clk", &at91rm9200_tcb0_device.dev, "t0_clk");
+ at91_clock_associate("tc1_clk", &at91rm9200_tcb0_device.dev, "t1_clk");
+ at91_clock_associate("tc2_clk", &at91rm9200_tcb0_device.dev, "t2_clk");
+ platform_device_register(&at91rm9200_tcb0_device);
+
+ at91_clock_associate("tc3_clk", &at91rm9200_tcb1_device.dev, "t0_clk");
+ at91_clock_associate("tc4_clk", &at91rm9200_tcb1_device.dev, "t1_clk");
+ at91_clock_associate("tc5_clk", &at91rm9200_tcb1_device.dev, "t2_clk");
+ platform_device_register(&at91rm9200_tcb1_device);
+}
+#else
+static void __init at91_add_device_tc(void) { }
+#endif
+
+
/* --------------------------------------------------------------------
* RTC
* -------------------------------------------------------------------- */
/* --------------------------------------------------------------------
- * LEDs
+ * SSC -- Synchronous Serial Controller
* -------------------------------------------------------------------- */
-#if defined(CONFIG_LEDS)
-u8 at91_leds_cpu;
-u8 at91_leds_timer;
+#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
+static u64 ssc0_dmamask = DMA_BIT_MASK(32);
-void __init at91_init_leds(u8 cpu_led, u8 timer_led)
+static struct resource ssc0_resources[] = {
+ [0] = {
+ .start = AT91RM9200_BASE_SSC0,
+ .end = AT91RM9200_BASE_SSC0 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91RM9200_ID_SSC0,
+ .end = AT91RM9200_ID_SSC0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91rm9200_ssc0_device = {
+ .name = "ssc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ssc0_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc0_resources,
+ .num_resources = ARRAY_SIZE(ssc0_resources),
+};
+
+static inline void configure_ssc0_pins(unsigned pins)
{
- /* Enable GPIO to access the LEDs */
- at91_set_gpio_output(cpu_led, 1);
- at91_set_gpio_output(timer_led, 1);
+ if (pins & ATMEL_SSC_TF)
+ at91_set_A_periph(AT91_PIN_PB0, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_A_periph(AT91_PIN_PB1, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_A_periph(AT91_PIN_PB2, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_A_periph(AT91_PIN_PB3, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_A_periph(AT91_PIN_PB4, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_A_periph(AT91_PIN_PB5, 1);
+}
+
+static u64 ssc1_dmamask = DMA_BIT_MASK(32);
- at91_leds_cpu = cpu_led;
- at91_leds_timer = timer_led;
+static struct resource ssc1_resources[] = {
+ [0] = {
+ .start = AT91RM9200_BASE_SSC1,
+ .end = AT91RM9200_BASE_SSC1 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91RM9200_ID_SSC1,
+ .end = AT91RM9200_ID_SSC1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91rm9200_ssc1_device = {
+ .name = "ssc",
+ .id = 1,
+ .dev = {
+ .dma_mask = &ssc1_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc1_resources,
+ .num_resources = ARRAY_SIZE(ssc1_resources),
+};
+
+static inline void configure_ssc1_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_A_periph(AT91_PIN_PB6, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_A_periph(AT91_PIN_PB7, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_A_periph(AT91_PIN_PB8, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_A_periph(AT91_PIN_PB9, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_A_periph(AT91_PIN_PB10, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_A_periph(AT91_PIN_PB11, 1);
+}
+
+static u64 ssc2_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ssc2_resources[] = {
+ [0] = {
+ .start = AT91RM9200_BASE_SSC2,
+ .end = AT91RM9200_BASE_SSC2 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91RM9200_ID_SSC2,
+ .end = AT91RM9200_ID_SSC2,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91rm9200_ssc2_device = {
+ .name = "ssc",
+ .id = 2,
+ .dev = {
+ .dma_mask = &ssc2_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .resource = ssc2_resources,
+ .num_resources = ARRAY_SIZE(ssc2_resources),
+};
+
+static inline void configure_ssc2_pins(unsigned pins)
+{
+ if (pins & ATMEL_SSC_TF)
+ at91_set_A_periph(AT91_PIN_PB12, 1);
+ if (pins & ATMEL_SSC_TK)
+ at91_set_A_periph(AT91_PIN_PB13, 1);
+ if (pins & ATMEL_SSC_TD)
+ at91_set_A_periph(AT91_PIN_PB14, 1);
+ if (pins & ATMEL_SSC_RD)
+ at91_set_A_periph(AT91_PIN_PB15, 1);
+ if (pins & ATMEL_SSC_RK)
+ at91_set_A_periph(AT91_PIN_PB16, 1);
+ if (pins & ATMEL_SSC_RF)
+ at91_set_A_periph(AT91_PIN_PB17, 1);
}
+
+/*
+ * SSC controllers are accessed through library code, instead of any
+ * kind of all-singing/all-dancing driver. For example one could be
+ * used by a particular I2S audio codec's driver, while another one
+ * on the same system might be used by a custom data capture driver.
+ */
+void __init at91_add_device_ssc(unsigned id, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ /*
+ * NOTE: caller is responsible for passing information matching
+ * "pins" to whatever will be using each particular controller.
+ */
+ switch (id) {
+ case AT91RM9200_ID_SSC0:
+ pdev = &at91rm9200_ssc0_device;
+ configure_ssc0_pins(pins);
+ at91_clock_associate("ssc0_clk", &pdev->dev, "ssc");
+ break;
+ case AT91RM9200_ID_SSC1:
+ pdev = &at91rm9200_ssc1_device;
+ configure_ssc1_pins(pins);
+ at91_clock_associate("ssc1_clk", &pdev->dev, "ssc");
+ break;
+ case AT91RM9200_ID_SSC2:
+ pdev = &at91rm9200_ssc2_device;
+ configure_ssc2_pins(pins);
+ at91_clock_associate("ssc2_clk", &pdev->dev, "ssc");
+ break;
+ default:
+ return;
+ }
+
+ platform_device_register(pdev);
+}
+
#else
-void __init at91_init_leds(u8 cpu_led, u8 timer_led) {}
+void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
#endif
.num_resources = ARRAY_SIZE(uart0_resources),
};
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA17, 1); /* TXD0 */
at91_set_A_periph(AT91_PIN_PA18, 0); /* RXD0 */
- at91_set_A_periph(AT91_PIN_PA20, 0); /* CTS0 */
- /*
- * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21.
- * We need to drive the pin manually. Default is off (RTS is active low).
- */
- at91_set_gpio_output(AT91_PIN_PA21, 1);
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PA20, 0); /* CTS0 */
+
+ if (pins & ATMEL_UART_RTS) {
+ /*
+ * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21.
+ * We need to drive the pin manually. Default is off (RTS is active low).
+ */
+ at91_set_gpio_output(AT91_PIN_PA21, 1);
+ }
}
static struct resource uart1_resources[] = {
.num_resources = ARRAY_SIZE(uart1_resources),
};
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
{
- at91_set_A_periph(AT91_PIN_PB18, 0); /* RI1 */
- at91_set_A_periph(AT91_PIN_PB19, 0); /* DTR1 */
at91_set_A_periph(AT91_PIN_PB20, 1); /* TXD1 */
at91_set_A_periph(AT91_PIN_PB21, 0); /* RXD1 */
- at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD1 */
- at91_set_A_periph(AT91_PIN_PB24, 0); /* CTS1 */
- at91_set_A_periph(AT91_PIN_PB25, 0); /* DSR1 */
- at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS1 */
+
+ if (pins & ATMEL_UART_RI)
+ at91_set_A_periph(AT91_PIN_PB18, 0); /* RI1 */
+ if (pins & ATMEL_UART_DTR)
+ at91_set_A_periph(AT91_PIN_PB19, 0); /* DTR1 */
+ if (pins & ATMEL_UART_DCD)
+ at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD1 */
+ if (pins & ATMEL_UART_CTS)
+ at91_set_A_periph(AT91_PIN_PB24, 0); /* CTS1 */
+ if (pins & ATMEL_UART_DSR)
+ at91_set_A_periph(AT91_PIN_PB25, 0); /* DSR1 */
+ if (pins & ATMEL_UART_RTS)
+ at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS1 */
}
static struct resource uart2_resources[] = {
.num_resources = ARRAY_SIZE(uart2_resources),
};
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA22, 0); /* RXD2 */
at91_set_A_periph(AT91_PIN_PA23, 1); /* TXD2 */
+
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PA30, 0); /* CTS2 */
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PA31, 0); /* RTS2 */
}
static struct resource uart3_resources[] = {
.num_resources = ARRAY_SIZE(uart3_resources),
};
-static inline void configure_usart3_pins(void)
+static inline void configure_usart3_pins(unsigned pins)
{
at91_set_B_periph(AT91_PIN_PA5, 1); /* TXD3 */
at91_set_B_periph(AT91_PIN_PA6, 0); /* RXD3 */
+
+ if (pins & ATMEL_UART_CTS)
+ at91_set_B_periph(AT91_PIN_PB1, 0); /* CTS3 */
+ if (pins & ATMEL_UART_RTS)
+ at91_set_B_periph(AT91_PIN_PB0, 0); /* RTS3 */
}
static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
struct platform_device *atmel_default_console_device; /* the serial console device */
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
{
int i;
for (i = 0; i < config->nr_tty; i++) {
switch (config->tty_map[i]) {
case 0:
- configure_usart0_pins();
+ configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_uarts[i] = &at91rm9200_uart0_device;
at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart");
break;
case 1:
- configure_usart1_pins();
+ configure_usart1_pins(ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DSR | ATMEL_UART_DTR | ATMEL_UART_DCD | ATMEL_UART_RI);
at91_uarts[i] = &at91rm9200_uart1_device;
at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart");
break;
case 2:
- configure_usart2_pins();
+ configure_usart2_pins(0);
at91_uarts[i] = &at91rm9200_uart2_device;
at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart");
break;
case 3:
- configure_usart3_pins();
+ configure_usart3_pins(0);
at91_uarts[i] = &at91rm9200_uart3_device;
at91_clock_associate("usart3_clk", &at91rm9200_uart3_device.dev, "usart");
break;
printk(KERN_INFO "AT91: No default serial console defined.\n");
}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+ struct platform_device *pdev;
+
+ switch (id) {
+ case 0: /* DBGU */
+ pdev = &at91rm9200_dbgu_device;
+ configure_dbgu_pins();
+ at91_clock_associate("mck", &pdev->dev, "usart");
+ break;
+ case AT91RM9200_ID_US0:
+ pdev = &at91rm9200_uart0_device;
+ configure_usart0_pins(pins);
+ at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+ break;
+ case AT91RM9200_ID_US1:
+ pdev = &at91rm9200_uart1_device;
+ configure_usart1_pins(pins);
+ at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+ break;
+ case AT91RM9200_ID_US2:
+ pdev = &at91rm9200_uart2_device;
+ configure_usart2_pins(pins);
+ at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+ break;
+ case AT91RM9200_ID_US3:
+ pdev = &at91rm9200_uart3_device;
+ configure_usart3_pins(pins);
+ at91_clock_associate("usart3_clk", &pdev->dev, "usart");
+ break;
+ default:
+ return;
+ }
+ pdev->id = portnr; /* update to mapped ID */
+
+ if (portnr < ATMEL_MAX_UART)
+ at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+ if (portnr < ATMEL_MAX_UART)
+ atmel_default_console_device = at91_uarts[portnr];
+ if (!atmel_default_console_device)
+ printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
void __init at91_add_device_serial(void)
{
int i;
}
}
#else
-void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
{
at91_add_device_rtc();
at91_add_device_watchdog();
+ at91_add_device_tc();
return 0;
}