config ARCH_AT91SAM9RL
bool "AT91SAM9RL"
+config ARCH_AT91CAP9
+ bool "AT91CAP9"
+
config ARCH_AT91X40
bool "AT91x40"
Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit
<http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3933>
+config MACH_CAM60
+ bool "KwikByte KB9260 (CAM60) board"
+ depends on ARCH_AT91SAM9260
+ help
+ Select this if you are using KwikByte's KB9260 (CAM60) board based on the Atmel AT91SAM9260.
+ <http://www.kwikbyte.com/KB9260.html>
+
endif
# ----------------------------------------------------------
# ----------------------------------------------------------
+if ARCH_AT91CAP9
+
+comment "AT91CAP9 Board Type"
+
+config MACH_AT91CAP9ADK
+ bool "Atmel AT91CAP9A-DK Evaluation Kit"
+ depends on ARCH_AT91CAP9
+ help
+ Select this if you are using Atmel's AT91CAP9A-DK Evaluation Kit.
+ <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4138>
+
+endif
+
+# ----------------------------------------------------------
+
if ARCH_AT91X40
comment "AT91X40 Board Type"
config MTD_AT91_DATAFLASH_CARD
bool "Enable DataFlash Card support"
- depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK)
+ depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK)
help
Enable support for the DataFlash card.
config MTD_NAND_AT91_BUSWIDTH_16
bool "Enable 16-bit data bus interface to NAND flash"
- depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK)
+ depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK)
help
On AT91SAM926x boards both types of NAND flash can be present
(8 and 16 bit data bus width).
Select this if you need to program one or more of the PCK0..PCK3
programmable clock outputs.
+config AT91_TIMER_HZ
+ int "Kernel HZ (jiffies per second)"
+ range 32 1024
+ depends on ARCH_AT91
+ default "128" if ARCH_AT91RM9200
+ default "100"
+ help
+ On AT91rm9200 chips where you're using a system clock derived
+ from the 32768 Hz hardware clock, this tick rate should divide
+ it exactly: use a power-of-two value, such as 128 or 256, to
+ reduce timing errors caused by rounding.
+
+ On AT91sam926x chips, or otherwise when using a higher precision
+ system clock (of at least several MHz), rounding is less of a
+ problem so it can be safer to use a decimal values like 100.
+
+choice
+ prompt "Select a UART for early kernel messages"
+
+config AT91_EARLY_DBGU
+ bool "DBGU"
+
+config AT91_EARLY_USART0
+ bool "USART0"
+
+config AT91_EARLY_USART1
+ bool "USART1"
+
+config AT91_EARLY_USART2
+ bool "USART2"
+ depends on ! ARCH_AT91X40
+
+config AT91_EARLY_USART3
+ bool "USART3"
+ depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260)
+
+config AT91_EARLY_USART4
+ bool "USART4"
+ depends on ARCH_AT91SAM9260
+
+config AT91_EARLY_USART5
+ bool "USART5"
+ depends on ARCH_AT91SAM9260
+
+endchoice
+
endmenu
endif