config ARM
bool
default y
+ select HAVE_IDE
select RTC_LIB
select SYS_SUPPORTS_APM_EMULATION
select HAVE_OPROFILE
select TIMER_ACORN
select ISA
select NO_IOPORT
- select HAVE_IDE
help
Support for the Cirrus Logic PS7500FE system-on-a-chip.
bool "Co-EBSA285"
select FOOTBRIDGE
select FOOTBRIDGE_ADDIN
- select HAVE_IDE
help
Support for Intel's EBSA285 companion chip.
select ARM_AMBA
select ARM_VIC
select GENERIC_GPIO
+ select HAVE_GPIO_LIB
help
This enables support for the Cirrus EP93xx series of CPUs.
config ARCH_FOOTBRIDGE
bool "FootBridge"
select FOOTBRIDGE
- select HAVE_IDE
help
Support for systems based on the DC21285 companion chip
("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
depends on MMU
select PLAT_IOP
select PCI
- select HAVE_IDE
help
Support for Intel's 80219 and IOP32X (XScale) family of
processors.
depends on MMU
select PLAT_IOP
select PCI
- select HAVE_IDE
help
Support for Intel's IOP33X (XScale) family of processors.
config ARCH_IXP23XX
bool "IXP23XX-based"
depends on MMU
- select HAVE_IDE
select PCI
help
Support for Intel's IXP23xx (XScale) family of processors.
select GENERIC_GPIO
select GENERIC_TIME
select GENERIC_CLOCKEVENTS
- select HAVE_IDE
help
Support for Intel's IXP4XX (XScale) family of processors.
config ARCH_L7200
bool "LinkUp-L7200"
select FIQ
- select HAVE_IDE
help
Say Y here if you intend to run this kernel on a LinkUp Systems
L7200 Software Development Board which uses an ARM720T processor.
help
Support for Freescale MXC/iMX-based family of processors
-config ARCH_ORION
+config ARCH_ORION5X
bool "Marvell Orion"
depends on MMU
select PCI
select GENERIC_GPIO
select GENERIC_TIME
select GENERIC_CLOCKEVENTS
+ select PLAT_ORION
help
- Support for Marvell Orion System on Chip family.
+ Support for the following Marvell Orion 5x series SoCs:
+ Orion-1 (5181), Orion-NAS (5182), Orion-2 (5281.)
config ARCH_PNX4008
bool "Philips Nexperia PNX4008 Mobile"
depends on MMU
select ARCH_MTD_XIP
select GENERIC_GPIO
- select HAVE_IDE
select HAVE_GPIO_LIB
select GENERIC_TIME
select GENERIC_CLOCKEVENTS
select ARCH_MAY_HAVE_PC_FDC
select ISA_DMA_API
select NO_IOPORT
- select HAVE_IDE
help
On the Acorn Risc-PC, Linux can support the internal IDE disk and
CD-ROM interface, serial and parallel port, and the floppy drive.
bool "SA1100-based"
select ISA
select ARCH_DISCONTIGMEM_ENABLE
+ select ARCH_SPARSEMEM_ENABLE
+ select ARCH_SELECT_MEMORY_MODEL
select ARCH_MTD_XIP
select GENERIC_GPIO
select GENERIC_TIME
- select HAVE_IDE
+ select GENERIC_CLOCKEVENTS
+ select TICK_ONESHOT
+ select HAVE_GPIO_LIB
help
Support for StrongARM 11x0 based boards.
config ARCH_S3C2410
bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442, S3C2443"
select GENERIC_GPIO
- select HAVE_IDE
help
Samsung S3C2410X CPU based systems, such as the Simtec Electronics
BAST (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or
config ARCH_SHARK
bool "Shark"
- select HAVE_IDE
select ISA
select ISA_DMA
select PCI
config ARCH_LH7A40X
bool "Sharp LH7A40X"
- select HAVE_IDE
help
Say Y here for systems based on one of the Sharp LH7A40X
System on a Chip processors. These CPUs include an ARM922T
config ARCH_OMAP
bool "TI OMAP"
select GENERIC_GPIO
+ select HAVE_GPIO_LIB
select GENERIC_TIME
select GENERIC_CLOCKEVENTS
help
source "arch/arm/mach-omap2/Kconfig"
-source "arch/arm/mach-orion/Kconfig"
+source "arch/arm/mach-orion5x/Kconfig"
source "arch/arm/plat-s3c24xx/Kconfig"
source "arch/arm/plat-s3c/Kconfig"
config PLAT_IOP
bool
+config PLAT_ORION
+ bool
+
source arch/arm/mm/Kconfig
config IWMMXT
config SMP
bool "Symmetric Multi-Processing (EXPERIMENTAL)"
- depends on EXPERIMENTAL && REALVIEW_EB_ARM11MP
+ depends on EXPERIMENTAL && (REALVIEW_EB_ARM11MP || MACH_REALVIEW_PB11MP)
+ select USE_GENERIC_SMP_HELPERS
help
This enables support for systems with more than one CPU. If you have
a system with only one CPU, like most personal computers, say N. If
config LOCAL_TIMERS
bool "Use local timer interrupts"
- depends on SMP && REALVIEW_EB_ARM11MP
+ depends on SMP && (REALVIEW_EB_ARM11MP || MACH_REALVIEW_PB11MP)
default y
help
Enable support for local timers on SMP platforms, rather then the
or have huge holes in the physical address space for other reasons.
See <file:Documentation/vm/numa> for more.
+config ARCH_SPARSEMEM_ENABLE
+ bool
+
+config ARCH_SELECT_MEMORY_MODEL
+ bool
+
config NODES_SHIFT
int
default "4" if ARCH_LH7A40X
source "drivers/dca/Kconfig"
+source "drivers/uio/Kconfig"
+
endmenu
source "fs/Kconfig"